torque GREAT WALL SAILOR 2006 User Guide

MT-34Gearbox
Rear Housing Assembly (Inspection On and Change of The Component Elements of Position-Limit Mechanism)
Inspection on and change of the component
elements of position-limit mechanism
1. Tear down the component elements of position-limit
mechanism
(a) Dismantle the bolts with the torque socket spanner.
(b) Punch out the spring cylindrical pin with the drift punch
and hammer.
(c) Tear the component elements of position-limit mechanism
down.
2. Check the component element of position-limit mechanism.
Run and propel the limit stop and the limit stop can return
to the original location automatically, otherwise, change the
limit stop.
3.
Mount the component element of position-limit mechanism
(a) Mount the component elements of position-limit mecha-
nism in the rear housing.
(b) Tap the spring cylindrical pins in with drift punch and
hammer as shown in the drawing.

MT-35Gearbox
Rear Housing Assembly (Inspection On and Change of The Component Elements of Position-Limit Mechanism)
(c) Coat the sealing agent on the bolt thread.
(d) Propel the plug with the torque socket spanner.

MT-38Gearbox
Assembly of Gearbox
(b) Mount the intermediate-gear shaft in the central link
plate, and mount the backup rear bearing with SST while
holding the intermediate-gear shaft.
4. Mount the baffle of rear bearing of output shaft
Mount and propel the bolts with torque socket spanner.
Tightening moment

Tang tooth
(17
22)N
m
Upper tooth
(12
17)N
m
5. Mount the reverse idle gear and shaft
(a) Mount the reverse idle gear and shaft.
(b) Mount the axial pressing plate of the reverse idle gear,
and then propel the bolts tightly.
Tightening moment
(15
20)N
m
6. Mount the bracket cluster of reverse rocker arm
Mount the reverse rocker arm bracket and propel the two bolts
tightly.
SST

MT-44
sealed material
Gearbox
Assembly of Gearbox
17. Mount the steel ball, locating spring and locating spring
plug
(a) Mount the steel ball and locating spring.
Remarks:
Mount the short spring at the bottom of the central link plate.
(b) Coat the sealing agent on the plug thread.
(c) Mount the plug and tighten them with the torque socket
spanner.
Tightening moment
(17
22)N
m
18. Tear down the central link plate from the table vice
(a) Tear down central link plate from the table vice.
(b) Dismantle the bolts, nuts and washers
19. Mount the gearbox frame
(a) Coat the sealing material on the coupling face of the
gearbox frame as shown in the drawing.
(b) Put down the central link plate straightly as shown in the
drawing.
(c) Mount the gearbox frame on the central link plate as
shown in the drawing.

