HONDA PILOT 2007 1.G Manual PDF
Page 71 of 319
This indicator monitors the
temperature of the automatic
transmission f luid. It should come on
f or a f ew seconds when you turn the
ignition switch to the ON (II)
position. If it comes on while driving,
it means the transmission f luid
temperature is too high. Pull to the
side of the road when it is saf e, shif t
to Park, and let the engine idle until
the indicator goes out.If the indicator blinks while driving,
the VTM-4 fluid temperature is too
high. Pull to the side of the road
when it is saf e, shif t to Park, and let
the engine idle until the indicator
goes out. This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. If it comes on at any other
time, there is a problem in the 4WD
system. Take the vehicle to your
dealer to have it checked.While the engine is operating in its
most economical range, this
indicator may come on and stay on.
4WD models only
4WD models only2WD models only
A/T Temperature
IndicatorVT M-4 Indicator Fuel Economy Indicator
Instrument Panel Indicators
68
Continuing to drive with the A/T
temperature indicator on may cause
serious damage to the transmission.
Continuing to drive with the VTM-4
indicator blinking may cause serious
damage to the system. 
Page 72 of 319
This indicator  reminds you that  it is
time  to take  your  vehicle  in for
scheduled  maintenance.  The
maintenance  main  items  and sub
items  will be displayed  in the
information  display. See  page  for
more  information  on the
maintenance  minder.
This  indicator  goes off  when  your
dealer  resets it after  completing  the
required  maintenance  service.
This 
indicator  reminds you that  the
exterior  lights are on. It comes  on
when  the light  switch  is in  either  the
or  position.  If you  turn  the
ignition  switch to the  ACCESSORY
(I)  or LOCK  (0) position  without
turning  off  the  light  switch,  this
indicator  will stay  on. A reminder
chime  will also  sound  when you open
the  driver’s  door. This 
indicator  comes  on when  you
tu rn  on  the  fog  lights.  For more
info rmation,  see page  .
229
75
On EX and EX-L models
Instrument Panel Indicators
L ights On Indicator
Fog L ight Indicator Maintenance Minder
Indicator
Inst rument s and Cont rols
69 
Page 73 of 319
Each trip meter works independently,
so you can keep track of two
dif f erent distances.The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial
regulations to disconnect, reset, or
alter the odometer with the intent to
change the number of miles or
kilometers indicated.
This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. This shows how much f uel you have.
It may show slightly more or less
than the actual amount. The needle
returns to the bottom after you turn
of f the ignition.
To reset a trip meter, display it, and
then press and hold the Select/Reset
knob until the number resets to ‘‘0.0’’.
There are two trip meters: Trip A
and Trip B. Switch between these
displays and the outside temperature
display (except LX models) by
pressing the Select/Reset knob
repeatedly. Trip Meter Odometer
Fuel Gauge
Gauges
70
TACHOMETER
SPEEDOMETER FUEL GAUGE TEMPERATURE
GAUGE
TRIP METER
INFORMATION DISPLAY TRIP METER
SELECT/RESET
KNOB
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter. 
Page 74 of 319
¶¶µµ
µµµ
µµµ
This 
shows  the temperature  of the
engine’s  coolant. During normal
operation,  the pointer  should rise
from  the bottom  white mark to about
the  middle  white mark.  In severe
driving  conditions,  such as very  hot
weather  or a long  period  of uphill
driving,  the pointer  may rise to the
upper  white mark.  If it reaches  the
red  (Hot)  mark,  pull safely  to the
side of the road. Turn to page f or
instructions and precautions on
checking the engine’s cooling
system. NOTE: The temperature must be
stabilized bef ore doing this
procedure.
This indicator displays the outside
temperature in Fahrenheit (U.S.
models) or Centigrade (Canadian
models). To see the outside
temperature, press and release the
Select/Reset knob until the
temperature is displayed. If the outside temperature is
incorrectly displayed, you can adjust
it up to 5°F in U.S. models ( 3°C
in Canadian models) warmer or
cooler.
