weight HONDA CR-V 2005 RD4-RD7 / 2.G Owner's Manual

µ
µ
µ
To achieve a proper tongue load,
start by loading 60 percent of the
load toward the front of the trailer
and 40 percent toward the rear, then
re-adjust the load as needed.
Discuss your needs with your trailer
sales or rental agency, and f ollow the
guidelines in this section. Also make
sure that all equipment is properly
installed and maintained, and that it
meets f ederal, state, province, and
local regulations.
Any hitch used on your vehicle must
be properly bolted to the underbody.
Always use saf ety chains when you
tow a trailer. Make sure the chains
are secured to the trailer and hitch,
and that they cross under the tongue
and can catch the trailer if it
becomes unhitched. Leave enough
slack to allow the trailer to turn
corners easily, but do not let the
chains drag on the ground.
The maximum
allowable weight of the vehicle, all
occupants, all accessories, all cargo,
and the tongue load is 4,450 lbs
(2,020 kg).
The maximum
allowable weight of the vehicle, all
occupants, all accessories, all cargo,
and the tongue load must not exceed
2,200 lbs (1,000 kg) on the f ront axle,
and 2,290 lbs (1,040 kg) on the rear
axle.
The maximum
allowable weight of the f ully loaded
vehicle and trailer is 5,950 lbs (2,700
kg)
Towing can require a variety of
equipment, depending on the size of
your trailer, how it will be used, how
much load you are towing, and
where you tow.
Using a suitable scale or a special
tongue load gauge, check the tongue
load the f irst time you set up a
towing combination (a f ully-loaded
vehicle and trailer), then recheck the
tongue load whenever the conditions
change.
Thebestwaytoconfirmthatvehicle
and trailer weights are within limits
is to have them checked at a public
scale.
CONT INUED
Towing a Trailer
Hitches
Saf et y Chains
Gross Vehicle Weight Rating
(GVWR)
Gross Axle Weight Ratings
(GA WR)
Gross Combined Weight Rating
(GCWR)
T owing Equipment and
A ccessories
Checking L oads
Driving
173

Honda requires that any trailer with
a total weight of 1,000 lbs (455 kg) or
more be equipped with its own
electric or surge-type brakes.
If you choose electric brakes, be
sure they are electrically actuated.
Do not attempt to tap into your
vehicle’s hydraulic system. No
matter how successf ul it may seem,
any attempt to attach trailer brakes
to your vehicle’s hydraulic system
will lower braking ef f ectiveness and
create a potential hazard.
Seeyourtrailerdealerformore
inf ormation on installing electric
brakes.
Trailer lights and equipment must
comply with f ederal, state, province,
and local regulations. Check with
your local trailer sales or rental
agencies f or the requirements in
your area where you plan to tow, and
use only equipment designed f or
your vehicle.
Your vehicle has a trailer lighting
connector located behind the lef t
side panel in the cargo area. Ref er to
the drawing above f or the wiring
color code and purpose of each pin.
If you use a non-Honda trailer
lighting harness and converter, you
can get the connector and pins that
mate with the connector in your
vehicle f rom your dealer.
Since lighting and wiring vary by
trailer type and brand, you should
have a qualified technician install a
suitable connector between the
vehicle and the trailer. Improper
equipment or installation can cause
damage to your vehicle’s electrical
system and af f ect your vehicle
warranty.
Towing a Trailer
T railer L ights Trailer Brakes
174
BACK-UP LIGHT(GREEN/BLACK)
LEFT TURN SIGNAL(GREEN/RED)
GROUND (BLACK)
TAILLIGHT (RED/YELLOW)
RIGHT TURN SIGNAL(GREEN/YELLOW)
BRAKE LIGHT(WHITE/BLACK)

The lights and brakes on your
vehicle and the trailer are working
properly.
When preparing to tow, and bef ore
driving away, be sure to check the
f ollowing:
The vehicle has been properly
serviced, and the tires, brakes,
suspension, cooling system, and
lights are in good operating
condition.
(If you tow f requently, f ollow the
severe conditions maintenance
schedule.)
The trailer has been properly
serviced and is in good condition.
All weights and loads are within
limits.
Thehitch,safetychains,andany
other attachments are secure.
All items in or on the trailer are
properly secured and cannot shif t
while you drive.
The added weight, length, and
height of a trailer will af f ect your
vehicle’s handling and perf ormance,
so driving with a trailer requires
some special driving skills and
techniques.
Many states and Canadian provinces
require special outside mirrors when
towing a trailer. Even if they don’t,
you should install special mirrors if
you cannot clearly see behind you, or
if the trailer creates a blind spot.
Askyourtrailersalesorrental
agency if any other items are
recommended or required f or your
towing situation.
Your vehicle tires and spare are
properly inf lated, and the trailer
tires and spare are inf lated as
recommended by the trailer
maker.
Foryoursafetyandthesafetyof
others, take time to practice driving
maneuvers bef ore heading f or the
open road, and f ollow the guidelines
in this section.
CONT INUED
Towing a Trailer
Pre-T ow Checklist
Driving Saf ely With a T railer
A ddit ional T owing Equipment
Driving
175