TF-3Transfer Box
Troubleshooting
Common troubles Causes Resolving approaches
Change the lubricant or supplement the
lubricant volume.
Guarantee the torque of all connecting
elements stand at the specified value.
Open the transfer case to check the
bearing and othe parts whether is weared
or daamaged,if this happened,change
the parts.
Difficulty in mechanic gearshift or
outplace gear engagement
Troubleshooting
Incorrect lubricant or insufficient
lubricant volume.
Looseness of connecting bolt or other
connecting element.
Noise from the transfer box bearing Noise, which is spreader by the transfer
box instead of clutch, engine, drive shaft
and other parts, occurs in each speed. No driving of front wheel in the four-
gear engagementDrive chain breakDisassemble and check the damage of
inner parts, and change the chain. Adjust or repair shift lever.Open the
transfer box to check the toggle fork and
guide shaft, and change the parts as
requirement.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts.Open
the transfer box to check whether the
parts is wearied or not, and, if any, change
the weary parts.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts. Overlarge loose fit clearance of the
shift toggle fork on the shift guide
shaft.
Wear of the shift toggle fork
assembly including pin and contact
roller.
Wear of the shift cam hub and the
liner.
Attainment of coupling gear Mechanic gearshift seizing at a certain
location Engagement failure of the mechanically
shift transfer boxDamage or unsuitable adjustment of
the shifting mechanism.
Damage or serious wear of the inner
shifting parts, or looseness or
attainment of the shift toggle fork
assembly on the guide shaft.
Unsuitable adjustment of shift lever.Adjust or repair the shift lever mechanism.
Change the seriously wearied parts.
Change the loose or weary parts. Refer to the vehicle manual for correct
operation.
Add the specified oil of given volume.
Open the rear cover of transfer box to check
and changer the damaged parts.
Open the rear cover of the transfer box to
check whether the sliding parts can slide
freely along the axle, if not, dismantle it and
change the damaged parts. Incorrect operation.
Lubricant of inferior quality or
insufficient volume.
Adhesive bonding of shift toggle fork.
Adhesive bonding of the sliding joint
cover, locking sleeve or gear. Mechanic gearshift failure under the
movement of shifting handleBreak or damage of the shift rocker
arm or shift lever.
Damage of the guide plate of shifting
cam;Change the damaged element.
Open the rear cover of the transfer box to
check the damaged element and change
it. Electric gearshift troubleDamage or failure of electrically
controlled element, electric module,
speed sensor, electric motor, electric
clutch, or built-in wire harness.
Damage or worn of shifting cam,
joint cover, locking sleeve, toggle
fork or shift guide axle.Adhesive
bonding shiftRefer to the vehicle usage manual to
diagnose the failure element and change
it as requirement.
Dismantle the weary or damaged parts
and change it as requirement.
Dismantle and check the free movement
of sliding element, and change it as
requirement

TF-8Transfer Box
Disassembly and Mount of Transfer Box
2. Transfer box mount
a) Coat the lubricant grease on the output axial
spline of the gearbox with a thin sleeve contain-
ing lubricant grease.
b) Mount a new gasket on the mounting face of the
transfer box.
c) Lift the lifting bracket of transfer box and align
it to the same axle with the gearbox.
Notice: The transfer shall be guaranteed to flush
with the gearbox before connecting the spline.
Do not handle it forcefully to press the transfer
box spline into the gearbox. Otherwise, damage
will be caused, run the rear output shaft where
necessary to aim at the spline.
(d) Move the transfer box forward slowly so that
the spline and pin of the input shaft of gearbox
reach the front body of the transfer box, and the
gasket attaches on the gearbox completely.
(e) Ensure that the mounting holes of the front
body of transfer box, gasket, and gearbox are in
alignment and then mount the sets of bolt and
nut.
Fastening torque
(35-48)N
m
(f) Connect the rear drive shaft and the rear output
flange of the transfer box.
(g) Connect the front drive shaft and the front
output fork flange of the transfer box.(h) Connect the venting valve and the soft ventila-
tion pipe.
(i) Connect the cables of odometer that locates
nearby the transfer box.
(j) Connect all wire harnesses that connected with
the transfer box, and
(k) Add the lubricant of right brand.
Notice: when starting the engine, if the lubricant
is added incorrectly or in unsuitable volume,
which may lead the transfer box to damage.
Notice: as for the transfer box mounted on
vehicle, oil pump shall be used when adding oil
for it.
Notice: In case the transfer box is taken apart for
maintenance or inspection, there will be no
lubricant supplied by oil pump in the oil passage
on the top of transfer box. Therefore, it is not
accurate to control the oil volume by opening the
oil filling plug, in such condition, the oil passage
will be filled with oil once the oil pump runs. If the
wheel can run, such operation can be conducted
on the lifting jack. The oil level shall be rechecked
once the oil pump runs.
(l) Put down the vehicle after finishing the lubri-
cant inspection, and connect the cell cathode.

