steering GMC C-SERIES 1999 Owner's Manual

yellowblue
5-2
Hazard Warning Flashers
Your hazard warning flashers let you warn others. They
also let police know you have a problem. Your front and
rear turn signal lamps will flash on and off.
The hazard flasher switch is located on the
steering column.
Press the button in to make your front and rear turn
signal lamps flash on and off.
Your hazard warning flashers work no matter what
position your key is in, and even if the key isn't in.
To turn off the flashers, pull out on the collar. When
the hazard warning flashers are on, your turn signals
won't work.
ProCarManuals.com

yellowblue
5-3 Hazard Warning Flasher Switch
(If Equipped)
With some options, such as U86-trailer wiring or
RQ3
-tractor application, you will have this switch.
This switch replaces the hazard switch mounted on the
steering column. It is mounted in the instrument panel,
usually to the left of and below the steering column.
Pull the switch out to make your front and rear turn
signal lamps flash on and off. A light next to the switch
will also flash. Push it back in to turn off the flashers.
The turn signal lamps won't flash if you're braking.
This switch works no matter what position the key is in,
and even if the key isn't in the ignition.
When the hazard warning flashers are on, your turn
signals won't work.
ProCarManuals.com

yellowblue
5-14
After Towing
Block the rear wheels and install axle and propeller
shafts. Check for proper phasing of universal joints.
Apply the emergency brake system before disconnecting
from the towing vehicle. Check and fill the rear axle
with oil as required.
Towing Your Vehicle From the Front
(All Wheels On the Ground)
Your vehicle may be towed on all wheels provided the
steering is working. Remember that the power brakes
and power steering will not have power assist. Vehicles
with air brakes will not have brakes. There must be a
tow bar installed between the towing vehicle and the
disabled vehicle.
Before Towing
Block the wheels of the disabled vehicle. On vehicles
with air brakes, release the emergency brake system by
compressing the brake chamber springs as outlined in
this section. (Note: This is to prevent the possibility of
the emergency brake being applied during towing.)On vehicles with hydraulic brakes, release the
parking brake fully by moving the lever to the
fully
-released position.
On vehicles equipped with an electric/hydraulic parking
brake, remove the propshaft.
Disconnect the propshaft at the rear axle (forward axle
on tandem axle models). Secure the propshaft to the
frame or crossmember.
If there is damage or suspected damage to the axle(s),
remove the axle shafts. Cover the hub openings to
prevent the loss of lubricant or entry of dirt or
foreign objects.
After Towing
Block the rear wheels and install axle and propshafts.
Check for proper phasing of universal joints. Apply
the parking brake system before disconnecting from
the towing vehicle. Check and fill rear axle with oil
as required.
ProCarManuals.com

yellowblue
5-15 Towing Your Vehicle From the Rear
(Rear Wheels Off the Ground)
Before Towing
Secure the steering wheel to maintain a straight
-ahead
position. Make certain that the front axle is not loaded
above the front axle Gross Axle Weight Rating (GAWR)
as indicated on the vehicle's Certification/Tire label.
After Towing
Block the rear wheels and release the steering. Apply the
parking brake system before disconnecting from the
towing vehicle.
Refer to the transmission shift label for
additional information.
Releasing Air-Operated Parking Brakes
If your vehicle has air brakes, you could have a special
towing problem. If your vehicle has to be towed because
you had a complete loss of air pressure from both
systems, the parking brakes may have applied. The tow
operator can release the brakes manually by using the
following steps. Then your vehicle can be towed with all
wheels or just the rear wheels on the ground.
ProCarManuals.com

yellowblue
5-34
If a Tire Goes Flat
It's unusual for a tire to ªblow outº while you're driving,
especially if you maintain your tires properly. If air goes
out of a tire, it's much more likely to leak out slowly.
But if you should ever have a ªblowout,º here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you'd use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.
If a tire goes flat, the next part tells you what to do.
Changing a Flat Tire
A flat or damaged tire can be a major roadside problem.
You're very likely to have to go for help. Few drivers of
these vehicles have the necessary equipment aboard to
be able to change a flat tire safely. For example, youhave to have a truck jack that can lift several thousand
pounds and a torque wrench that can generate several
hundred foot
-pounds (newton-meters) of twisting force.
So if you're stopped somewhere by a flat or damaged
tire or wheel, you should get expert help right then.
If the correct equipment is available, though, here is the
procedure to follow.

Does the tire still seem to have air under pressure in
it? If so, stand to the side and look at the wheel. See
if it looks like another wheel on the vehicle. If so, go
on to the next step. If it doesn't, or even if you can't
be sure, stop and get expert help.
CAUTION:
Tire-rim assemblies can explode. If you work on
a pressurized tire mounted on a damaged wheel,
the assembly can expand with explosive force
without warning. You and others nearby can be
badly injured. Don't work around a tire that has
air under pressure in it when its wheel is or might
be damaged.
ProCarManuals.com

yellowblue
5-38
NOTICE:
Spinning your wheels can destroy parts of your
vehicle as well as the tires. If you spin the wheels
too fast while shifting your transmission back
and forth, you can destroy your transmission.
Rocking Your Vehicle To Get It Out
First, turn your steering wheel left and right. That will
clear the area around your front wheels. Then shift back
and forth between REVERSE (R) and a forward gear
(or with a manual transmission, between FIRST (1) or
SECOND (2) and REVERSE (R)), spinning the wheels
as little as possible. Release the accelerator pedal while
you shift, and press lightly on the accelerator pedal
when the transmission is in gear. By slowly spinning
your wheels in the forward and reverse directions, you
will cause a rocking motion that may free your vehicle.
If that doesn't get you out after a few tries, you may
need to be towed out. If you do need to be towed out,
see ªTowing Your Vehicleº in the Index.
ProCarManuals.com