Honda Motor Oil is the pref erred
5W-20 lubricant f or your vehicle. It is
highly recommended that you use
Honda Motor Oil in your vehicle f or
optimum engine protection. Make
sure the API Certif ication Seal says
‘‘For Gasoline Engines.’’
The oil viscosity or weight is
provided on the container’s label.
5W-20 oil is f ormulated f or year-
round protection of your vehicle to
improve cold weather starting and
f uel economy.
Unscrew and remove the engine oil
fill cap on top of the valve cover.
Pour in the oil slowly and caref ully so
you do not spill any. Clean up any
spills immediately. Spilled oil could
damage components in the engine
compartment.
Reinstall the engine oil f ill cap, and
tighten it securely. Wait a f ew
minutes, and recheck the oil level on
the engine oil dipstick. Do not f ill
above the upper mark; you could
damage the engine.
Oil is a major contributor to your
engine’s perf ormance and longevity.
Always use a premium-grade 5W-20
detergent oil displaying the API
Certif ication Seal. This seal indicates
the oil is energy conserving, and that
it meets the American Petroleum
Institute’s latest requirements.
A dding Engine Oil
A dding Engine Oil
Recommended Engine Oil
Maint enance
193
ENGINE OIL FILL CAP
API CERTIFICATION SEAL
Ambient Temperature

Your vehicle does not require any oil
additives. Additives may adversely
af f ect the engine or transmission
perf ormance and durability.
Always change the oil and f ilter
according to the recommendations in
the maintenance schedule. The oil
and f ilter collect contaminants that
can damage your engine if they are
not removed regularly.
Changing the oil and f ilter requires
special tools and access f rom
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lif t f or this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
mechanic.
Run the engine until it reaches
normal operating temperature,
then shut it off.
Open the hood, and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
You may use a synthetic motor oil if
it meets the same requirements
given f or a conventional motor oil, it
displays the API Certif ication Seal
and it is the proper weight. You must
f ollow the oil and f ilter change
intervals given in the maintenance
schedule.
1.
2.
A dding Engine Oil, Changing the Oil and Filter
Synthetic Oil
Engine Oil A dditives
Changing the Oil and Filter
194
WASHER
OIL DRAIN BOLT

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
The driver’s and the rear f loor mats
that came with your vehicle hook
over the f loor mat anchors. This
keeps the f loor mat f rom sliding
f orward and possibly interf ering with
the pedals or making the front
passenger’s weight sensors
inef f ective.
Cleaning the Seat Belts Floor Mats
Cleaning the Seat Belts, Floor Mats
208
LOOP

This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the heating and
cooling system.
Have your dealer replace this filter
every 30,000 miles (48,000 km)
under normal conditions. It should
be replaced every 15,000 miles
(24,000 km) if you drive primarily in
urban areas that have high
concentrations of soot in the air, or if
the f low f rom the heating and
cooling system becomes less than
usual.
Make sure the rear f loor mats are
properly hooked to the f loor mat
anchors. Your vehicle is equipped
with f ront passenger’s seat weight
sensors. If the rear passenger’s f loor
mat is on the seat rail of the f ront
passenger’s seat, the sensors will
detect the decreased weight on the
seat, and they may not work properly.
If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.
If you use a non-Honda f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.
Dust and Pollen Filter A udio A ntenna
Floor Mats, Audio Antenna, Dust and Pollen Filter
Maint enance
209
Your vehicle is equipped with an
antenna on the f ront right f ender.
Bef ore using a ‘‘drive-through’’ car
wash, make sure you remove the
antenna by unscrewing it by hand. This
prevents the antenna f rom being
damaged by the car wash brushes.

In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
Have your dealer check the tires if
you f eel a consistent vibration while
driving. A tire should always be
rebalanced if it is removed f rom the
wheel. When you have new tires
installed, make sure they are
balanced. This increases riding
comf ort and tire lif e. For best results,
have the installer perform a dynamic
balance.
To help increase tire lif e and
distribute wear more evenly, rotate
the tires every 10,000 miles (16,000
km). Move the tires to the positions
showninthecharteachtimethey
are rotated. If you purchase
directional tires, rotate only f ront-to-
back.
Replace your tires with radial tires of
the same size, load range, speed
rating, and maximum cold tire
pressure rating (as shown on the
tire’s sidewall).
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
ABS and vehicle stability assist
system (VSA) to work inconsistently.
For vehicles equipped with aluminum
wheels:
T ire Maintenance T ire Rotation Replacing T ires and Wheels
Tires
214
Front Front
(For Non-directional Tires and Wheels) (For Directional Tires and Wheels)
Improper wheel weights can damage
your vehicle’s wheels. Use only Honda
wheel weights f or balancing.

