display HONDA CIVIC 2005 7.G Owners Manual

The odometer shows the total dis-
tance your vehicle has been driven.
It measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays by pressing the Select/
Reset button repeatedly.Each trip meter works independently,
so you can keep track of two
dif f erent distances.
To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0.’’ Both trip meters will reset if
the vehicle’s battery goes dead or is
disconnected.
This shows how much f uel you have.
It may show slightly more or less
than the actual amount. The needle
returns to the bottom after you turn
of f the ignition.
Gauges
Odometer T rip Meter
Fuel Gauge
U.S. L X, EX and Canadian L X-G and Si models
Inst rument s and Cont rols
61
ODOMETER/TRIP METER SELECT/RESET KNOB
The U.S. instrument
panel is shown TACHOMETER
SPEEDOMETER TEMPERATURE GAUGE
FUEL GAUGE
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
——y
y
(yy

The knob on the instrument panel
controls the brightness of the instru-
ment panel lights. Turn the knob to
adjust the brightness.There are six brightness levels.
When you turn the knob, the
odometer/trip meter display
changes to circles that show you the
current level. You will hear a tone
when you reach the maximum or
minimum brightness.Adjust the brightness to the desired
level with the headlight switch of f ,
and also with the headlight switch on.
To reduce glare at night, the
instrument panel illumination dims
when you turn the light switch to
or . Turning the Select/
Reset knob f ully to the right will
return the instrument panel to the
brightness adjusted with the
headlight switch of f and a tone willsound.OnLX,USEX,andCanadianSimodels
Instrument Panel Brightness
66
SELECT/RESET KNOB
DX models KNOB LX, U.S. EX, and Canadian
Si models
——y

y
(yy

µµ
µ
´
µ ´µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
Power Volume knob or the AM/FM
button (FM/AM button on Special
Edition models). Adjust the volume
by turning the Power Volume knob.
As you adjust a volume, you will hear
a beep whenever the adjustment
level reaches the maximum and
minimum of its range.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
or FM/AM button. On the FM band,
ST will be displayed if the station is
broadcasting in stereo. Stereo
reproduction on AM is not available. On the AM band, AM noise
reduction turns on automatically.
You can use any of f ive methods to
find radio station on the selected
band: the
preset buttons, and
Use the TUNE knob or
the SEEK bar to tune the radio to a
desired f requency.
Turn the knob to the right to tune a
higher f requency, and turn it to the
lef t to tune a lower f requency. The SEEK f unction
searches up and down f rom the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
SEEK bar, then release it.
The SCAN function
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor5seconds.Whenit
plays a station that you want to listen
to, press the SCAN button again.
Press the ‘‘ ’’ side of the SEEK bar
to tune a higher f requency, and
press the ‘‘ ’’ side to tune a lower
f requency. On Special Edition models, press the
‘‘ ’’ or ‘‘ ’’ side of the SEEK bar
until you hear a beep, then release it.
On Special Edition models
On Special Edition models
Except f or Special Edition modelsOn Special Edition models
CONT INUED
Playing the Radio
To Play the Radio To Select a StationTUNE,SEEK,SCAN, AUTO SELECT.
TUNE SEEK
SCAN
Features
93
——y
y
(yy

µµ
Each preset button can
store one f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset button and hold it
until you hear a beep.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. To select a dif f erent preset
f requency, you can also use the P.
CALL bar. Press the ‘‘ ’’ side of
the bar to select the frequency
stored in the next preset button, and
press the ‘‘ ’’ side to select the
f requency in the previous preset
button.
You will see a ‘‘0’’ displayed af ter
pressing a preset button if Auto
Select cannot f ind a strong station
f or every preset button.
If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons as previously described.
press the
A. SEL button. This restores the
presets you originally set.
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the Auto Select f eature
to find stations in the local area.
Press the A. SEL button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM, and twelve FM stations in
the preset buttons.
1. 2. 3. 4.On Special Edition models
To turn of f Auto Select,PresetAUTO SELECT
Playing the Radio
94
——y
y
(yy

