tow GMC JIMMY 1997 User Guide

Shifting Into PARK (P) (Automatic
Transmission
Models Only)
It can be dangerous to get out of your vehicle if
the shift lever
is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
If you have left the engine running, the vehicle can
move suddenly. You or others could be injured.
To be sure your vehicle won’t move, even when
you’re on fairly level ground, use the steps that
follow. If you have four-wheel drive with a manual
transfer case shift
lever and your transfer case is
in NEUTRAL (N), your vehicle will be free to roll,
even if your shift lever is in PARK (P). So, be sure
the transfer case is in
a drive gear -- not in
NEUTRAL
(N). If you’re pulling a trailer, see
“Towing a Trailer” in the Index.
Column Shift Lever
1. Hold the brake pedal down with your right foot and
set the parking brakc.
2. Move the shift lever into PARK (P) position like this:
2-30

0 Move the lever up as far as it will go.
3. If you have four-wheel drive with a manual transfer
case shift lever-. be sure the transfer case is in a drive
gear
-- not in NEUTRAL (N).
4. Turn the ignition key to LOCK.
5. Retnove the key and take it with you. If you can
leave your vehicle with the key, your vehicle is in
PARK (P).
Console Shift Lever
1. Hold the brake pedal down with your right foot and
set the parking brake.
2. Move the shift lever into PARK (P) position like this:
0 Hold in the button on the lever.
0 Push the lever all the way toward the front of
the vehicle.
3. Turn the ignition key to LOCK.
4. Remove the key and take it with you. If you can leave
your vehicle with the key. your vehicle
is in PARK (P).
2-31

Leaving Your Vehicle With the Engine
Running (Automatic Transmission
Models Only)
It can be dangerous to leave your vehicle with the
engine running. Your vehicle could move suddenlJ
if the shift lever
is not fully in PARK (P) with the
parking brake firmly set. If you have four-wheel
drive with
a manual transfer case shift lever and
your transfer case
is in NEUTRAL (N), your
vehicle will
be free to roll, even if your shift lever
is in
PARK (P). So be sure the transfer case is in a
drive gear
-- not in NEUTRAL (N). And, if you
leave the vehicle with the engine running, it could
overheat and even catch fire. You or others could
be injured. Don't leave
your vehicle with the
engine running unless you have to.
If you have to leave your vehicle with the engine
running, be sure your vehicle
is in PARK (P) and yo~~r parking brake
is firmly set before you leave
it. After
you've moved the shift lever into the PARK
(P)
position, hold the regular brake pedal down. Then, see
if you can move the shift lever away from PARK (P)
without first pulling it toward you (or pressing the
button on
a console shift lever). If YOLI can, it means that
the shift lever wasn't fully locked
into PARK (P).
Torque Lock (Automatic Transmission)
If you are parking on a hill and you don't shift your
transmission into PARK
(P) properly, the weight of the
vehicle may put too much force
on the parking pawl in the
transmission. You may find it difficult to pull the shift
lever out
of PARK (P). This is called "torque lock." To
prevent torque lock, set the parking br'ke and then shift
into PARK
(P) properly before you leave the driver's seat.
To find out how, see "Shifting Into PARK (P)" in
the Index.
When
you are ready to drive, move the shift lever out of
PARK (P) kc$~w you release the parking brake.
IF torque lock does occur. you may need to have another
vehicle push yours
a little uphill to take some of the
pressure from
the parking pawl in the transmission, so
~OLI can pull the shift lever out of PARK (P).
2-32

