check engine light HONDA CIVIC COUPE 2006 8.G Owners Manual

If you turn the steering wheel to the
f ull lef t or right repeatedly while
stopping or driving at very low speed,
you may f eel slightly harder steering
due to overheating of the steering
gear box.
Continuously driving under those
conditions could damage the power
steering system.
This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance. The
maintenance main items and sub
items will be displayed in the
inf ormation display. See page f or
more inf ormation on the
maintenance minder.
This indicator goes of f when your
dealer resets it after completing the
required maintenance service.
This indicator normally comes on
when you turn the ignition switch to
the ON (II) position and goes of f
af ter the engine starts. If it comes on
at any other time, there is a problem
in the electric power steering system.
If this happens, stop the vehicle in a
saf e place, and turn of f the engine.
Reset the system by restarting the
engine. The indicator will not turn
of f immediately. If it does not go of f
after driving a short distance, or
comes back on again while driving,
take the vehicle to your dealer to
have it checked. With the indicator
on, the EPS may be of f , making the
vehicle harder to steer.
To protect the engine f rom damage,
never drive with the tachometer in
its red zone. This indicator shows you when the
engine speed is near the tachometer’s
red zone. When the engine speed
gets to near the red zone, the
indicator blinks. If you exceed the
maximum speed f or the gear you are
in, the indicator stays on, and you
may f eel the engine cut in and out
due to the engine speed limiter (see
page ).
209
197
Instrument Panel Indicators
Electric Power Steering
(EPS) Indicator
Maintenance Minder
IndicatorRev L imit Indicator
Si model only
Si model only
60
LEV LIMIT INDICATOR
——y
y
(+yy

This shows how much f uel you have.
It may show slightly more or less
than the actual amount.This shows the temperature of the
engine’s coolant. During normal
operation, the reading should rise to
about the middle of the gauge. In
severe driving conditions, such as
very hot weather or a long period of
uphill driving, the reading may rise
intotheupperhalfofthegauge.Ifit
reaches the red (Hot) mark, pull
safely to the side of the road. See
page f or instructions and
precautions on checking the engine
cooling system.If your f uel f ill cap is loose or
missing, a ‘‘CHECK FUEL CAP’’
message appears in the information
display af ter you start the engine.
The message goes f rom CHECK to
FUEL,thentoCAPrepeatedly.You
will also hear a beep.
Turn the engine of f , and conf irm the
f uel f ill cap is installed. If it is, loosen
the cap, then retighten it until it
clicks at least once. When you
restart the engine, the message
appears again. To clear the message,
press and hold the SEL/RESET
button until it goes away.
261
Fuel Gauge T emperature Gauge Check Fuel Cap Indicator
Gauges
66
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
——y
y
(+yy

Wait a f ew minutes af ter turning the
engine of f bef ore you check the oil.
Put your f ingers under the f ront
edge of the hood near the center.
Slide your hand to the lef t until
you f eel the hood latch handle.
Push this handle up to release it.
Lif t up the hood.
If the hood latch handle moves
stif f ly, or if you can open the hood
without lifting the handle, the
mechanism should be cleaned and
lubricated. Pull the support rod out of its clip
by holding the grip, and insert the
end into the designated hole in the
hood.
To close the hood, lif t it up slightly
to remove the support rod f rom
the hole. Put the support rod back
into its holding clip. Lower the
hood to about a f oot (30 cm) above
the fender, then let it drop. Make
sure it is securely latched.
Remove the dipstick (orange
handle).
Insert it all the way back in its tube. Wipe of f the dipstick with a clean
cloth or paper towel.
3. 1.
2.
3.
2.
CONT INUED
Service Station Procedures
Oil Check
Bef ore Driving
183
DIPSTICK
SUPPORT ROD
CLIP
LATCH
DX, Canadian DX-G, LX, EX
——y


y
(+y
y

Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).
Make sure the doors are securely
closed and locked. Check the steering wheel
adjustment (see page ). Check the adjustment of the
inside and outside mirrors (see
page ). Check that any items you may be
carrying are stored properly or
f astened down securely.
Check the seat adjustment (see
page ).
Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice.
Youshoulddothefollowingchecks
and adjustments bef ore you drive
your vehicle.
Check that the hood is f ully closed.
Check that the trunk is f ully
closed. When you start the engine, check
the gauges and indicators in the
instrument panel (see page ).
Visually check the tires. If a tire
looks low, use a gauge to check its
pressure (see page ).
1.
2.
14
3.
4. 5.
6.
7.
8.
9.
11.
10.
241 90
100 73 55
Preparing to Drive
Driving
193
——y
y
(+y
y

Check the brakes after driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious in your driving.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, and reduces their ef f ectiveness.
It also keeps your brake lights on all
the time, conf using drivers behind
you.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear. Your vehicle is equipped with f ront
disc brakes. The brakes on the rear
wheels may be disc or drum,
depending on the model. A power
assist helps reduce the ef f ort needed
on the brake pedal. The ABS helps
you retain steering control when
braking very hard. If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them.
Braking System Design Brake Wear Indicators
Braking System
Driving
203
——y

y
(+yy

This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
If you have the skills and tools to
perf orm more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer. This section also includes
instructions on how to read the
maintenance minder messages in the
inf ormation display, a maintenance
record, and instructions f or simple
maintenance tasks you may want to
take care of yourself .......................
Maintenance Saf ety .208
....................
Maintenance Minder .209
....................
Maintenance Record .216
..............................
Fluid Locations .218
........................
Adding Engine Oil .220
.......
Recommended Engine Oil .220
..............................
Synthetic Oil .221
................
Engine Oil Additives .221
.........
Changing the Oil and Filter .222
..............................
Engine Coolant .224
....................
Windshield Washers .227
....
Automatic Transmission Fluid .228
........
Manual Transmission Fluid .229
................
Brake and Clutch Fluid .230
....................
Power Steering Fluid .231
.............................................
Lights .232
................
Cleaning the Seat Belts .237
.....................................
Floor Mats .238
..................
Dust and Pollen Filter .239
.................................
Wiper Blades .239
...............................................
Tires .241
...................
Checking the Battery .248
.............................
Vehicle Storage .250
291
Maintenance
Maint enance
207
——y