µµ
µ µ
CONT INUED
Adjust the Balance, or side-
to-side strength of the sound.
Adjust the Fader, or the
f ront-to-back strength of the sound.
AdjusttheTrebleinthe
sound.
Adjust the Bass in the sound.
Press the SOUND (TUNE) knob or
SOUND button repeatedly to display
the Bass (BAS), Treble (TRE),
Balance (BAL), and Fader (FAD)
settings. Each mode is shown in the
display as it changes. The level gauge on the display also
shows you the range. As you adjust a
mode, you will hear a beep whenever
the adjustment level reaches the
center (C), maximum, and minimum
of its range.
Turn the SOUND (TUNE) knob to
adjust the setting to your liking.
Turn the Volume knob to adjust the
setting to your liking.
The displayed number shows you
the current setting. When the level
reaches the center, you will see a ‘‘C’’
in the display. The system will return
to the audio display about 5 seconds
af ter you stop adjusting a mode.
On Special Edition models
Except f or Special Edition models
On Special Edition modelsOn all models
Playing the Radio
Adjusting the Sound
BAL
FAD
TRE
BAS
Features
95
——y
y
(yy

On Special Edition modelsOn Special Edition models
You can display the sound with the
spectroscopic analysis. There are
five modes of display; Peak-Hold,
Normal, Aurora, Level and Off.
Each time you press and release
the DISP button, the mode
changes f rom P.HOLD to
NORMAL to AURORA to LEVEL,
then to OFF. You see the selected
mode in the display f or about 5
seconds as it changes.You can use the instrument panel
brightness control knob to adjust the
illumination of the audio system (see
page ). The audio system
illuminates when the parking lights
are on, even if the radio is turned of f .
You can also select the reduced
brightness in the display when the
parking lights are on. Press and hold
the DISP button for about 5 seconds
until you hear a beep to change the
brightness. Press and hold this
button again f or about 5 seconds
until you hear a beep to return to the
f ull brightness.
66
Playing the Radio
Spect roscopic A nalysis
Display bright ness
A udio System L ighting
96
——y
y
(yy

The radio can receive the complete
AM and FM bands.
Those bands cover these f requen-
cies:
AM band: 530 to 1,710 kilohertz
FM band: 87.7 to 107.9 megahertzHow well the radio receives stations
is dependent on many f actors, such
as the distance from the station’s
transmitter, nearby large objects,
and atmospheric conditions.
Driving very near the transmitter of
a station that is broadcasting on a
f requency close to the f requency of
the station you are listening to can
also af f ect your radio’s reception.
You may temporarily hear both
stations,orhearonlythestationyou
are close to.
A radio station’s signal gets weaker
as you get f arther away f rom its
transmitter. If you are listening to an
AM station, you will notice the sound
volume becoming weaker and the
stationdriftinginandout.If youare
listening to an FM station, you will
see the stereo indicator f lickering of f
and on as the signal weakens.
Eventually, the stereo indicator will
go of f and the sound will f ade
completely as you get out of range of
the station’s signal.
Radio stations on the AM band are
assigned f requencies at least ten
kilohertz apart (530, 540, 550).
Stations on the FM band are
assigned f requencies at least 0.2
megahertz apart (87.9, 88.1, 88.3).
Stations must use these exact
f requencies. It is f airly common f or
stations to round-of f the f requency in
their advertising, so your radio could
display a f requency of 100.9 even
though the announcer may identif y
the station as ‘‘FM101.’’
CONT INUED
Radio Frequencies Radio Reception
Radio Reception
Features
97
——y
y
(y
y