Shifting Out of PARK (P)
(Automatic Transmission)
Your vehicle has a brake-transmission shift interlock.
YOLI have to fully apply your regular brake before you
can shift
from PARK (PI when the ignition is in the
RUN position. See "Automatic Transmission Operation"
in the Index.
If you cannot shift out of PARK (P)? ease pressure on
the shift lever
-- push the shift lever all the way into
PARK (P) as you maintain brake application. Then
move the shift lever into the gear you want (you must
press the shift lever button
if you have the console
shift lever).
If you ever hold the brake pedal down but still can't
shift out
of PARK (P)? try this:
1. Turn the key to OFF.
2. Apply and hold the brake until the end of Step 3.
3. Shift to NEUTRAL (N).
4. Start the vehicle and then shift to the drive gear
you want.
5. Have the vehicle fixed as soon as you can.
Parking Your Vehicle (Manual
Transmission Models Only)
Before you get out of your vehicle, turn off your engine,
put your- manual transmission in REVERSE (R) and
firmly apply the parking brake.
If you have four-wheel drive with it manual transfer case
shift lever, be sure your transfer case is in a drive gear.
Your vehicle could roll
if it isn't.
If you are parking on a hill. or if your vehicle is pulling
a trailer, see "Towing a Trailer" in the Index.
2-33

Running Your Engine While You’re
Parked (Automatic Transmission)
It’s better not to park with the engine running. But if
ever have to, here are some things to know.
Idling the engine with the air system control
off could allow dangerous exhaust into
your vehicle (see the earlier Caution under
“Engine Exhaust”).
Also, idling in a closed-in place can let deadly
carbon monoxide
(CO) into your vehicle even if
the fan switch is at the highest setting. One place
this can happen is a garage. Exhaust
-- with
CO -- can come in easily. NEVER park in a
garage with the engine running.
Another closed-in place can be
a blizzard.
l (See “Blizzard” in the Index.)
I-
It can be dangerous to get out of your vehicle if
the shift lever is not fully in
PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don’t leave your vehicle when the engine is running unless you have to.
If you’ve left the
engine running, the vehicle can move suddenly.
You or others could be injured.
To be sure your
vehicle won’t move, even when you’re on fairly
level ground, always set your parking brake and
move the shift lever to
PARK (P).
If you have four-wheel drive with a manual transfer case
shift lever and your transfer case is in NEUTRAL
(N),
your vehicle will be free to roll, even if your shift lever
is in
PARK (P). So, be sure the transfer case is in a drive
gear
-- not in NEUTRAL (N). Always set your parking
brake. Follow the proper steps
to be sure your vehicle
won’t move. See “Shifting Into
PARK (P)” in the Index.
If you’re pulling a trailer, see “Towing a Trailer” in
the Index.
2-35

Tilt Wheel (If Equipped)
If you have the tilt steering
wheel,
you should adjust
the steering wheel before
you drive.
You can raise it to the highest level to give your legs
more
room when you enter and exit the vehicle.
To tilt the wheel, hold the steerins wheel and pull the
lever toward you. Move the steering wheel
to a
comfortable level. then release the lever to lock the
wheel in place.
Do not ad-just the steering wheel while driving.
Turn Signal/Multifunction Lever
The lever on the left. side of the steering column
includes your:
Turn Signal and Lane Change Indicator
Headlamp HighLow Beam Changer
0 Windshield Wipers
0 Windshield Washer
2-38 -

Turn and Lane Change Signals
The turn signal has twio upward (for right) and two
downward (for left) positions. These positions allow
you
to signal a turn or LI lane change.
To signal a tum, move the lever all the way up or down.
When the turn is finished. the lever will return automatically.\

An arrow on the instrument
panel will flash
in the
direction
of the turn
or lane change.
To signal a lane change, just raise or lower the lever
unt.il the arrow starts to flash. Hold it there until you
complete
your lane change. The lever will return by
itself when
you release it.
As you signal a turn or a lane change, if the arrows don't
flash but just stay
on, a signal bulb may be burned out
and other drivers won't see your turn signal.
If a bulb is burned out, replace it to help ac.oid an
accident.
If the arrows don't go on at all when you
signal
a turn, check the fuse (see "Fuses and Circuit
Breakers"
in the Index) and for burned-out bulbs.
If you have a trailer towing option with added wiring for
the trailer lamps.
a different turn signal flasher is used.
With this flasher installed, the signal indicator will flash
even
if ;I turn signal bulb is burned out. Check the front
and rear turn signal
lamps regularly to make sure they
are working.
Headlamp HighLow Beam Changer
To change the headlamps from low-beam to high or
high
to low. pull the multifunction lever all the way
toward you. Then release
it.
2-39

