lock GMC ENVOY 2002 Service Manual

2-62
To slide the crossrails to where you want them, pull up
on the lever on each side of the crossrail. This will
release the crossrail and allow you to slide it. When the
crossrail is where you want it, push down on the lever
to lock it into place.
NOTICE:
Loading cargo that weighs more than 220 lbs.
(100 kg) on the luggage carrier may damage
your vehicle.
When you carry cargo on the luggage carrier of
a proper size and weight, put it on the slats, and
distribute the weight evenly. Then slide the
crossrail up against the rear of the load, to help
keep it from moving. You can then tie it down.
Cargo containers must be loaded on the
crossrails only.
Don't exceed the maximum vehicle capacity when loading
your vehicle. For more information on vehicle capacity
and loading, see ªLoading Your Vehicleº in the Index.To prevent damage or loss of cargo as you're driving,
check now and then to make sure the luggage carrier is
locked and cargo is still securely fastened.
When the luggage carrier is not in use, place the cross
rails at the following positions for wind noise reduction.
Place one cross rail at the rear most point of the vehicle
and the other above the opening of the rear door.
Ashtrays and Cigarette Lighter
The front ashtray is removable and fits into the
front cupholder.
NOTICE:
Don't put papers and other things that burn into
your ashtray. If you do, cigarettes or other smoking
materials could set them on fire, causing damage.
To remove the front ashtray, pull the covered bin out of
the cupholder.
To use the lighter, press it in all the way, and let go.
When it's ready, it will pop back out by itself.

2-63
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overload, damaging the
lighter and the heating element.
Sun Visors
To block out glare, you can pull the visor down. You can
also swing the visor from side
-to-side.
Illuminated Visor Vanity Mirror
Pull the sun visor down and lift the mirror cover to turn
on the lamps.
Accessory Inflator (If Equipped)
Your vehicle may be equipped with an air inflator
system. You can inflate things like basketballs and
bicycle tires. Also, you can use it to bring your tire
pressure up to the proper pressure. It is not designed to
inflate large objects which will require more than five
minutes to inflate, such as an air mattress.
The air inflator is located
in the rear compartment
on the passenger's side
of the vehicle behind an
access cover.
To remove the cover, pull the two tabs on the cover and
pull it off.

2-64
The air inflator kit is located in the glove compartment.
The kit includes a 22
-foot (6.7 m) hose with three
nozzle adapters.
To use the air inflator attach the appropriate nozzle
adapter to the end of the hose if required. Then attach
that end of the hose to the object you wish to inflate.
Attach the other end of the hose to the outlet.
Press and release the switch to turn the air inflator
on. The indicator light will remain on when the inflator
is running.
The system has an internal clock to prevent overheating.
The system will allow about five minutes of running
time, then the compressor will stop. The indicator light
will then begin to flash. When the indicator is off, the
inflator can be started again by pressing the switch. If
the compressor is still hot, it may only run for a short
time before shutting off again.Press and release the switch to turn the inflator off.
Place the inflator kit tools in the pouch and store it
properly. Remove the inflator hose from the outlet
during loading and unloading. Load leveling will not
function with the inflator hose attached to the inflator
outlet. See ªElectronically Controlled Air Suspension
Systemº in the Index.
To reinstall the cover, line up the tabs at the back of the
cover, put it in place and latch the tabs.
A continuous flashing indicator light may also indicate a
malfunction in the air suspension system. See
ªElectronically Controlled Air Suspension Systemº in
the Index.
CAUTION:
Inflating something too much can make it
explode, and you or others could be injured. Be
sure to read the inflator instructions, and inflate
any object only to its recommended pressure.

2-67
The light will be red in the event of an OnStar system
malfunction. If this occurs press the OnStar Services
button to attempt to contact an advisor. If the connection
is made, the advisor will assist you with steps to take to
make sure that the system is functioning properly. If you
cannot contact the advisor, take your vehicle to your
dealership as soon as possible for assistance.
Cellular Antenna
The cellular antenna on the outside of your vehicle is
critical to effective communications using the OnStar
system. Optimum cellular reception can be obtained
when the mast is straight up and down.
OnStar Services
The following services are available within OnStar
service plans. Your vehicle comes with a specific
one
-year service plan that allows use of some or all of
the following services.
Automatic Notification of Air Bag Deployment: If an
air bag deploys, a priority emergency signal is
automatically sent to the center. An advisor will locate
your vehicle's position, try to contact you and assist you
in the situation. If the center is unable to contact you, an
emergency service provider will be contacted.Stolen Vehicle Tracking: Call the center at
1
-888-4-ONSTAR (1-888-466-7827) to report your
vehicle stolen. The system can then attempt to locate
and track your vehicle and the advisor will assist the
proper authorities.
Roadside Assistance with Location: For vehicle
breakdowns, press the OnStar Services button. An
advisor will contact the appropriate help.
Remote Diagnostics: If an instrument panel light comes
on, press the OnStar Services button. An advisor can
perform a check of the engine on
-board computer, and
recommend what action needs to be taken.
OnStar MED
-NET: Med-Net can store your personal
medical history and provide it to emergency personnel if
necessary. (Requires activation and additional fee.)
Remote Door Unlock: To contact the center, call
1
-888-4-ONSTAR. You will be required to provide your
security information. An advisor will send a command
to your vehicle to unlock itself. The advisor can delay
unlocking your vehicle. Remote Door Unlock is
disabled 48 hours after the vehicle is parked to maintain
the battery charge.
Vehicle Locator Service: To contact the center, call
1
-888-4-ONSTAR. You will be required to provide your
security information. An advisor will send a command
to your vehicle to sound the horn and/or flash the lamps.

