Connector view HONDA CIVIC 1999 6.G User Guide

Page 340 of 2189

c l16cl10c115
Different wires with the same color have b6en given a number suffix to distinguish them (for example, YEUBLKl
and YEUBLK'are not the same).
O: Related to Fuel and Emissions System.
c123
ffi
c11a
@
cl20
..+, 1
l+'.1'+:l
c109
r'ft]
flofr-N _-l
ItIYEUBLK, IIEIBLvBLU' I
c141
ffi
16T Lr cRN^/v-H;l
161-BrxtEL-__l
c11E tA/Tl
l- l,l
lOlGBN, I
f6lBr-r,--l
clr7
F1ftr
@fBLK-_-lI a BLKTYEL I
|ol-Balro/Hl -l
c121lAtfl
l- lrl
McnN/BLK' I
f4tEr-- __-l
c125
rfrr
Etr
I t lwHri REo' IItrIRED/YEL, _-l
blBLK Ea -l
ftl BLK^tHi'l
- Connector with male terminals (double outlinel: View from terminal side
- Connector with female terminals (single outlin€): View from wire side
NOTE: .
a
a(cont'd)
11-71
o8TK?YEL.!lGBN/8TKI2BLICYELoGffN/8TK1BLK/YEL@GNN/aLK?
(tBLfiELoGRN/BLKBLK/YEI12BLKJ^/EL!3GRN/BLX'8LK/YELGRN/BLK'
c128 (A/Tl
_El-
I'l ,l
IOIBLUryEI' I
161-crNalrHr' -l
(xlsarr
Ftr.T
l6ELffiHr-]
tr18!( -___-l
lglcRN/REp I
c12t l[lTl
ffi
EIWHF
_l
l(?lREp, I
c126 lA/Tl
fr
EIwHI-__-ll€) lFEp5 I
c352c351

Page 342 of 2189

c105
ffi
C10,1(Canadal
I rlz 3l
16lwHrsEo. -l
I2 BLK/YEL IftlwHri BLUIl'l
cl t3
D
c123
ffil3 4l
c104
l1 2l
l-f.l
c102
F1+..rl1 2 3l
ffl'wHnr€D" --.l
ItrERlxBLa__llo."llBurntotl-l
c101
C11il
ffi
c137
a
c108
ffi
c107
ffi
c106
ffi
c302
tu
c138
A
v
FTBtKiBLtr__llZTYEuBLKi l
NOTE: oDifferent wires with the same color have been given a number suffix to distinguish them (for example, YEUBLKl
and YEUBLK'are not the same).
O: Related to Fuel and Emissions Svstem.a
(cont'd)
11-73
- Connector with male terminals (double outline): View from terminal side
- Connector with female terminals (single outline): View from wire side
.1'BLKYEL6WHT/BLU
eBLKI1YEUGRN
3YEUREO89BLKryVFT5lYEUBLKI10BLK,ryEL
BLK^/EL:d)GBN/BLK'2BLK/YELGRN/8LK'3BLK,YELGRN/BLK'rljGRN/BLK'ELKTYEL12BLI(YELrtGFN/BLK'!l

Page 344 of 2189

c122
A,g
l-iln'eo*r,vHr__-ll[lcRNiBLitl]l
cl17
r'trTl
16lBLK,-__-llO BLX,\,E[ |
16l Btu/wil-
c112
ffi
Cliro
o
C1'11
ffi
l6l-ciN/YEL' _-l
NOTE: . Different wires with the same color have been given a number suffix to distinguish them (for example, YEUBLK1
and YEUBLK'are not the same).
O: Related to Fuel and Emissions System,- Connector with male terminals (double outline): View from terminal side
- Connector with female terminals (single outline): View from wire side
c'54*1
frl zlsl
fflErKwH---llOlBLr I
f6lGrrunEp -l
11-75

Page 346 of 2189

v1s8l7l6le t0r l!21
' S€cuitAr.h Sysi.m
cL5lwithod cruir. cort?oll
c510 ta/T)
;--F--trt2l
w
l-T - --l
l. - I
elz5{with crui* codrol)
r'ffitr
13 rl
lElwHT"cRN I
YELf,ED/BLK.!
- Connector with male terminals (double outline): View from terminal side
- Connector with female terminals (single outline): View from wire side
Different wires with the same cotor have been given a number suffix to distinguish them (for example, YEUBLKl
and YEUBLK'are not the same).
O; Related to Fuel and Emissions System
Dt!
t-
NOTE: o
a
a(cont'd)
11-77
t213t5
5
14i!aL(LTATU
1
Et0t1,/ ./ie /1Al,/ 20
2a
9t0l213111 /l61718
!t
t1t
23I7a9
101112t3/lr5l/18 t9
12
YEL
YEL3LK2

