oil change GREAT WALL PEGASUS 2006 Owner's Manual

SA-30
5. Front hub bearing outer race inspection and change
(a) Check each bearing
Wash the inner and outer races of each bearing, and check
them whether they are wearied or damaged.
(b) Tear down the outer race of each bearing.
Tap out the bearing outer race with copper bar and
hammer.
Notice: bind the dismantled inner and outer races of
bearing together to prevent from mixing.
6. Front brake disc inspection and change
(a) Check the wear situation of front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
front brake disc.
(c) Connect the front wheel hub and front brake disc and
screw up the bolts with moment spanner to the specified
torque diagonally
Fastening torque
(70-80)N
m
(d) Conduct the dynamic balance test on the dynamic balancer,
the amplitude value displayed should not be above 13.5g
under the condition that the measuring rotating velocity
is 796 r/m and the locking rotating velocity 786 r/m,
otherwise, tap in the counter balanced clip, which is 4g
each, at the corresponding location, the number of the
clip should not be more than 4.
(e) Tap in the new bearing outer race with the special service
tool.
Notice: the inner and outer races of bearing should be
changed in set.
Assembly of Front Wheel Hub
1.Mount on the inner race and roller assembly of front hub
bearing (inner) as well as the front hub oil seal.
Coat the lithium base grease of 4 to 5 mm on the inside surface of
the bearing outer race and front wheel hub, and plaster the
lubricant in the front hub bearing (inner) and the roller assembly.
Coat a little lubricant on the lips of oil seal of front wheel hub, and
then tap the oil seal of front hub in place with special service tool.
Notice: do not coat the lubricant on the front brake disc face.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-46
5. Tear down the front hub, the oil seal and the inner race
of front hub bearing (inner)
(a) Prize out the oil seal.
(b) Take out the inner race of front hub bearing (inner).
6. Inspection on and change of the outer race of front hub
bearing
(a) Check each bearing:
Wash the inner and outer races of each bearing to check
their wear or damage situation.
(b) Tear down the outer race of each bearing:
Tap out the outer bearing race with copper bar and hammer.
Notice: bind the inner and outer races of the same
bearing together to prevent from mixing.
7. Inspection and change for front brake disc
(a) Check the wear situation of the front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
the front brake disc.
(c) Connect the front wheel hub and the front brake disc with
bolts, which are tightened diagonally with moment span-
ner according to the specified torque.
Fastening torque
(70-80)N
m
(d) Make the dynamic balance test on the dynamic balancer,
and the amplitude value displayed should not be smaller
than 13.5g under the condition that the measuring rotat-
ing velocity is 796 r/m and the locking rotating velocity
of 786 r/m, otherwise, tap the counter balanced clip,
which is 4g each, in the corresponding position, the clip
number should not be more than 4.
(e) Tap in the new bearing outer race carefully with the
special service tool.
Notice: the inner and outer races of the same bearing
should be changed in one time.
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-50
(c) Tear down the split pin and groove nut from the position
where the lower ball stud.
(d) Tear down the steering knuckle from the position where
the lower ball stud with the special service tool, and
(e) Press down the lower arm to tear down the steering
knuckle.
7. Tear down the Lower ball stud assembly from the posi-
tion where the steering knuckle locates.
Steering knuckle inspection and change
Inspection on and Change of Steering
knuckle
1. Check the steering knuckle
Check the steering knuckle with the dye penetration agent to
see weather has crack, if any crack is found, change the
steering knuckle.
2. Tear down the inner oil seal

drive shaft and the thrust
plate

steering knuckle.
Prize out the inner oil seal

drive shaft from the steering
knuckle with the screwdriver to take out the thrust plate


steering knuckle.
Suspension System and Automobile Axle(SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

SA-52
8. Mount the inner oil seal óon the steering knuckle.
Check the oil seal visually, if any deformation or glue lack is
found, change the oil seal
Mount of Steering Knuckle
1. Mount the lower ball stud on the steering knuckle;
Connect the lower ball stud and the steering knuckle with
bolts, and screw up the bolts according to the specified torque.
Fastening torque
(70-90)N
m
2. Mount on the steering knuckle
(a) Coat the lubricant HP-R on the drive shaft.
(b) Press down the lower arm to mount on the steering
knuckle.
(c) Mount on the groove nut of lower ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
(d) Mount on the groove nut of upper ball stud and screw up
the nut according to the specified torque, and then mount
on the split pin.
Fastening torque
(132-152)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Wheel Hub and Steering Knuckle (Steering Knuckle)