Press the tab under the mirror to reduce glare from
headlamps behind
you.
Outside Manual Adjust Mirror
Adjust your outside mirrors so you can just see the side
of your vehicle.
You can fold them before entering a car wash. Pull the
mirrors in toward the vehicle. Push the mirrors back out
when finished.
Power Remote Control Mirror
The control is located on the
driver’s door armrest.
Turn
the control to L or R to
choose the mirror, then
press the arrows on the
outside switch ring to adjust
the mirror.
2-49

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided into
two parts.
If one part isn’t working, the other part can
still work and stop you. For good braking, though, you
need both parts working well.
If the warning light comes on, there could be
a brake
problem. Have your brake system inspected right away.
I
This light should come on
briefly when you turn the
ignition key to RUN. If it
doesn’t come on then, BRAKE
(a) (@)
:;;::::$d;:n1::: if
have it fixed so it will be
If the light comes on while you are driving, pull off the
road and stop carefully. You may notice that the pedal is
harder to push. Or, the pedal may go closer to
the floor.
It may take longer to stop. If the light is still on, have the
vehicle towed for service. (See “Towing Your Vehicle“
in the Index.)
Your brake system may not be working properly
if the brake system warning light is on. Driving
with the brake system warning light on can lead
to an accident. If the light is still on after you’ve
pulled
off the road and stopped carefully, have
the vehicle towed for service.
When the ignition is on, the brake system warning light
will
also come on when you set your parking brake. The
light will stay on
if your parking brake doesn’t release
fully. If it stays on after your parking brake is fully
released,
it means you have a brake problem.
2-75

If the Light Is Flashing
The following may prevent more serious damage to
your vehicle:
Reducing vehicle speed.
Avoiding hard accelerations.
Avoiding steep uphill grades.
If you are towing a trailer. reduce the anlount of
cargo being hauled as soon as it is possible.
If the light stops flashing and remains
on steady. see “If
the Light Is On Steady” following.
If the light continues t.o flash, when it is safe to do so.
stop the \?el?ic&~. Find a safe place to park your vehiclc.
Turn the key off,
wait at least 10 seconds and restart the
engine.
If the light remains on steady, see “If the Light
Is On Steady” following. If the light is still flashing,
follow the previous steps, and drive the vehicle to your
dealer or qualified service center for service.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did
you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making s111-e to fully install
the cap. The diagnostic system can cleter~nine
if the fuel cap
has been left off
or improperly installed. A loose or
missing fuel cap
will allow fuel to evaporate into the
atmosphere.
A few driving trips with the cap properly
installed should turn
the light off,
Did you *just drive through a deep puddle of water’!
If so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out.
A few driving trips should turn the light off.
Have you recently changed brands of fuel?
I1 so, be sure to fuel your vehicle with cpality fuel (see
“Fuel”
in the Index). Poor fuel quality will cause your
engine not to
r11n as e,fficiently as designed. You may
notice this
as stalling after start-up, stalling when you put
the vehicle
into gear, mistlring, hesitation on acceleration
or
stumbling on acceleration. (These conditions may go
away once the engine is warmed up.) This will be detected
by the system and cause the light
to turn on.
If you experience one or more of these conditions,
change the fuel brand you use.
It will require at least one
full tank of the proper fuel to turn the light off.
If none of the above steps have made the light. turn off.
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment and
diagnostic
tools to fix any mechanical or electrical
problcnls that may have developed.