´
µ
Playing a Disc
Features
99
DISC BUTTON
DISC BUTTON
SEEK/SKIP BAR
CD SLOT
CD BUTTON
REPEAT INDICATOR REPEAT BUTTON
RANDOM BUTTON REPEAT BUTTON
AM/FM BUTTON
CD/TAPE BUTTON
POWER/VOLUME KNOB
POWER/
VOLUMEKNOB DISC SLOT
REPEAT INDICATOR RANDOM
INDICATOR
RANDOM BUTTON
EJECT
BUTTON
RANDOM
INDICATOR
SEEK/SKIP BAR DISPLAY
BUTTON
EJECT
BUTTON
FILE
INDICATOR/
NUMBER POWER/
VOLUMEKNOB
SEEK/SKIP
BAR
REPEAT BUTTON/
SCAN BUTTON
CD BUTTON
LOADED
DISC
NUMBER
MP3
INDICATOR
DX model
(Optional)
U.S.: LX, EX models
Canada: LX, Si models
AM/FM BUTTON LOAD BUTTON
DISC LOAD INDICATOR
TITLE BUTTON FOLDER INDICATOR/
NUMBER
RANDOM
BUTTON
FOLDER
BAR
DISK
NUMBER
——y
y
(y
y
U.S. Special Edition models

To load or play discs, the ignition
switch must be in the ACCESSORY
(I) or ON (II) position.
You operate the CD player/CD
changer with the same controls used
for the radio. To select the CD
player/CD changer, press the CD
button. You will see ‘‘CD’’ in the
display. The number of the track
playing is shown in the display. With
the in-dash CD changer, the disc and
track numbers are displayed. The
system will continuously play a disc
until you change modes.The in-dash CD changer can also
play CD-Rs and CD-RWs
compressed in MP3 standard. When
playing a disc in MP3, you will see
‘‘MP3’’ in the display. You can select
afolderortrackupto .
Video CDs and DVD discs will not
work in this unit.
The specif ications of the compatible
MP3 f ile are:
Sampling f requency: 32/44.1/48 kHz
Bit rate: 32/40/48/56/64/80/96/
112/128/160/192/224/256/320 kbps
Compatible with variable bit rate and
multi-session
Maximum layers
(including ROOT): 8 layersInsert a CD into the CD slot. The
drive will pull the CD in the rest of
the way to play it. When the system
reaches the end of the disc, it will
return to the beginning and play the
disc again.
You can also play 3-inch (8-cm) discs
without using an adapter ring.
To play the radio when a disc is
playing, press the AM/FM button.
Press the CD button again to switch
back to the CD player.
To play the tape when a CD is
playing, insert a tape in the player
(optional). If a tape is in the player,
press the TAPE button. Press the
CD button again, to switch back to
the CD player.
While playing a disc, you can see the
playing time in the display by
cancelling the clock display (see
page ). 255
116
On models with CD player
Optional on DX model
Playing a Disc
To Play a Disc
100
——y
y
(y
y
On U Special Edition modelsU.S.

CONT INUED
If you turn the system of f while a CD
is playing, either with the Power/
Volume knob or by turning of f the
ignition switch, the disc will stay in
the drive. When you turn the system
back on, the CD will begin playing
where it lef t of f .You cannot load and play 3-inch
(8-cm) discs in this unit.
When the disc load indicator turns
green and ‘‘LOAD’’ appears in the
display again, insert the next disc
in the slot. Do not try to insert a
disc until ‘‘LOAD’’ appears. You
could damage the audio unit.
Your vehicle’s in-dash CD changer
hold up to six discs.
Press the LOAD button until you
hear beep and see ‘‘LOAD’’ in the
display. To load only one disc,
press and release the LOAD
button. The green disc load
indicator will come on.
The disc number f or an empty
position begins blinking.
Insert the disc into the CD slot
when the green disc load indicator
comes on. Insert it only about
half way; the drive will pull it in the
rest of the way. You will see
‘‘BUSY’’ in the display while the
disc load indicator turns red and
blinks as the disc is loaded. Repeat this until all six positions
are loaded. If you are not loading
all six positions, the system begins
playing the last disc loaded.
You can also load a disc into an
empty position while a disc is playing
by pressing the appropriate preset
button. The system stops playing the
current disc and starts the loading
sequence. It plays the disc just
loaded.
1. 2. 3.
4. 5.
Playing a Disc
L oading Discs in t he In-dash CD
Changer
Features
101
——y
y
(y
y
On U Special Edition modelsU.S.