HUMMER H2 2004 Owners Manual

8. Now connect the black
negative (−) cable to
the negative (−)
terminal of the good
battery. Use a remote
negative (−) terminal
if the vehicle has
one. Your vehicle’s
remote negative (−)
terminal is
marked GND.
Don’t let the other end touch anything until the next
step. The other end of the negative (−) cable
doesn’t go to the dead battery. It goes to a heavy,
unpainted metal engine part or to a remote
negative (−) terminal on the vehicle with the dead
battery.9. Connect the other end
of the negative (−)
cable at least 18 inches
(45 cm) away from
the dead battery, but
not near engine
parts that move.
The electrical connection is just as good there, and
the chance of sparks getting back to the battery
is much less.
10. Now start the vehicle with the good battery and run
the engine for awhile.
11. Try to start the vehicle that had the dead battery. If
it won’t start after a few tries, it probably needs
service.
5-47

Notice:If the jumper cables are removed in the
wrong order, electrical shorting may occur and
damage the vehicle. The repairs would not be
covered by your warranty. Remove the jumper
cables in the correct order, making sure that the
cables do not touch each other or other metal.
A. Heavy, Unpainted Metal Engine Part or Remote
Negative (−) Terminal.
B. Good Battery or Remote Positive (+) and
Negative (−) Terminals.
C. Dead Battery or Remote Positive (+) Terminal.To disconnect the jumper cables from both vehicles do
the following:
1. Disconnect the black negative (−) cable from the
vehicle that had the dead battery.
2. Disconnect the black negative (−) cable from the
vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the other
vehicle.
5. Return the positive (+) remote terminal cover to its
original position.
All-Wheel Drive
Transfer Case
It is not necessary to regularly check transfer case uid
unless you suspect there is a leak or you hear an
unusual noise. A uid loss could indicate a problem.
Have it inspected and repaired.
Refer to the Maintenance Schedule to determine how
often to change the lubricant. SeeScheduled
Maintenance on page 6-4. Jumper Cable Removal
5-48

How to Check Lubricant
A. Filler Plug
B. Drain Plug1. Remove the ller plug (A). The uid level should be
just below the bottom of the ller plug hole. To get
an accurate reading, the vehicle should be on a
level surface.
2. Add uid if necessary.
Refer to the Maintenance Schedule to determine
what kind of lubricant to use. SeeRecommended
Fluids and Lubricants on page 6-12.
3. Reinstall the ller plug. Use care not to overtighten
the ller plug.
5-49

Rear Axle
When to Check Lubricant
It is not necessary to regularly check rear axle uid
unless you suspect there is a leak or you hear an
unusual noise. A uid loss could indicate a problem.
Have it inspected and repaired.
How to Check Lubricant
To get an accurate reading, the vehicle should be on a
level surface.
When the differential is cold, the proper level is from
5/8 inch to 1 5/8 inch (15 mm to 40 mm) below the
bottom of the ller plug hole. Add only enough uid to
reach the proper level.
What to Use
Refer to the Maintenance Schedule to determine what
kind of lubricant to use. SeeRecommended Fluids
and Lubricants on page 6-12.
5-50

Front Axle
When to Check and Change Lubricant
It is not necessary to regularly check front axle uid
unless you suspect there is a leak or you hear an
unusual noise. A uid loss could indicate a problem.
Have it inspected and repaired.
How to Check Lubricant
To get an accurate reading, the vehicle should be on a
level surface.
When the differential is cold, the proper level is from
about 1/4 inch (6 mm) to about 3/8 inch (10 mm) below
the ller plug hole.
What to Use
Refer to the Maintenance Schedule to determine what
kind of lubricant to use. SeeRecommended Fluids
and Lubricants on page 6-12.
5-51

Bulb Replacement
SeeReplacement Bulbs on page 5-58for the proper
type of bulbs to use.
For any bulb changing procedure not listed in this
section, contact your dealer.
Halogen Bulbs
{CAUTION:
Halogen bulbs have pressurized gas inside and
can burst if you drop or scratch the bulb. You or
others could be injured. Be sure to read and
follow the instructions on the bulb package.
Headlamps
1. Open the hood as described earlier underHood
Release on page 5-10and locate the affected
headlamp on the inner front portion of the hood.2. Turn the bulb/socket
retainer (arrow)
counterclockwise to
unlock the bulb/socket.
You may prefer to
unplug the electrical
connector before
removing the bulb/
socket. If so, complete
Step 4 before doing
this step.
3. Pull the bulb/socket
straight out from the
headlamp housing.
5-52

4. Unplug the electrical
connector.
5. Push the new bulb/socket into the headlamp
assembly making sure to align the splines on
the bulb/socket with the splines in the headlamp
housing. Use care not to touch the bulb with
your ngers or hands.
6. Turn the bulb/socket retainer clockwise to lock the
bulb/socket in place.
7. Plug in the electrical connector.Front Turn Signal and Parking
Lamps
1. Open the hood as described earlier underHood
Release on page 5-10and locate the affected lamp.
2. Turn the bulb socket
counterclockwise and
remove it from the lamp
housing.
3. Pull the bulb from the bulb socket.
4. Put the new bulb into the bulb socket.
5. Put the bulb socket into the lamp housing and turn
it clockwise until it locks.
5-53

Sidemarker Lamps
It is recommended that these components be replaced
by your dealer.
Daytime Running Lamps
1. Locate the lamp
assembly behind the
front bumper. It is
easiest to come in from
the side of the
vehicle through the
wheel opening.2. Turn the bulb socket
counterclockwise and
remove it from the lamp
housing.
3. Remove the bulb from the bulb socket.
4. Put the new bulb into the bulb socket.
5. Put the bulb socket into the lamp housing and turn
it clockwise until it locks.
5-54

Roof Marker Lamps
Corner Roof Marker Lamps
1. Remove the screw and lift off the lens.2. Turn the socket counterclockwise to remove it and
remove the old bulb.
3. Put a new bulb into the socket.
4. Reinstall the socket into the lens and turn it
clockwise to lock it into place.
5. Hook the side of the lens with the hook end in the
notch rst and then tighten the screw.
5-55

Center Roof Marker Lamps
1. Push in on the notch with a at tool and pull the
lamp out.
2. Turn the bulb socket counterclockwise and remove
it from the lamp housing.
3. Remove the bulb from the bulb socket.
4. Put the new bulb into the bulb socket.
5. Place the hook end of the lamp in place on one
side and push the other end of the lamp down
until it locks in place.
5-56