y
(+y
y

µ
µ
µ
µ
µ
µ
Ì
U.S. Vehicles:
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the appropriate
page listed. Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
and license plate lights monthly.
See page .
Engine coolant level Check the
radiator reserve tank every time
you f ill the f uel tank. See page . Engine oil level Check every
time you fill the fuel tank. See
page .
Automatic transmission Check
the f luid level monthly. See page .
Brakes Check the f luid level
monthly. See page .
Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page .
According to state and federal
regulations, f ailure to perf orm
maintenance on the items marked
with will not void your emissions
warranties. However, all
maintenance services should be
perf ormed in accordance with the
intervals indicated by the
inf ormation display.
183
185
228 230
241 232
Maintenance, replacement, or
repair of emissions control
devices and systems may be done
by any automotive repair
establishment or individual using
parts that are ‘‘certif ied’’ to EPA
standards. Owner’s Maintenance Checks
Maintenance Minder
214
——y
y
(+y
y

When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound or series of clicks, or
nothing at all.
Check these things:Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, it must be
in Park or neutral.
Diagnosing why the engine won’t
start f alls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run.
Store the jack and tools in the tool
kit case. Place the tool kit case in
the center of the flat tire.
Store the wheel cover or center
cap in the trunk. Make sure it does
not get scratched or damaged.
Lower the trunk f loor, then close
the trunk lid.
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page .259
18.
19.
20.
CONT INUED
Nothing Happens or the Starter
Motor Operates Very Slowly
If the Engine Won’t Start
Jump Starting
Changing a Flat Tire, If the Engine Won’t Start
T aking Care of t he Unexpect ed
257
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.
——y

y
(+yy

Do you have f uel? Check the f uel
gauge; the low f uel indicator may
not be working.
There may be an electrical
problem, such as no power to the
f uel pump. Check all the f uses
(see page ).
If youfindnothingwrong,youwill
need a qualif ied technician to f ind
the problem. See on page .
Are you using a properly coded
key? An improperly coded key will
cause the immobilizer system
indicator in the instrument panel
to blink rapidly (see page ).
Are you using the proper starting
procedure? Ref er to
on page .
In this case, the starter motor’s
speed sounds normal, or even f aster
than normal, when you turn the
ignition switch to the START (III)
position, but the engine does not run.
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the f uses. If the f uses
areOK,thereisprobably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualif ied technician to
determine the problem (see
on page ).
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is dis-
charged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page ). You can
then try jump starting the vehicle
f rom a booster battery (see page ). 272
248
259 75
194 266
272Emergency
Towing
T he Starter Operates Normally
Starting the
Engine
Emergency T owing
If theEngineWon’tStart
258
——y

y
(+y
y

CONT INUED
...
Accessories and Modif ications .186
ACCESSORY (Ignition Key
.......................................
Position) .76
............
Accessory Power Sockets .104
................
Adding Engine Coolant .224
....................
Additives, Engine Oil .221
.......
Adjusting the Steering Wheel .73
.........
Advice f or Pregnant Women .16
...............................
Airbag (SRS) .9,21
..............
Air Conditioning System .110
.........................................
Usage .113
.......................
Air Pressure, Tires .242
.......................
Alcohol in Gasoline .180
......................................
Antif reeze .224
Anti-lock Brakes (ABS)
...............................
Indicator .59, 204
...................................
Operation .204
..............
Anti-thef t, Audio System . 172
Anti-thef t Steering Column ..............................................
Lock .76
................................
Audio System .115
.....
Auto Door Locking/Unlocking . 78
...
Automatic Seat Belt Tensioners . 19
.............
Automatic Speed Control . 175..............
Automatic Transmission . 198
..........................
Capacity, Fluid .278
...............
Checking Fluid Level . 228
.......................................
Shif ting .198
Shif t Lever Position ...............................
Indicators .198
................
Shif t Lever Positions . 198
....................
Shif t Lock Release . 201
Battery Charging System ...........................
Indicator .57, 263
............................
Jump Starting .259
..............................
Maintenance .248
............................
Specif ications .279
..............................
Bef ore Driving .179
....................................
Belts,Seat .8,18
.........................
Beverage Holders .103
..................................
Booster Seats .47
Brakes ...........
Anti-lock System (ABS) . 204
.............
Break-in, New Linings . 180
....................
Bulb Replacement .236
...........................................
Fluid .230 .......................................
Parking .101
..........................
System Design .203
.................
System Indicator . 58,265
........................
Wear Indicators .203
.............................
Braking System .203
.................
Break-in, New Vehicle . 180
..
Brightness Control, Instruments . 71
........................
Brights, Headlights .70
Bulb Replacement ..........................
Back-up Lights .236
..............................
Brake Lights .236
................
Front Parking Lights . 235
........
Front Side Marker Lights . 235
.................................
Headlights .232
.........
High-mount Brake Light . 237
............................
Specif ications .279
....................
Turn Signal Lights . 235
..............................
Bulbs, Halogen .232
............................
Capacities Chart .278
.............
Carbon Monoxide Hazard . 50
.............................
Carrying Cargo .188
Index
A
B
C
INDEX
I
——y
y
(+yy