Page 348 of 2189

c130
I10
l112131,4t5ta11t8t9
ct3r
1lz3lt/X61789to
cr34 tEcM/PCM-C)cr35 lPCM-Dr:cr35lPcl|.D,€
ca32
lr 2 3.1
IiGTNiBN Ill
l5l-wxr,nol]ll:a BLX vHI I
NOTE; . Different wires with the same color have been given a number suffix to distinguish them (for example, YEUBLK1
and YEUBLK, are not the samel.
O: Related to Fuel and Emissions Svstem.- Connector with male terminals (double outline): View from terminal side
- Connector with female terminals (single outline): View from wire side
lrl2l
lll* -_-l
tn Bs I
c1a
lr 2l
f.fil
,bl onrrwlrl.lftlBLrwHri-Flirx,lvHJ l]-l
c,|52 tEcM/PCM-Al
\-a
't/3l-1.51
/tgto 'lt12l3
2at6IE e t|0111'12ItItIt[l
11-79

Page 349 of 2189

System Descriptions
System Connectors lFuel Pump]
('9!, - 00 models 6xcept Dl6Y5 ongino with M/T)
\(
I
c568
ffi
c565
E
c792
Different wires with the same color have been given a number suffix to distinguish them (for example, YEUBLKIand YEVBLK, are not the same).
O: Related to Fuel and Emissions System.- Connector with male terminals (double outline): View from terminal side- Connector with female terminals (single outline): View from wire side
c793
fr
NOTE: o
a
a
1 1-80

Page 1091 of 2189

Steering Wheel
l,/
Removal
SRS components are located in this area Review the
SRS component locations, precautions, and procedures
in the SRS section (24) before performing repairs or ser-
vice.
NOTE: Before removing the steering wheel. align the
front wheels straight ahead.
1. Remove the driver's airbag assembly from the
steering wheel (see section 24)
2. Disconnect the horn connector and cruise control
switches connector.
CRUISESWITCHES CONNECTOR
3. Remove the steering wheel nut
STEERING WHEEL NUT
Replace.
Remove the steering wheel by rocking it slightly from
side-to-side as you pull steadily with both hands.
ag N.m {5.0 kgt rn, 36lbfft)
1.,
17-35
lnstallation
CAUTION: Do not tap on the steering wheel or steering
column shaft when installing the stsering wheel.
NOTE: Before installing the steering wheel, align the
front wheels straight ahead.
1. Before installing the steering wheel, center the
cable reel, Do this by first rotating the cable reel
clockwise until it stops. Then rotate it counterclock-
wise approximately two turns The arrow mark on
the cable reel label should points straight up.
Install the steering wheel with the steering wheel
nut.
NOTE: Be sure the steering wheel shaft engages
the cable reel and canceling sleeve.
Attach the cruise control switches connector io the
steering wheel cliP,
Connect the horn connector.
Install the driver's airbag assembly, and confirm
proper system operation (see section 24).
Check the horn and cruise control switches for
proper operatrons.
CAELE REEL

Page 1093 of 2189

Steering Column
I
Removal/lnstallation
SRS components are located in this area. Review the
SRS component locations, precautions, and proceclures
in the SRS sectron (24) before pertorming repairs or ser-
vice.
NOTE: Before removing the steering column for SRS,
remove the driver's airbag assembly and cable reel lsee
section 24).
1. Remove the steering wheel (see page 17 35).
2. Remove the driver's dashboard lower cover and
driver's knee bolster (see section 20).
3. Remove the combination switch assembly from the
steering column sha{t by disconnecting the connec-
tors.
4. Disconnect the ignition switch connectors.
5. Remove the steering joint cover.
6. Bemove the steering joint bolls.
7. Disconnect the steering ioint by moving the joint
toward the column, and remove it from the column
shaft.
8. Remove the steering column by removing the
attaching nuts and bolt.
UPPER
RETAINING COLLABNOTE: Take care not to let the
retaining collar fall out ofposition during installation.
STEERING JOINT BOLTS22 N.m {2.2 kgf.m, 16lbtft}
9. Installation is the reverse of the removal procedure
NOTE:
. Make sure the steering joint is connected as follows:
a. Insert the upper end of the steering ioint onto the
steering shaft (line up the bolt hole with the flat on
the shait), and loosely install the upper joint bolt.
b. Slip the lower end of the steering joint onto the
pinion shaft (line up the bolt hole with the groove
around the shaft), and loosely install the lower
joint bolt.
Be sure that the lowei joint bolt is securely in the
groove in the pinion shaft.
c. Pull on the steering joint to make sure that the
steering joint js fully seated. Then tighten the ioint
bolts.
. 8e sure the wires are not caught or pinched by any
parts when installing the column
. Make sure the wire harness is routed and fastened
properly.
. Make sure the connectors are properly connected.
STEERING COLUMN
COMBINATION SWITCHASSEMBLY
FLANGE NUT13 N.m {1.3 kgl.m.9 lbf ft)
COLUMN COVER
FLANGE BOLTS22Nm12.2kgl'm,16 tbt.tr)
UPPER JOINT BOLTBolt musl line upon shaft.
Groove.
LOWER JOINT BOLT8oh must line up wrthgroove around on shaft.
CLIP
J
JOINT COVER
17-37