TF-9
5 4
3
1
6 2
1. rear body of transfer box
2. flange
3. oil seal
1. sensor bracket
2. bolt
3. speed sensor
4. o-ring
5. sensor assembly
6. bolt
7. gasket
8. rear body of transfer box2 1
5 3
4
4
6
7
8
Transfer Box
Disassembly of Transfer Box
4. gasket
5. nut
6. oil plug
Disassembly of Transfer Box
1. Brief instruction
In case the transfer box is required to be repaired for the
damaged specific element, it shall be taken apart to the degree
on which the damaged element is taken out. And the parts
taken apart from the transfer box, if it doesnít include the
damage element, can exist in the form of sub-assembly or
group instead the individual form, otherwise, the parts will be
taken apart individually.
2. Transfer Box Disassembly
Put the transfer box on the worktable and ensure the rear part
or the rear cover faces upward. Put the wooden block under the
front part of transfer box to keep the transfer box stands
horizontally. The disassembly process is as follows:
(a) Fasten the flange with the torque arm typed T-13-54-
002, screw off the nut to take down the gasket, then take
apart the flange and oil seal.
(b) Take down the two oil plugs from the transfer box body.
As for the electric gearshift transfer box, tear down the
electric shifting element according to the following
disassembly approach:
(a) Tear down the three bolts, gaskets, sensor and clip for
wire harness.
(b) Tear down the sensor assembly and take apart the O-
ring.
(c) Tear down the motor assembly.

TF-12
110
9
8
6
5
4
3
2
11
15
14
13
12
17
18
19
207
16
Transfer Box
Disassembly of Transfer Box
1. fork-type flange
2. dust cover
3. fork-type flange assembly
4. transfer box front housing
8. Take apart the following parts from the remaining trans-
fer box housing assembly
(a) Fasten the front fork-type flange with the torque arm of
T-13-54-002 and screw off the nuts to take apart the
gasket, pull out the front fork-type flange assembly and
sealing ring.
(b) The dust cover may also be pressed down from the front
fork-type flange where necessary, and
(c) Take apart the front output shaft.
1. planetary mechanism
assembly
2. gasket
3. snapping ring
4. thrust disc
5. sun wheel
6. planetary bracket
7. input shaft assembly
8. input shaft
9. needle bearing
10. bearing shell
11. transfer box front
body assembly
9. Tear down the front body, input shaft assembly and
planetary mechanism assembly
Tear down the following parts from the remaining transfer box
housing assembly
(a) Take apart the venting valve.
(b) Take apart the six bolts to separate the front body from
the transfer box housing and take down the front body
(take notice not to damage the front-end cover and the
transfer housing).
(c) Take apart the front body assembly, input shaft assembly
and planetary mechanism assembly in grouping manner
(loose the snapping ring to take apart the input shaft from
the front end cover).
(d) Hold one end of the input shaft on the worktable while
open the long end of the snapping ring, press the front
body tightly to disassemble the front body assembly from
the remaining assembly.
(e) Take apart the snapping ring and oil seal from the front
body, the pin is only be taken apart where change is
necessary.
(f) Take apart the bearing and gasket from the input shaft
assembly after the bearing gripping loop is taken apart;
and take apart the input shaft assembly from the planetary
mechanism assembly.
(g) Take apart the needle bearing and bearing shell from the
input shaft assembly, and
(h) Take apart the snapping ring, thrust disc and sun wheel
from the planetary assembly, and
(i) Do not try to disassemble the planetary bracket.
4
2
1
5 6
7
83
5. front output shaft
6. oil seal
7. washer
8. nut
12. oil seal
13. locating pin
14. transfer box front
body
15. snapping ring
16. transfer box front
housing
17. bearing
18. bearing gripping
loop
19. bolt
20. vent