6-
yellowblue
6-1
Section 6 Service and Appearance Care
Here you will find information about the care of your vehicle. This section begins with service and fuel information,
and then it shows how to check important fluid and lubricant levels. There is also technical information about your
vehicle, and a part devoted to its appearance care.
6
-2 Service
6
-4 Fuel (Gasoline Engine)
6
-5 Diesel Fuel Requirements and Fuel System
6
-6 Fuels in Foreign Countries (Gasoline Engines)
6
-7 Filling Your Tank
6
-8 Filling a Portable Fuel Container
6
-9 Checking Things Under the Hood
6
-11 Noise Control System
6
-13 Engine Oil (Gasoline Engine)
6
-17 Engine Oil (Caterpillar
Diesel Engine)
6
-17 Engine Air Cleaner/Filter
6
-18 Automatic Transmission Fluid
6
-19 Manual Transmission Fluid
6
-20 Rear Axle
6
-20 Rear Axle Shift Motor (Option)
6
-21 Radiator Pressure Cap (Gasoline Engines)
6
-22 Surge Tank Pressure Cap (Diesel Engines)
6
-22 Thermostat6
-23 Engine Coolant (Gasoline Engine)
6
-27 Engine Coolant (Caterpillar
Diesel Engine)
6
-28 Power Steering Fluid
6
-29 Windshield Washer Fluid
6
-30 Brakes
6
-36 Electric/Hydraulic Parking Brake Fluid
6
-42 Battery
6
-44 Other Service Items
6
-48 Tires
6
-59 Appearance Care
6
-59 Cleaning the Inside of Your Vehicle
6
-63 Cleaning the Outside Your Vehicle
6
-66 GM Vehicle Care/Appearance Materials
6
-67 Vehicle Identification Number (VIN)
6
-67 Service Parts Identification Label
6
-68 Electrical System
6
-74 Capacities and Specifications
6
-77 Air Conditioning Refrigerants
ProCarManuals.com

yellowblue
6-28
Power Steering Fluid
See your Maintenance Schedule for when to check your
power steering fluid.
How To Check Power Steering Fluid
Check your power steering fluid only when the engine is
warm. If the engine isn't warm, you probably won't get
an accurate reading.
Vehicles with diesel engines
have a sight glass. If you
can see fluid in the glass,
you have enough.Other models have a cap with a dipstick. If you have
one, unscrew the cap and check the dipstick. It should be
between ADD and FULL (if the engine is warm).
If you need to add some, put in only enough of the
correct fluid to bring the level up to the FULL mark (if
you have the dipstick) or so you can see fluid in the
glass, if you have a sight glass.
ProCarManuals.com

yellowblue
6-29 What to Use
To determine what kind of fluid to use, see
ªRecommended Fluids and Lubricantsº in the Index.
NOTICE:
When adding power steering fluid or making a
complete fluid change, always use the proper
fluid. Failure to use the proper fluid can cause
leaks and damage hoses and seals.
If your power steering fluid level is low, this can
cause the PRIMARY BRAKE or AUX BRAKE
warning lights to come on. If either light remains
on after you have added power steering fluid to
the proper level, then shut off the engine for
10 seconds. This should reset the brake warning
lights. If one or both lights stay on, though,
then see ªHydraulic Brake Warning Lightsº in
the Index.
Windshield Washer Fluid
What to Use
When you need windshield washer fluid, be sure to read
the manufacturer's instructions before use. If you will be
operating your vehicle in an area where the temperature
may fall below freezing, use a fluid that has sufficient
protection against freezing.
Adding Washer Fluid
Open the cap labeled WASHER FLUID ONLY.
Add washer fluid until the tank is full.
ProCarManuals.com

yellowblue
6-39
ITEM NO. ITEM REMARKS
1 Brake Camshaft
, Brake Caliper
Rails (If Equipped)$One fitting each (apply sparingly). For caliper rails,
apply Aero Shell #5 Lubricant.
2 Steering Column Slip Joint* One fitting.
3 Steering Drag Link Ends One fitting at each end.
4 Steering Column U
-Joints One fitting each joint.
5 Pivot Points and Hinges Apply chassis lubricant.
6 Slack Adjuster
One fitting.
7 Brake Cam Roller Pins at interface
of pin and shoe
Apply engine oil.
8 Front Steering Knuckles One fitting each side, lower bushing (hand
-operated
grease gun only). Hand
-pack upper bearing.
9 Front Wheel Bearings Hand
-pack or lubricate.
10 Steering Tie Rod Ends One fitting each end.
11 Spring Slip Pads*
(Multi
-Leaf Only)Apply chassis lubricant.
12 Clutch Release Bearing* Cup or fitting.
13 Battery Terminal
(except ªSTº type)Keep coated with petroleum jelly.
14 Parking Brake Bell Crank*$ One fitting.
ProCarManuals.com