GMC YUKON 2006 User Guide

Heated Seats
If your vehicle has this
feature, the buttons are
located on the front doors.
The engine must be
running for the heated
seats to work.
To heat the entire seat, press the horizontal button
with the heated seat and seatback symbol. Press the
button to cycle through the temperature settings of
high, medium and low and to turn the heated seat off.
Indicator lights will be lit to designate the level of
heat selected: three for high, two for medium, and
one for low.To heat only the seatback, press the vertical button
with the heated seatback symbol. An indicator light on
the seatback button will be lit to designate that only
the seatback is being heated. Additional presses of the
seatback button will cycle through the heat levels for
the seatback only. Press the horizontal button again to
heat the whole seat.
The heated seats will be canceled after the ignition is
turned off. If you still want to use the heated seat feature
after you restart your vehicle, you will need to press
the heated seat button again.
1-5

Reclining Seatbacks
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there.
Always push and pull on the seatback to be
sure it is locked.
To adjust the seatback, lift the manual lever located
on the outboard side of the seat. Release the
lever to lock the seatback in the desired position.Lift the lever again without pushing on the seatback
and the seatback will go to an upright position.
If your vehicle has power seats with a power recliner,
seePower Seats on page 1-4for further information on
how to operate the reclining seatback feature.
1-6

{CAUTION:
Sitting in a reclined position when your vehicle
is in motion can be dangerous. Even if you
buckle up, your safety belts cannot do their
job when you are reclined like this.
The shoulder belt cannot do its job. In a crash,
you could go into it, receiving neck or other
injuries.
The lap belt cannot do its job either. In a crash
the belt could go up over your abdomen. The
belt forces would be there, not at your pelvic
bones. This could cause serious internal
injuries.
For proper protection when the vehicle is in
motion, have the seatback upright. Then sit
well back in the seat and wear your safety belt
properly.
Do not have a seatback reclined if your vehicle is moving.
Head Restraints
Adjust your head restraint so that the top of the restraint
is closest to the top of your head. This position reduces
the chance of a neck injury in a crash.
Pull the head restraint up to raise it. Push the head
restraint down to lower it.
Your rear seats may have head restraints that can be
adjusted up and down.
1-7

Rear Seats
Rear Seat Operation
Entering or Exiting the
Third Row Seats
Regular Models
If your vehicle has the 60/40 Split Bench seat in the
second row, you must ip and fold the second row seat
following the instructions later in this section. See60/40
Split Bench Seat (Second Row) on page 1-10. To exit
the third row seat with no assistance, do the following:
1. Reach over the second
row seat and pull up on
the strap loop located
in the center of the seat
where the seatback and
the seat cushion meet.
Then pull the seat
cushion up and push
it forward.
2. Next, push the seatback forward until it is at with
the oor.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there.
Always push and pull on the seatback to be
sure it is locked.
Return the seat to the normal seating position when
nished. Push and pull on the seatback to make sure it
is locked in place.
Extended Models
The passenger’s side of both the second row 60/40 split
bench seat and the second row bucket seat has an
easy entry/exit feature. This makes it easy to get in and
out of the third row seat.
1-8

To operate the easy entry seat, do the following:
1. Lift the release lever on the outboard side of the
back of the seat.
2. Tilt the seatback toward the front of the vehicle
and the seat will release.
3. Pull (push if you are exiting the third row with
no assistance) the seat forward until it stops.
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not provide
the protection needed in a crash. The person
wearing the belt could be seriously injured.
After raising the rear seatback, always check
to be sure that the safety belts are properly
routed and attached, and are not twisted.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there.
Always push and pull on the seatback to be
sure it is locked.
Return the seat to the normal seating position when
nished. Push and pull on the seatback to make sure
it is locked in place.
1-9

60/40 Split Bench Seat
(Second Row)
If your vehicle has a 60/40 split bench, the seats can
be ipped and folded for additional cargo space.
Flip and Fold Feature
To ip and fold the seat, do the following:
1. Make sure that there is nothing under or in front
of the seat.
2. Make sure that the headrests are completely
lowered or removed.
On regular models, the rear seatbacks may be
equipped with rearward folding headrests. When the
seatback is being folded forward, the head rest
will automatically fold rearward.On extended models, the headrests need to be
removed and stored. To do this, push the button at
the base of the head rest, and pull the head rest
out from the seatback. Slide the head rest pins into
the holes on the top of the seat cushion.
3. Pull up on the strap
loop located at the rear
of the seat cushion
and ip the seat
cushion forward.
1-10

4.Regular models:Push the seatback forward until
it is at.
Extended models:On the passenger side, lift the
lever at the base of the seat to release the seatback.
Push the seatback forward until it is at.
If the seatback cannot fold at because it interferes with
the cushion, try moving the front seat forward and/or
bring the front seatback more upright.Once the seatbacks are folded forward, on extended
models only, the rear seat footwell area will be exposed
and will have to be covered by the load oor panels.
To create a load oor, do the following:
1. Release the panels from the seatbacks by pushing
forward on the latches.
2. Fold the panels back to cover the rear seat
footwell area.
1-11

Returning the Seats to the Normal
Seating Position
To return the seat to the normal seating position,
do the following:
1. On extended models, lift the load oor panels and
latch them into the seatback.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there.
Always push and pull on the seatback to be
sure it is locked.
2. Lift the seatback up and push it rearward all
the way. Push and pull on the seatback to
make sure it is locked in place.
3. On regular models, return the headrests to the
upright position.
On extended models, return the headrests from
the stored position to the seatback.4. Lower the seat cushion until it latches into position.
Pull up on the seat cushion to make sure it is locked.
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not provide
the protection needed in a crash. The person
wearing the belt could be seriously injured.
After raising the rear seatback, always check
to be sure that the safety belts are properly
routed and attached, and are not twisted.
5. Make sure that the safety belt buckles on the
driver’s side seat are accessible to the outboard
and center occupants and are not under the
seat cushions.
1-12

50/50 Split Bench Seat
(Third Row)
If your vehicle has a 50/50 split bench seat, the
seatback(s) can be folded and the entire seat(s)
can be tilted, or removed from the vehicle.
Folding the Seatback(s)
To fold the seatback, do the following:
Pull up on the release lever labeled 1, located on
the rear of the seatback, and push the seatback
forward.
Unfolding the Seatback(s)
To return the seatback to the upright position,
do the following:
1. Pull up on the release lever labeled 1, located on
the rear of the seatback. Then pull up on seatback
until it locks into the upright position.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there.
Always push and pull on the seatback to be
sure it is locked.
2. Push and pull on the seatback to make sure
it is locked.
1-13

Tilting the 50/50 Split Bench Seat(s)
The seat(s) can be tilted forward for additional
cargo space.
To tilt the seat, do the following:
1. Open the liftgate to access the controls for the
50/50 seat.
2. Make sure the head restraints are completely
lowered.
3. Fold the seatbacks forward using the instructions
listed under “Folding the Seatbacks” previously.
You will not be able to unlatch the seat from
the oor unless the seatback is folded down.4. Unlatch the seat from the oor by pulling up on the
lever labeled 2, located next to the carrying handle
at the rear of the seat.
5. Lift the rear of the seat up from the oor.
6. Tilt the seat fully forward and lock it into place.
7. Push and pull on the seat.
Put the seat in this position only when necessary for
additional cargo space.
1-14