2-68
Route Support: An advisor can provide directions or
guidance to most places you want to go. In addition,
they can help you locate gas stations, rest areas, ATMs,
hospitals, hotels, stores, eateries and more.
Ride Assist: An advisor can locate transportation in the
event that you are unable to drive.
Concierge Services: The concierge advisor can obtain
tickets, reservations, or help with vacation/trip planning
and other unique items and services.
OnStar System Limitations
Complete limitations can be found on the Subscriber
Services Agreement. In order to provide you with
excellent service, calls with the OnStar Center may be
monitored or recorded.
OnStar Service is:

available in the 48 contiguous United States, Alaska,
Hawaii and Canada;

available when the vehicle is within the operating
range of a cellular provider;

subject to limitations caused by atmospheric
conditions, such as severe weather or topographical
conditions, such as mountainous terrain;

subject to cellular carrier equipment limitations.Global positioning locating capabilities will not be
available if satellite signals are obstructed.
OnStar will not function if the vehicle's battery is
discharged or disconnected. It may also be inoperative
if the vehicle is in an accident and the OnStar or vehicle
electrical system components are damaged.
OnStar is the communication link between you and
existing governmental emergency and roadside service
providers. OnStar will receive your call and use
reasonable effort to contact an appropriate provider.
OnStar cannot promise that the providers will respond
in a timely manner or at all.
Sunroof (Option)
Your vehicle may be equipped with a power sliding
sunroof. To open or close your sunroof, the ignition
or Retained Accessory Power (RAP) must be active.
See ªRetained Accessory Powerº in the Index.
Press and release the back of the button in the overhead
console to open the sunroof. You can press the front
of the button to close the sunroof. Once the sunroof is
closed, press the forward side of the button to open the
sunroof to the vent position.
The sunroof is also equipped with a sunshade which you
can pull forward to block sun rays.

2-81
Anti-Lock Brake System Warning Light
With the anti-lock brake
system, this light will
come on when you start
your engine and may stay
on for several seconds.
That's normal.
If the light stays on, or comes on when you're driving,
your vehicle needs service. If the regular brake system
warning light isn't on, you still have brakes, but you
don't have anti
-lock brakes. If the regular brake system
warning light is also on, you don't have anti
-lock brakes
and there's a problem with your regular brakes. See
ªBrake System Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
Engine Coolant Temperature Gage
United States Canada
This gage shows the engine coolant temperature. If the
gage pointer moves into the red area, it means that your
engine coolant has overheated. If you have been
operating your vehicle under normal driving conditions,
you should pull off the road, stop your vehicle and turn
off the engine as soon as possible.
See ªEngine Overheatingº in the Index for
more information.

2-87
Change Engine Oil Light
United States Canada
This light is displayed when the engine oil needs to
be changed.
Once the engine oil has been changed, the CHANGE
ENG OIL light must be reset. Until it is reset, the light
will be displayed when the engine is on. For more
information on resetting the system, see ªOil Life
Systemº in the Index.
Security Light
United States Canada
This light will come on briefly when you turn the
key toward START. The light will stay on until the
engine starts.
If the light flashes, the Passlock

system has entered a
tamper mode. If the vehicle fails to start, see ªPasslockº
in the Index.
If the light comes on continuously while driving and
stays on, there may be a problem with the Passlock
system. Your vehicle will not be protected by Passlock,
and you should see your dealer.
Also, see ªContent Theft
-Deterrentº in the Index for
additional information regarding the SECURITY light.

