automatic transmission GMC C-SERIES 1999 Owners Manual

2-
yellowblue
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Keys
2
-4 Door Locks
2
-5 Theft
2
-5 New Vehicle ªBreak-Inº
2
-6 Ignition Positions
2
-7 Starting Your Gasoline Engine
2
-10 Starting Your Diesel Engine
2
-13 Engine Checks Before Operating
2
-15 Engine Coolant Heater (If Equipped)
2
-16 Diesel Engine Exhaust Brake
2
-17 Two-Speed Rear Axle Electric Shift Control
(If Equipped)
2
-20 Automatic Transmission Operation
2
-22 Manual Transmission Operation
2
-23 Parking
2
-29 Parking Over Things That Burn
2
-29 Engine Exhaust2
-30 Running Your Engine While You're Parked
(Automatic Transmission)
2
-30 Windows
2
-31 Tilt Wheel (If Equipped)
2
-32 Turn Signal/Multifunction Lever
2
-39 Trailer Brake Hand Control Valve (Option)
2
-40 Inter-Axle Differential Lock Control
(If Equipped)
2
-41 Rear Axle Differential Lock Control
(If Equipped)
2
-42 Engine Air Control (If Equipped)
2
-43 Exterior Lamps
2
-46 Interior Lamps
2
-46 Mirrors
2
-50 Instrument Panel
2
-52 Instrument Panel Cluster
2
-55 Warning Lights, Gages and Indicators
ProCarManuals.com

yellowblue
2-7
ACCESSORY (A): This position lets you use
accessories when the engine is off. To use
ACCESSORY, push in the key and turn it toward you.
LOCK (B): This position locks your ignition. You will
be able to remove your key only when the switch is in
this position.
OFF (C): This position lets you turn off the engine, but
the key can't be removed.
RUN (D): This is the position for driving and activating
the CAT diesel air inlet heater (if equipped).
START (E): This position starts your engine.
Engine Starter Over-Crank Protection
(If Equipped)
Some vehicles have an engine starter over-crank
protection system. This system includes a built
-in
temperature limiting switch to prevent internal damage
to the starter. If the starter motor overheats and shuts
off due to over
-cranking, the motor must cool down
before the switch will reset and allow you to operate the
starter. It can take up to six minutes before the starter
will work again.
Starting Your Gasoline Engine
Engines start differently. The 8th digit of your Vehicle
Identification Number (VIN) shows the code letter for
your engine. (See ªVehicle Identification Numberº in
the Index.) Follow the proper steps to start the engine.
To start a diesel engine, see ªStarting Your Diesel
Engineº in the Index.
Automatic Transmission
Set the parking brake and move your shift lever to
NEUTRAL (N) or PARK (P) if so equipped. Your
engine won't start in any other position
-- that's a
safety feature.
ProCarManuals.com

yellowblue
2-9
NOTICE:
Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don't,
your engine might not perform properly.
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Gasoline Engine Warm-Up
When you've started your engine, let it run for 20 or
30 seconds to warm up before you put a load on
the engine.
Drive at moderate speeds for the first few miles,
especially in cold weather. Running a cold engine at
high speed can damage it.
Restarting the Gasoline Engine While
Moving (Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic
transmission to NEUTRAL (N). This safety feature
prevents starting the engine when the transmission is in
a drive gear.
Stopping the Gasoline Engine
Let your engine idle for a few seconds before turning it
off after you have finished driving your vehicle.
If you shift to NEUTRAL (N), set the parking brake.
If you shift to PARK (P), the auto
-apply feature will set
the parking brake.
If your vehicle has a two
-speed axle, put the range
selector in LOW. To be sure the axle has shifted into
LOW, engage the clutch and transmission the vehicle
may move slightly when you do this.
While your engine is idling before you turn it off, you
can make a list of any operational or handling concerns
to give to responsible maintenance personnel so they can
handle them right away.
Moisture will condense in a fuel tank that is almost
empty if the vehicle is not run for a while, even just
overnight under some conditions. So, it's always best to
refuel your vehicle at the end of each run.
ProCarManuals.com