Page 1298 of 2189

Dashboard
Component RemovaUlnstallation
CAUTION: When prying with a flat-tip screwdriver,
wrap it with protoctivo tape, and apply protective tape
around tho r6lat6d parts, to prevent damag6.
NOTE: Take care not to scratch the dashboard and relatedpans.
Instrument Danel removal:
1.Lower the steering column.
Remove the screws, and detach the clips, then care-
fully remove the instrument panel.
3. Installation is the reverse of the removal procedure.
>: Clip locations, 2
.il |
Pit)_ _ ,/
>: Screw locations,2
^l
@sl
:)
PANEL
20-68
Driver's dashboard lower cover and knee bolster removal:
SRS components are located in this area. Review the SRS
component locations, precautions. and procedures in the
SRS section (24) before performing repairs or service.
'1. Remove the screws, and detach the clips, then
remove the driver's dashboard lower cover. lf
equipped with power mirrors and moonroof, discon-
nect the connectors.
>: Screw, boh loc.tionsA>.3B>,2
_-rri I /a_6x1.0mm*\Y @{[) s 8 N'm tt o rst'm,
_-_- J _ \J- 7 2_rbtftl -_
>: Clip locationsA>.2 B >, 1
tu
DRIVER'S DASHBOARDLOWER COVER
Remove the bolts, then remove the knee bolster.
Installation is the reverse of the removal procedure.

Page 1300 of 2189

Dashboard
Gomponent Removal/lnstallation
(cont'd)
Center panel removal:
1. Remove:
. Center dashboard lower cover (see page 20-69)
. Radio {see section 23)
2. Remove the rear window defogger switch and haz-
ard warning switch, then disconnect the connectors.
>: Screw locations, 5 >: Clip locationsA>,4 B>,3
fii*-)
CENTERPANEI.
rt-xR.
W
IHAZARDWARNINGswlTcH
r44 "
F.IZvl
IIREARwtNoowOEFOGGERswtrcH
MtxCONTNOLCABLE
3. Disconnect the air mix control cable, and remove the
screws, then pull out the center panel.
4. Disconnect the connectors from the heater control
u nit.
5. Installation is the reverse of the removal procedure.
NOTE:
. Make sure the connectors are connected properly.
. Adjust the air mix control cable (see section 21).
20-70
Removal
SRS components are located in this area. Review the
SRS component locations, precautions, and procedures
in the SRS section (24) before preforming repairs or ser-
vice.
NOTE:
. An assistant is helpful when removing and installing
the dashboard.
. Take care not to scratch the dashboard, body and
related parts.
1. Remove:
o Front and rear consoles (see page 20-67)
. Console panel (see page 2O 67),
. Driver's dashboard lower cover and knee bolster(see page 20-68)
. Glove box (see page 20-69)
. Center dashboard lower cover (see page 20-69i
2. Lower the steering column (see section 17).
@ To avoid accidental deplovment and
possible injury, always disconnect the driver's
airbag connector belore lowering the steering col-
umn lsee section 241.
NOTE: To prevent damage to the steering column,
wrap it with a shop towel.
3. Disconnect the dashboard wire harness connectors,
remove the nuts, then move the under-dash fuse/
relay box. Disconnect the antenna lead and moon-
roof relay connectors.
DASHBOARD cltPs
CONNECTORS(for some models)
MOONROOFRELAY
ANTENNALEAO
FRAME
SRS MAINHARNESS
9.8 N.m (1.0 kgf m,7.2lbt.ltl
DATACONNECTOR WIRE HARNESSDetach. CONNECTORS

Page:   < prev 1-10 11-20 21-30 31-40 41-50 50 next >