TF-14
7
6
5
4
3
21
1. transfer box front housing assembly
2. gear ring
3. oil seal
4. transfer box front housing
5. locating pin
6. ball bearing
7. snapping ring
NMR23
41
1. oil seal
2. transfer box front housing
3. gear ring
4. locating pin
Transfer Box
Transfer Box Assembly
Transfer box assembly
1. Introduction
Please refer to the given instruction of this chapter during
assembly process. And the following items shall be taken
notice on:
(a) In case that the torque of the threaded parts is required,
torque spanner shall be used to screw up the parts.
(b) The small parts shall be coated with the lubricant grease
during the mounting process, so that they are immobilized
at the mounting locations.
(c) SST such as thimble of T-13-54-001 shall be used to press
the oil seal and bearing during the oil seal mount and
bearing mount, do not use the hammer to strike the oil seal
or bearing directly.
2. Lubricating during assembling
All inner parts without lubricant shall be lubricated with the
suitable lubricant before mounting, so that they can be as-
sembled easily and can supply the original lubricant
performance.
(a) If the O-ring and oil seal were not lubricated before
mounting, they may be damaged.
(b) Be sure that the bearing or liner is lubricated completely
before mounting. Because the bearing or liner may be
leaded into damage even though they are run for a very
short time.
(c) The lips of oil seal and the metal elements that match with
lips shall be lubricated before mounting.
3. Transfer box housing assembly
Parts taken apart from the transfer box shall be mounted
according to the following approaches:
(a) If the gear ring needs to be changed, the tooth-type saddle
rear of new gear ring shall be flushed with the gullet of the
transfer box front housing when pressing the new gear
ring. Press in the gear ring as shown in the left bottom
drawing, in which, the chamfering end is firstly pressed
in. if it is ensured the gear ring is not tilted, then fasten the
gear ring tightly on the housing.
(b) In case there are two locating pins taken apart, mount two
new locating pins into the housing.
(c) Press the bearing into the transfer box front housing and
mount the snapping ring correctly, and
(d) Put down the new oil seal as shown in the left bottom
drawing and press it into the housing.

TF-17
1.25-1.75mm
23
1
12.70mm
13
2
4
4
2
1
5 6
7
83
(e) In the case that the input shaft is taken apart, what need
to do is to fill the needle bearing as shown in the drawing
and press it in the input shaft, meanwhile, press the new
sliding bearing to complete the whole input shaft assembly.
(f) Raise the planetary mechanism assembly to mount it into
the input shaft assembly; encase the thrust gasket and
press in the bearing through the input shaft end. Encase
the fixed bearing in the snapping ring groove of the input
shaft with a snapping ring.
(g) If the transfer box front body is taken apart, press the new
located pin in the front body, and the pressing dimensions
are shown in the drawing.
(h) Put down the oil seal as the drawing shows, and press it
in the front body according to the dimensions shown in
the drawing.
(i) Put down the front body assembly on two wooden blocks
in the way that the coupling face of the front body and the
housing faces upward, so that there is clearance left
between the input shaft assembly and the worktable. Put
down the input shaft and planetary mechanism assembly
in the front body, in which the input shaft shall be
downward. Open the long ends of the snapping ring to
encase input shaft and planetary mechanism assembly
until the snapping ring enters into the external snapping
ring groove of the bearing.
(j) Coat the sealing glue of 1.6mm on the coupling locations
of the front end cover and transfer box assembly, The
glue shall be coated continuously without break and steer
clear of the screwed hole.
(k) Screw up the six bolts.
Fastening torque
(27
46)N
m
6. Assembly of front output shaft
Mount the following parts:
(a) If the dust cover is taken apart, mount it by pressing.
(b) Encase the input shaft, sealing ring, gasket and nuts in the
transfer front housing.
(c) Insert the torque arm of T-13-54-002 in the flange hole to
screw up the nuts.
Fastening torque
(203
244)N
m Transfer Box
Transfer Box Assembly
1. needle bearing
2. bearing roller
3. input shaft
1. locating pin
2. oil seal
3. front body of transfer box
4. snapping ring
1. fork-type flange
2. dust cover
3. fork-type flange assembly
4. transfer box housing5. output shaft
6. oil seal
7. washer
8. nut