yellowblue
2-10
Starting Your Diesel Engine
If you have a Caterpillar diesel engine, also refer to
your Caterpillar
Operation & Maintenance Manual for
starting procedure.
To make starting easier in cold weather (below 32F or
0C), the proper viscosity engine oil should be used. It's
also best to heat the engine oil first. You can do this by
using an engine coolant heater. A GM Automatic Ether
Injection System aids cold weather starting.
NOTICE:
Your diesel engine has an electric air intake
heater system which reduces white smoke and
helps start the engine in cold weather. Do not
spray starting fluid into the air intake where it
can contact the heater elements.
If you don't have the GM Automatic Ether
Injection System, don't use starting fluid or
you could damage your engine. If you have the
GM system, use only GM approved starting fluid
that has been tested to establish compatibility
with the air inlet heater system.
NOTICE:
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Restarting the Diesel Engine While Moving
(Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic transmission
to NEUTRAL (N). This safety feature prevents starting
the engine when the transmission is in a drive gear.
Stopping the Diesel Engine
If you have a Caterpillar diesel engine, see your
Caterpillar
Operation & Maintenance Manual.
1. Set the parking brake and shift to NEUTRAL (N) or
PARK (P).
2. Turn the ignition switch key to OFF.
If your vehicle has a two
-speed axle, see ªRear Axle,
Tw o
-Speed Electric Shift Controlº or ªRear Axle,
Tw o
-Speed Airshift Controlº in the Index.
ProCarManuals.com

yellowblue
2-11 Cold Weather Starting (Caterpillar

Diesel)
Because the diesel engine uses compression ignition, it
is harder to start in cold weather than a gasoline engine.
The air intake heater and use of the proper engine oil,
optional engine coolant heaters and optional ether
injection systems help cold weather starting. See the
Caterpillar

Operation & Maintenance Manual for
more information.
Diesel Engine Warm-Up
Several factors affect how quickly your diesel engine
warms up. These can include outside temperature,
engine load, idle time and your vehicle's option content.
Your vehicle may be equipped with some features that
can help the engine reach operating temperature sooner.
Some of these features are discussed below.
Also, remember that an automatic transmission adds
heat to the cooling system through the heat exchanger in
the radiator. Because of this, vehicles equipped with
automatic transmissions are often able to retain engine
coolant heat better than manual transmission vehicles.
See your Caterpillar

Operation & Maintenance manual
for additional diesel engine warm
-up information.
Engine Automatic Shutdown (If Equipped)
Your CHECK GAGES light will come on if the system
senses high engine temperature or low engine oil
pressure. If high engine temperature is detected, you
will also hear a tone alarm at two beats per second. The
alarm and the light will remain on until the condition is
fixed. If the engine temperature condition worsens, the
tone alarm will go to five beats per second. When a low
oil pressure condition is detected, the five beat per
second alarm will come on immediately.
If the system senses low engine coolant, the five beat
per second alarm and the LOW COOLANT warning
light will come on.
The five beats per second tone alarm means that your
engine will shut down in 25 seconds. Pull off the road
and shut off the engine. Don't start it until the reason for
the problem is known, and the problem is fixed. If the
engine shuts down when you are still in traffic, you can
restart the engine and get another 25 seconds of
operation. Do this only if you have to, since there is a
problem that can harm the engine if it isn't fixed.
ProCarManuals.com

yellowblue
2-12 Fast Idle System (Electronically Controlled
Caterpillar

Diesel and Gasoline Engines)
If your vehicle is equipped with an electronically
controlled diesel engine, it has both automatic and
manual fast idle capabilities.
Automatic Fast Idle System
(Caterpillar

Diesel Engine Only)
The automatic fast idle feature will engage whenever
you start your vehicle and the engine is below the preset
operating temperature. This will help decrease engine
warm
-up time.
Idle speed will then return to normal under any of the
following conditions:

The engine reaches the preset operating temperature.

The brake pedal is pressed.

The trailer brake hand lever (if equipped) is applied.

The manual transmission clutch pedal is pressed or,
the automatic transmission (if equipped) is shifted
from NEUTRAL (N) or PARK (P).

The vehicle speed exceeds approximately
10 mph (16 km/h).

When the fast idle switch is pressed a second time.Manual Fast Idle System
(Caterpillar
 Diesel and Gasoline Engines)
The manual fast idle switch
is located on the lower
portion of the instrument
panel just to the left of the
steering wheel.
This system can be used to increase your engine idle
speed whenever the following conditions are met:

The brake pedal is not pressed.

The trailer brake hand lever (if equipped) is not applied.

The vehicle speed is below approximately
10 mph (16km/h).

The manual transmission (if equipped) clutch pedal
is not pressed or, the automatic transmission
(if equipped) is in NEUTRAL (N).
ProCarManuals.com

yellowblue
2-17
The accelerator and clutch pedals must be released in
order for the exhaust brake to engage. Whenever the
exhaust brake is active, the light in the switch will be on.
Do not use the exhaust brake when running the engine at
idle during warm
-up or other extended periods.
Prolonged use of the exhaust brake during idling will
cause the engine to overheat.
CAUTION:
Be careful when using the exhaust brake or you
could lock the wheels and lose control of the
vehicle. Operators not familiar with an exhaust
brake should not use this brake on slippery
surfaces before learning to use it on dry surfaces.
If the vehicle's wheels begin to lock when using
the exhaust brake on slippery surfaces, switch the
exhaust brake off immediately. The exhaust
brake will turn off if the anti
-lock brake system
is activated.
Tw o-Speed Rear Axle Electric Shift
Control (If Equipped)
If your vehicle has this feature, you'll find a label (or
labels) on the ceiling above the windshield or in another
place near the driver that show how to use it. Be sure
to follow the directions carefully. Use the following
directions based on the type of shift control you have.
Automatic Transmission
The switch for the rear axle
shift control is on the shift
tower to the right of the
shift lever.
When the switch is up, the rear axle is in the high range.
Push it down to get the low range.
ProCarManuals.com