Select the outside temperature
indicator, then press the Select/
Reset knob f or 10 seconds. The
f ollowing sequence will appear f or 1
secondeach:0,1,2,3,4,5, 5, 4,
3, 2, 1, 0 (U.S.) or 0, 1, 2, 3,
3, 2, 1, 0 (Canada).
In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace. When the temperature reaches the
desired value, release the Select/
Reset knob. You should see the new
outside temperature displayed.
The temperature sensor is in the
f ront bumper. Theref ore, the
temperature reading can be af f ected
by heat ref lection f rom the road
surf ace, engine heat, and the
exhaust f rom surrounding traf f ic.
This can cause an incorrect
temperature reading when your
speed is under 19 mph (30 km/h).
The sensor delays the display update
until it reaches the correct outside
temperature. This may take several
minutes.
242
On EX and EX-L models
Temperature Gauge
Outside Temperature Indicator
Gauges
Inst rument s and Cont rols
71 
Page 75 of 319
The information  display in the
instrument  panel shows  you the
engine  oil life  and  maintenance
service  items when the ignition
switch  is in  the  ON  (II) position.  This
information  helps to keep  you aware
of  the  periodic  maintenance  your
vehicle  needs for continued  trouble-
free  driving.  Refer to page  for
more  information.
Your 
vehicl e’s on board  diagnostic
system  will detect  a loose  or missing
fu el  fill  cap  as an  evaporative  system
leak.  The first  time  a leak  is detected
a  ‘‘CHECK  FUEL CAP’’ message
appears  on the  information  display.
Turn  the engine  off, and  confi rm the
fuel  fill cap  is installed.  If it is,  loosen
it,  then  retighten  it until  it clicks  at
least  once.  The message  should go
off  after  several  days of normal
driving  once you tighten  or replace
the  fuel  fill cap.  To scroll  to another
display,  press the select/reset  knob.
The  ‘‘CHECK  FUEL CAP’’ message
will  appe ar each  time you restart  the
engine  until the system  turns the
message  off. If 
the  system  still detects  a leak  in
the  vehicle’s  evaporative  emissions
system,  the malfunction  indicator
lamp  (MIL)  comes  on. If the  fuel  fill
cap  was  not already  tightened,  turn
the  engine  off, and  check  or
retighten  the fuel  fill cap  until  it
clicks  at least  once.  The MIL  should
go  off  after  several  days of normal
driving once the cap is tightened or
replaced. If the MIL does not go of f ,
have your vehicle inspected by a
dealer. For more inf ormation, see
page . 229
277
Gauges
Maintenance Minder Display
Check Fuel Cap Message
72 
Page 76 of 319
ÎÎ
Î
Î
Î
Î
Î  If equipped.
To 
use  the horn,  press  the pad  around  the ‘‘H’’  logo.
:
1:
Controls  Near the Steering  Wheel
Instru me ntsand Cont ro ls
73
LIGHT  CONTROL
SWITCH HAZARD 
WARNING  BUTTON
WINDSHIELD  WIPERS/
WASHERS
VSA 
OFF SWITCH
STEERING WHEEL
ADJUSTMENT PASSENGER 
AIRBAG
OFF INDICATOR
(P.96)
(P.102) (P.212)
CRUISE CONTROL
MASTER BUTTON
(P.175)
REMOTE AUDIO
CONTROLS(P.138)
(P.78) CRUISE CONTROL
BUTTONS
(P.175) HORN
(P.77)
VTM-4 LOCK(P.204)
(P.35)
(P.77)
(P.74)
MOONROOF BUTTONS
REAR WINDOW
DEFOGGER
(P.75)
HEADLIGHTS/TURN SIGNAL/
FOG LIGHTS
1 1
1
1 
Page 77 of 319
µ
µ
µ
µ µµ
µ
µ µ
MIST
OFF
INT Intermittent
LO Low speed
HI High speed
Windshield washers
Push the right lever up or down to
select a position. The wipers run at high
speed until you release the lever. Rotate the switch clockwise to
turn the rear window wiper ON.