Î
Î
Î
Î
Î Î
Î
Specif ications
246
Capacities
Engine
Weights
Dimensions Capacities 181.0 in (4,597 mm)1.43 US gal (5.4)1.88 US gal (7.1)
1.45 US gal (5.5) 1.90 US gal (7.2)
3.3 US qt (3.1) 3.1 US qt (2.9)
7.6 US qt (7.2) 6.9 US qt (6.5)2.0 US qt (1.9)2.4 US qt (2.3)
1.1 US qt (1.0) 1.3 US qt (1.2)
4.8 US qt (4.5) 2.6 US qt (2.5)
0.16 US gal (0.6)
Excluding the oil remaining in the engine Including the coolant in the reserve tank and that remaining in theengineReserve tank capacity:
Fuel tank
Engine oil
5.6 US qt (5.3) 4.2 US qt (4.0)4.4 US qt (4.2)
15.3 US gal (58)
Type
BorexStroke DisplacementCompression ratioSpark plugs
Gross vehicle weight rating
Length
Width HeightWheelbaseTrack
See the certification label attached to the driver’s doorjamb.
SKJ20DR-M11 IZFR6K-119.6 : 1144 cu-in (2,354 cm)3.43 x 3.90 in (87.0 x 99.0 mm)
60.6 in (1,538 mm) 60.4 in (1,533 mm)103.1 in (2,620 mm)66.2 in (1,682 mm)70.2 in (1,782 mm)181.8 in (4,617 mm)Engine coolant
Automatic transmissionfluid
Manual transmissionfluidReardifferentialfluid (4WD)Windshieldwasherreservoir
Water cooled 4-stroke DOHC i-VTEC 4-cylinder gasoline engine
Approx.
Front Rear
Change
Without filter Total
1: 2:
Change Total
Change TotalChange4WD2WDTotal4WD2WDChangeTotal
Change Total
U.S. Vehicles CanadaVehicles (NGK) (DENSO)
1 : U.S. SE model and Canada EX-L model
Automatic Transmission
Manual Transmission
1
2
2
1
Including filter

...............
Gas Mileage, Improving . 147
..........................................
Gasohol .142
.........................................
Gasoline .142
.....................
Low Fuel Indicator .59
...........................................
Gauge .62
................
Octane Requirement . 142
........................
Tank, Ref ueling .143
................
Gas Station Procedures . 143
Gauges ...
Engine Coolant Temperature . 62
...............................................
Fuel .62
Gearshif t Lever Positions ..........
Automatic Transmission . 161
..............
Manual Transmission . 159
........................................
Glove Box .93
Gross Vehicle Weight Rating .............................
(GVWR) .173, 246 ...
Identif ication Number, Vehicle . 244
Ignition ..............................................
Keys .70
...........................................
Switch .72
............
Timing Control System . 252
........................
Immobilizer System .71
.........
Important Safety Precautions . 6
Fluids
..........
Automatic Transmission . 199
..........................................
Brake .201
.........................................
Clutch .202
..............
Manual Transmission . 200
..........................
Power Steering .202
..................
Windshield Washer . 198
.....................
Folding Rear Seat .82, 83
..........................
Four-way Flashers .67
..............................
Front Airbags .9 ,23
Front Seat ......................................
Adjusting .78
.........................................
Heaters .86
.....................................
Airbags .9, 23
.................................................
Fuel .142
..........
Check Fuel Cap Indicator . 63
......................
Fill Door and Cap .143
.....................
Low Fuel Indicator .59
...........................................
Gauge .62
................
Octane Requirement . 142
...............................
Oxygenated .142
........................
Tank, Ref ueling .143
...............................
Fuel Economy .147
.....................
Fuses, Checking the .237 .............
Halogen Headlight Bulbs . 203
.....................................
Hatch Glass .74
..............
Hazard Warning Flashers . 67Headlights
........................................
Aiming .203
............
Daytime Running Lights . 67
..................
High Beam Indicator . 59
...........................
Reminder Tone .66
........
Replacing Halogen Bulbs . 203
...................................
Turning on .66
..............................
Head Restraints .80
...............................
Heated Mirrors .89
.....................................
Heater, Seat .86
.......................
Heating and Cooling .98
............................
High Beam Lever .67
.......................
Hood, Opening the .144
..............................................
Horn .4,64
...........................
Hydraulic Clutch .202
Index
G
H I
IV