dead battery HONDA ELEMENT 2003 1.G Owners Manual

If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use. You should do
the f ollowing.Start the engine. Push down on
the driver’s window switch until
the window is f ully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by a Honda dealer.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If the driver’s window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
To open a rear window, pull the lever
towards you, then push it out until it
locks. To close the rear window pull
the lever towards you, then push it
back. Make sure the window is f ully
closed and locked.
1.
2.
Auto Reverse
Rear Windows
Power Windows, Rear Windows
Inst rument s and Cont rols105

µ
µ µ
µ The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM. Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
To store a f requency:
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the preset buttons.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Releasetheknobwhenthedisplay
reaches the desired f requency.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
theSEEKbaroneitherthe or side, then release it.
Depending on which side you press,
the system scans upward or down-
ward f rom the current f requency. It
stops when it finds a station with a
strong signal. The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. When the system is
intheSCANmode,SCNshowsin
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for about five
seconds. If you do nothing, the
system will then scan f or the next
strong station and play that for five
seconds. When it plays a station that
you want to continue listening to,
press the SCAN button again.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band. 1.
2.
3.
4.
Audio System
Comf ort and Convenience Feat ures
TUNE
SEEK
SCAN
Preset
127

You can use the R (Preset 6) button
to quickly set the time to the nearest
hour. Press the R button while
pressing the CLOCK button. If the
displayed time is bef ore the half
hour, pressing R sets the clock back
to the previous hour. If the displayed
time is af ter the half hour, pressing
R sets the clock f orward to the
beginning of the next hour.For example:
1:06 would RESET to 1:00.
1:52 would RESET to 2:00.
If your vehicle’s battery is
disconnected or goes dead, the time
setting will be lost. To set the time
again, f ollow the setting procedure.
To set the hour, press the H (Preset
4) button while pressing the CLOCK
(SCAN/RPT) button. Press and hold
the H button until the hour advances
to the desired time.
To set the minute, press the M
(Preset 5) button while pressing the
CLOCK (SCAN/RPT) button. Press
andholdtheMbuttonuntilthe
minute numbers advance to the
desired time.
Audio System
Comf ort and Convenience Feat ures131

µ
µ
µ µ
CONT INUED
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Stop turning the knob when the dis-
play reaches the desired f requency.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
either SEEK button ( or ),
then release it. Depending on which
SEEK button you press, the system
scans upward or downward f rom the
current f requency. It stops when it
finds a station with a strong signal.
The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. When the system is
intheSCANmode,SCNshowsin
the display. The system will scan up
the band for a station with a strong signal. When it f inds one, it will stop
and play that station for about five
seconds. If you do nothing, the
system will then scan f or the next
strong station and play that for five
seconds. When it plays a station that
you want to continue listening to,
press the SCAN button again.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
To store a f requency:
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
1. 4. 3.
2.
Audio System
Comf ort and Convenience Feat ures
TUNE
SEEK
SCAN
Preset
139

Youshouldhavereceivedacardthat
lists your audio system’s code
number and serial number. It is best
tostorethiscardinasafeplaceat
home. In addition, you should write
the audio system’s serial number in
this Owner’s Manual. If you should
happen to lose the card, you must
obtain the code number f rom your
Honda dealer. To do this, you will
need the system’s serial number.If your vehicle’s battery is discon-
nected or goes dead, or the radio
f use is removed, the audio system
will disable itself . If this happens,
you will see ‘‘CODE’’ in the
frequencydisplaythenexttimeyou
turn on the system. Use the preset
buttons to enter the five-digit code.
For example if your code is ‘‘1, 2, 3, 4,
5,’’ press the 1, 2, 3, 4, and 5 preset
buttons. If the code is entered
correctly, the radio will start playing.
If you make a mistake entering the
code, do not start over or try to
correct your mistake. Complete the
f ive-digit sequence, then enter the
correct code. You have ten tries to
enter the correct code. If you are
unsuccessful in ten attempts, you
must then leave the system on for
one hour bef ore trying again.
You will have to store your favorite
stations in the preset buttons after
the system begins working. Your
original settings were lost when
power was disconnected.
Your vehicle’s audio system will
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, the user
must enter a specif ic f ive-digit code
in the preset buttons. Because there
are hundreds of number
combinations possible f rom f ive
digits, making the system work
without knowing the exact code is
nearly impossible.
On EX models
Thef t Protection
Audio System
Comf ort and Convenience Feat ures152

µ
µ Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to Park posi-
tion if you need to leave the vehicle
f or any reason. Press on the brake pe-
dal when you are moving the shif t
lever from Neutral to another gear.
If you have done all of the above and
still cannot move the lever out of
Park, see Shif t Lock Release on page
. Your vehicle has a reverse lockout so
you cannot accidentally shif t to
Reverse when the vehicle speed
exceeds 5 mph (8 km/h).
You must also press the release
button to shift into Park. To avoid
transmission damage, come to a
complete stop bef ore shif ting into
Park. The shif t lever must be in Park
bef ore you can remove the key f rom
the ignition switch. To shif t to Reverse
f rom Park, see the explanation under
Park. To shif t to Reverse f rom
Neutral, come to a complete stop and
then shift. Press the release button
bef ore shif ting into Reverse f rom
Neutral. If you cannot shif t to Reverse when
the vehicle is stopped, press the
brake pedal, and slowly shift to
Neutral. Then press the release
button, and shift to Reverse.
If there is a problem in the reverse
lockout system, or your vehicle’s
battery is disconnected or goes dead,
you cannot shif t to Reverse. (Ref er
to Shif t Lock Release on page ).
183
183
Neutral (N)
Reverse (R)
Automatic Transmission
Driving180