Hold past ON to spray the rear
window washer.
OFF
Hold past OFF to spray the rear 
window washer and turn the rear 
window wiper on for a short
interval.
The wipers run at low speed. The wipers are not activated.
The length of the wiper
interval is varied automatically
according to the vehicle’s speed.
Vary the delay by turning the INT
TIME ring. If you turn it to the
shortest delay, the wiper speed
will increase to low speed
operation when the vehicle speed
exceeds 12 mph (20 km/h).
The wipers run at high speed. Pull the
wiper control lever toward you,
andholdit.Thewashersspray
until you release the lever. The
wipers run at low speed, then
complete one more sweep af ter
you release the lever.
1.
2.
3.
4.
5.
6.
1.
2.
3.
4. Rear Window Wiper and Washer
MIST LO OFF
INT
HI
Windshield Washers
Windshield Wipers and Washers
74 
Page 78 of 319
µ
µ µ
Turn  signal
Off
Parking  and indicator  lights
Headlights
High  beams
Flashhighbeams
Fog  lights  off  (if  equipped)
Fog  lights  on (if equipped) Push 
down  on the
lever  to signal  a left  turn  and  up to
signal  a right  turn. To signal  a lane
ch ange,  push lightly  on the  lever,
and  hold  it. The  lever  will return  to
center  when you release  it or
complete  a turn.
Turning  the switch
on  the  left  lever  to the  position
turns  on the  parking  lights, taillights,
instrument  panel lights,  side-marker
lights,  and rear  license  plate lights.
Turning  the switch  to the
position  turns on the
headlights.  If you  leave  the lights  on
with  the ignition  switch in the
ACCESSORY  (I) or the  LOCK  (0)
position,  you will hear  a reminder
chime  when you open  the driver’s
door. Push the lever
f orward until you hear a click. The
high beam indicator will come on
(see page ). Pull the lever back to
return to the low beams.
You can use the f og lights only when
the headlights are on low beam. Turn the f og lights on and of f by
turning the switch next to the
headlight switch. To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
1.
2.
3.
4.
5.
6.
7.
8. 67
On EX and EX-L models
Turn Signal and Headlights
Turn Signal
Headlights
High Beams
Fog Lights
Inst rument s and Cont rols
75 
Page 79 of 319
The knob on the instrument panel
controls the brightness of the instru-
ment panel lights. Turn the knob to
adjust the brightness.
The automatic lighting of f f eature
turns off the headlights, all other
exterior lights, and the instrument
panel lights within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
go of f . With the driver’s door open,
you will hear a lights-on reminder
chime.
With the headlight switch off, the
high beam headlights come on with
reduced brightness when you turn
the ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes.
On EX and EX-L models
Instrument Panel Brightness
Automatic Lighting Of f Feature
(Canadian Models) Daytime Running L ights
Headlights, Instrument Panel Brightness
76
INSTRUMENT PANEL BRIGHTNESS
CONTROL KNOB 
Page 80 of 319
The rear window def ogger will clear
fog, frost, and thin ice from the
window. Push the def ogger button to
turn it on and off. The indicator
above the button comes on to show
the def ogger is on. If you do not turn
it of f , the def ogger will shut itself of f
af ter about 15 minutes. It also shuts
of f when you turn of f the ignition
switch. You have to turn the
def ogger on again when you restart
the vehicle.The def ogger wires on the inside of
the rear window can be accidentally
damaged. When cleaning the glass,
always wipe side-to-side. Make sure the rear window is clear
and you have good visibility bef ore
starting to drive.
Pushtheredbuttontoturnonthe
hazard warning lights (f our-way
flashers). This causes all four
outside turn signals and both turn
indicators in the instrument panel to
f lash. Use the hazard warning lights
if you need to park in a dangerous
area near heavy traffic, or if your
vehicle is disabled. Hazard Warning Button Rear Window Def ogger
Hazard Warning Button, Rear Window Def ogger
Inst rument s and Cont rols
77
HAZARD WARNING BUTTON
EX and EX-L models
LX models