yellowblue
2-20
Air Suspension Dump Control (If Equipped)
If your vehicle is equipped with the Hendrickson HAS
Series single
-axle air suspension, you may have this
control. The air suspension dump control allows the
operator to lower the deck height approximately
4.5 inches (11.5 cm) from the normal frame height.
The switch to deflate and
inflate the air suspension is
located on the upper left
side of the instrument panel
above the driver's side vent.
The light in the switch will be illuminated whenever the
switch is in the ªdumpedº position.
Automatic Transmission Operation
We build vehicles with four, five and six-speed
automatic transmissions. This part of the manual covers
the basics of these. With some of the transmissions, you
will find another manual in your vehicle that goes into
more detail. On the ceiling, in front of and above the
driver, or in some other place near the driver, you will
see a label that describes important operating facts about
the automatic transmission in your vehicle. Make sure
you follow the instructions on this label.
You may have a PARK (P) position for your shift lever.
This position locks your rear wheels. It is the best
position to use when you start your engine because your
vehicle can't move easily.
All vehicles equipped with automatic transmissions
can be started in PARK (P), if equipped, or in
NEUTRAL (N). When you shift out of NEUTRAL (N),
you may have to hold in a push button on the shift lever
or lift up on a release handle as you shift. See the
Allison Automatic Transmission Operator's Manual in
your vehicle for more information about this.
ProCarManuals.com

yellowblue
2-21
CAUTION:
It is dangerous to get out of your vehicle if the
shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don't leave your vehicle when the engine is
running unless you have to. If you have left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won't move, even when you're on fairly
level ground, always set your parking brake and
move the shift lever to PARK (P).
See ªShifting Into PARK (P)º in the Index.
CAUTION:
Shifting out of PARK (P) or NEUTRAL (N) while
your engine is ªracingº (running at high speed) is
dangerous. Unless your foot is firmly on the
brake pedal, your vehicle could move very
rapidly. You could lose control and hit people or
objects. Don't shift out of PARK (P) or
NEUTRAL (N) while your engine is racing.
Automatic Transmission Third Gear Hold
(If Equipped)
If you have this feature, your range selector has a
ª2
-3º position. You can't shift up to the next higher
gear when the transmission is in this position unless
your engine
-governed speed is exceeded, such as when
going downhill.
This feature is useful for certain load and traffic
conditions or when plowing snow. See the Allison
Automatic Transmission Operator's Manual in your
vehicle for further information.
ProCarManuals.com

yellowblue
2-22
Manual Transmission Operation
This part of the manual covers the basics of the manual
transmission. With some of the transmissions, you
will find another manual in your vehicle that goes into
more detail.
Using the Clutch
When you're starting to move the vehicle, it's important
to begin with the engine speed at idle. Then start to
engage the clutch and listen for an engine speed drop of
about 100 rpm. At this point, the clutch is engaging, so
you should increase the engine speed and fully engage
the clutch. It's important not to increase the engine
speed sooner or before the clutch begins its engagement.
If you do, you can cause damage to your vehicle.
Double-Clutching
You must use the ªdouble-clutchingº method when you
shift an unsynchronized gear set. Simply disengage the
clutch, shift to NEUTRAL (N) and engage the clutch.
When you're shifting down to a lower gear, accelerate
the engine speed while in NEUTRAL (N) to get ready
for the lower gear.
Eaton Fuller 5 and 6-Speed Transmissions
and Dana Spicer 7-Speed Transmissions
These transmissions have gears that automatically
synchronize when you shift up or down (except
FIRST (1) gear on the five
-speed transmission which is
unsynchronized). Choose the gear which will maintain
the road speed you want while keeping the engine above
two
-thirds of the governed speed. When the engine
speed drops below two
-thirds of the governed speed,
shift into the next lower gear before your engine begins
to lug. When you shift down, be sure to double
-clutch
if required.
Eaton Fuller 9 and 10-Speed
Manual Transmissions
If your vehicle has one of these unsynchronized
transmissions, it's naturally somewhat complicated.
The label above the windshield will tell you the
operating basics you need to know.
Before operating the vehicle with one of these
transmissions, be sure to read the Eaton Fuller
Transmission Driver Instructions Manual in your vehicle.
ProCarManuals.com