SA-57
1. Support up the front of vehicle to tear down the front
wheel and the steering knuckle.
2. Drain off lubricant in the front speed reducer.
3. Disconnect the front speed reducer flange and the drive
shaft.
Notice: Mark the assembly marks on the speed reducer
and the drive shaft before disconnecting them.
4. Tear down the front speed reducer.
5. Tear down the flange and dust cover:
(a) Loosen the riveted position on main-tooth nut with the
hammer and chisel.
Front Speed Reducer
Change of driving bevel gear oil seal of front speed reducer
front speed reducer and
differential assembly
oil-guard tray

driving bevel gear oil seal
flange and dust cover
140-210


Parts that cannot be reused after being used
specified torque
N
M
main-tooth nut
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

SA-58
(b) Lock the flange with special service tool to tear down the
main-tooth nut.
7. Tear down the inner race of conical roller bearing;
If the bearing is damaged, change a new bearing.
8. Mount the new bearing.
6. Tear down the driving bevel gear oil seal and oil-guard
tray:
(a) Tear down the driving bevel gear oil seal with special
service tool.
(b) Tear down the oil-guard tray. (c) Tap down the flange and dust cover with copper bar.
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

SA-59
12. Rivet the main-tooth nut.
10. Mount the flange and dust cover:
(a) Encase the flange and dust cover in the front speed
reducer shell through the clinch of oil seal.
(b) Lock the flange with the special service tool and screw up
the nuts according to the specified torque.
Fastening torque
(140-210)N
m
11. Adjust the preload of driving bevel gear bearing
Measure the play preload between the driving bevel gear and
the driven bevel gear with the torque tester.
Preload:(1.8-2.4)N
m
Remark: if the requirement is not satisfied, change the
adjusting washer between the adjusting washer jackets and
bearing 32307, see the disassembly and assembly for front
speed reducer, until the requirement is satisfied.
(a) If the preload is larger than the specified value, change
with a thicker adjusting washer;
(b) If the preload is smaller than the specified value,
change with a thinner adjusting washer.
9. Mount the new driving bevel gear oil seal:
(a) Encase the oil-guard tray.
(b) Press the new oil seal in the speed reducer shell with the
special service tool; the mounted oil seal should be 1.5
mm away from the end face of the housing.
Notice: Coat the lithium base grease evenly on the lips of
oil seal.


Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

SA-60
13. Mount the front speed reducer assembly on the frame.
14. Connect the drive shaft to the flange:
(a) Align the assembly mark and then connect the drive
shaft and the front drive axle flange with four sets of
bolt and nut.
(b) Screw up the nuts according to the specified torque.
Specified torque
(69-79)N
m
Suspension System and Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Driving Bevel Gear Oil Seal of Front Speed Reducer)

SA-63
1. Tear down the front long semi-axis and the front minor
half-shaft
Pull out the front long and minor semi-axis from the front
speed reducer with tool.
2. Tear down the front drive axle shaft sleeve and screw off
the bolts connecting the half-shaft sleeve.
3. Tear down the oil seal - front half-shaft:
Tear down the oil seal-front half-shaft with the special service
tool.
Change of Axle Shaft Oil Seal

snapping ring
front minor half-shaft
front speed reducer and differential

oil seal-front half-shaft
front long
semi-axis

snapping ring
88
N
M
specified torque

Parts that cannot be reused after being used)
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Axle Shaft Oil Seal)

SA-64
5. Mount on the upper front drive axle shaft sleeve,
Coat the bolt thread with thread locking agent.
Fastening torque
88N
m 4. Mount on the new oil seal-front half-shaft:
Press in the new oil seal with the special service tool until it
flush with the outer ending of the oil seal, coat moderate
lubricant on the lips of the oil seal.
6. Mount on the front long semi-axis and the front minor
half-shaft.
(a) Mount the new snapping ring on the half-shaft.
(b) Mount on the long semi-axis and the minor half-shaft
with the special service tool.
Suspension System Automobile Axle (SF/4WD)
Front Speed Reducer (Change of Axle Shaft Oil Seal)