2-94
GM Oil Life System

Press the fuel information button until ENGINE OIL
LIFE appears in the display. The GM Oil Life System

shows an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after an oil
change. It will alert you to change your oil on a schedule
consistent with your driving conditions.
Always reset the engine oil life after an oil change.
To reset the Oil Life System press and hold the select
button while ENGINE OIL LIFE is displayed.
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule
in this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. Also, the oil change reminder does not
measure how much oil you have in your engine. So, be
sure to check your oil level often. See ªEngine Oilº in
the Index.Personalization Button
You can program certain features to a preferred setting
for up to two people. Press the personalization button
to scroll through the following personalization features.
All of the personalization options may not be available
on your vehicle. Only the options available will be
displayed on your DIC.

ALARM WARNING TYPE

AUTOMATIC LOCKING

AUTOMATIC UNLOCKING

SEAT POSITION RECALL (If Equipped)

PERIMETER LIGHTING

REMOTE LOCK FEEDBACK

REMOTE UNLOCK FEEDBACK

HEADLAMPS ON AT EXIT

TILT MIRROR IN REVERSE (If Equipped)

EASY EXIT SEAT (If Equipped)

DISPLAY UNITS (E/M)

DISPLAY LANGUAGE
The driver's preferences are recalled by pressing the
unlock button on the remote keyless entry transmitter
or by pressing the appropriate memory button 1 or 2
located on the driver's door.

2-95
Alarm Warning Type
Press the personalization button until ALARM
WARNING TYPE appears in the display. To select your
personalization for alarm warning type, press the select
button while ALARM WARNING TYPE is displayed
on the DIC. Pressing the select button will scroll
through the following choices:

ALARM WARNING: BOTH (default)

ALARM WARNING: OFF

ALARM WARNING: HORN

ALARM WARNING: LAMPS
If you choose BOTH, the headlamps will flash and the
horn will chirp when the alarm is active.
If you choose OFF, there will be no alarm warning
on activation.
If you choose HORN, the horn will chirp when the
alarm is active.
If you choose LAMPS, the headlamps will flash when
the alarm is active.
Choose one of the four options and press the
personalization button while it is displayed on the DIC
to select it and move on to the next feature. For more
information on alarm warning type see ªContent
Theft
-Deterrentº in the Index.Automatic Locking
Press the personalization button until AUTOMATIC
LOCKING appears in the display. To select your
personalization for automatic locking, press the select
button while AUTOMATIC LOCKING is displayed on
the DIC. Pressing the select button will scroll through
the following choices:

LOCK DOORS OUT OF PARK (default)

LOCK DOORS MANUALLY

LOCK DOORS WITH SPEED
If you choose for the doors to lock out of park, the doors
will lock when the vehicle is shifted out of PARK (P).
If you choose for the doors to lock manually, the doors
will not be locked automatically.
If you choose for the doors to lock with speed, the
doors will lock when the vehicle speed is above 8 mph
(13 km/h) for three seconds.
Choose one of the three options and press the
personalization button while it is displayed on the DIC
to select it and move on to the next feature. For more
information on automatic door locks see ªProgrammable
Automatic Door Locksº in the Index.

2-96
Automatic Unlocking
Press the personalization button until AUTOMATIC
UNLOCKING appears in the display. To select your
personalization for automatic unlocking, press the select
button while AUTOMATIC UNLOCKING is displayed
on the DIC. Pressing the select button will scroll
through the following choices:

UNLOCK ALL IN PARK (default)

UNLOCK ALL AT KEY OUT

UNLOCK DOORS MANUALLY

UNLOCK DRIVER IN PARK
If you choose for all the doors to unlock in park,
all of the doors will unlock when the vehicle is shifted
into PARK (P).
If you choose for all the doors to unlock at key out,
all of the doors will unlock when the key is taken out
of the ignition.
If you choose for the doors to unlock manually,
the doors will not be unlocked automatically.
If you choose for the driver's door to unlock in park,
the driver's door will be unlocked when the vehicle is
shifted into PARK (P).Choose one of the four options and press the
personalization button while it is displayed on the DIC
to select it and move on to the next feature. For more
information on automatic door locks see ªProgrammable
Automatic Door Locksº in the Index.
Seat Position Recall (If Equipped)
Press the personalization button until SEAT POSITION
RECALL appears in the display. To select your
personalization for seat position recall, press the select
button while SEAT POSITION RECALL is displayed
on the DIC. Pressing the select button will scroll
through the following choices:

SEAT POSITION RECALL OFF (default)

SEAT POSITION RECALL AT KEY IN

SEAT POSITION RECALL ON REMOTE
If you choose seat recall off, the memory seat position
you saved will only be recalled when the memory
button 1 or 2 is pressed.
If you choose seat recall at key in, the memory seat
position you saved will be recalled when you put the key
in the ignition.