µIf you need to connect the battery to
a charger, disconnect both cables to
prevent damage to the vehicle’s
electrical system.
If the terminals are severely cor-
roded, clean them with baking soda
and water. Then use a wrench to
loosen and remove the cables f rom
the terminals. Always disconnect the
negative ( ) cable f irst and recon-
nect it last. Clean the battery termi-
nals with a terminal cleaning tool or
wire brush. Reconnect and tighten
the cables, then coat the terminals
with grease. If your vehicle’s battery is
disconnected or goes dead, the audio
system will disable itself . The next
timeyouturnontheradioyouwill
see ‘‘CODE’’ in the f requency display.
Use the preset buttons to enter the
f ive-digit code (see page ). You
will then have to set the clock and
enter your station presets.
152
On EX models
Battery
Maint enance241
The battery gives off explosive
hydrogen gas during normal
operation.
A spark or flame can cause the
battery to explode with enough
force to kill or seriously hurt you.
Wear protective clothing and a
face shield, or have a skilled
mechanic do the battery
maintenance. Charging the battery with the cables
connected can seriously damage your
vehicle’s electronic controls. Detach
the battery cables bef ore connecting
the battery to a charger.

To check if they are set, turn the
ignition ON (II), but do not start the
engine. The Malf unction Indicator
Lamp will come on f or 20 seconds. If
it then goes of f , the readiness codes
are set. If it blinks 5 times, the
readiness codes are not set.
Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
If your vehicle’s battery has been
disconnected or gone dead, these
codes are erased. It takes several
days of driving under various
conditions to set the codes again. If possible, do not take your vehicle
f or a state emissions test until the
readiness codes are set. Ref er to
State Emissions Testing f or more
inf ormation. (See page .)
316
Readiness Codes
Malf unction Indicator L amp
T aking Care of t he Unexpect ed293

If you take your vehicle f or a state
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions.If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle re-tested within the
next two or three days, you can
condition the vehicle for re-testing
by doing the f ollowing.
Make sure the gas tank is nearly,
but not completely, f ull (around
3/4).
Make sure the vehicle has been
parked with the engine of f f or 8
hours or more.
Make sure the ambient
temperature is between 20° and
95°F. Without touching the accelerator
pedal, start the engine and let it
idle f or 20 seconds.
Keep the vehicle in Park
(automatic transmission) or
Neutral (manual transmission).
Increase the engine speed to 2,000
rpm and hold it there until the
temperature gauge rises to at least
1/4of thescale(approximately3
minutes).
T esting of Readiness Codes
St at e Emissions T est ing
T echnical Inf ormation316

ÎCONT INUED
.................................
Saf ety Features .7
.........................................
Airbags .10
..................................
Door Locks .11
..........................
Head Restraints .11
.......................................
Seat Belts .8
.....................
Seats & Seat-Backs .11
.............
Saf ety Labels, Location of . 61
...............................
Saf ety Messages . ii
.....................................
Seat Belts .8, 50
...............
Additional Information . 50
.....
Advice f or Pregnant Women . 21
Automatic Seat Belt ...............................
Tensioners .52
.....................................
Cleaning .271
................
Lap/Shoulder Belt . 17,50
................................
Maintenance .53
Reminder Light and ................................
Beeper .50, 67
................................
Replacement .53
...................
System Components . 50
...............
Use During Pregnancy . 21
...
Wearing a Lap/Shoulder Belt . 17
........................
Seats, Adjusting the .92
...............................
Serial Number .304
...........................
Service Intervals .212
...........................
Service Manual .323 .........
Service Station Procedures . 159
..................
Setting the Clock . 130,142
.....
Shif t Lever Position Indicator . 178
........................
Shif t Lock Release .183
..............................
Side Airbags .10, 56
....................
Cutof f Indicator .58, 67
Side Marker Lights, Bulb ..............................
Replacement .260
...............................
Signaling Turns .77
..........................................
Skylight .107
..............
Removing and Storing . 108
.....................................
Snow Tires .254
...................
Solvent-type Cleaners . 268
........................
Sound System .126, 137
......................................
Spare Tire .276
................
Spark Plugs, Replacing . 238
....................
Specif ications Charts . 306
................................
Speed Control .153
...................................
Speedometer .72
.......................................
Spotlights .114
..........
SRS, Additional Inf ormation . 54
...
Additional Safety Precautions . 59
.............................
Airbag Service .59
How the Side Airbag Cutof f ...........
Indicator Light Works . 58
..
How the SRS Indicator Works . 57How Your Front Airbags
.........................................
Work .54
...
How Your Side Airbags Work . 56
........................
SRS Components .54
.............................
SRS Indicator .57 ,67
....
START (Ignition Key Position) . 86
..............
State Emissions Testing . 316
.......................
Starting the Engine .174
In Cold Weather at High ..................................
Altitude .175
................
With a Dead Battery . 285
........
Steam Coming f rom Engine . 288
Steering Wheel ..................................
Adjustment .82
.............
Anti-theft Column Lock . 85
...........
Stereo Sound System . 126,137
....................
Storing Your Vehicle .266
Supplemental Restraint ................................
System .10, 54
......................................
Servicing .59
.........................
SRS Indicator .57 ,67
...................
System Components . 54
..................................
Synthetic Oil .222
Index
VII