flat tire HUMMER H2 2004 Owners Manual

Power Winch Platform (If Equipped)
You can use the power winch platform with an
aftermarket winch. Connect the winch to the platform
and wiring to the vehicle following the winch
manufacturer’s guidelines.
1. Slide the winch platform into the front receiver of
your vehicle. To secure it, follow the next step.
You will be using the locking pin (if equipped) stored
with the jack/tool kit. SeeChanging a Flat Tire on
page 5-79for more information on location.
2. Slide the pin down through the hole in the front
bumper and into the receiver.If you look under the
receiver, you will see the
locking portion (clip) of the
pin coming through the
bottom hole in the receiver.
3. Turn the clip so that it is
perpendicular to the
pin. Pin is shown off the
vehicle for clarity.
4-62

Tires..............................................................5-60
Ination - Tire Pressure.................................5-68
Tire Inspection and Rotation...........................5-69
When It Is Time for New Tires.......................5-70
Buying New Tires.........................................5-71
Uniform Tire Quality Grading..........................5-72
Wheel Alignment and Tire Balance..................5-73
Wheel Replacement......................................5-74
Tire Chains..................................................5-75
Accessory Inator.........................................5-76
If a Tire Goes Flat........................................5-78
Changing a Flat Tire.....................................5-79
Spare Tire...................................................5-92
Appearance Care............................................5-92
Cleaning the Inside of Your Vehicle.................5-93
Care of Safety Belts......................................5-95
Weatherstrips...............................................5-95Cleaning the Outside of Your Vehicle..............5-95
Sheet Metal Damage.....................................5-98
Finish Damage.............................................5-99
Underbody Maintenance................................5-99
Chemical Paint Spotting.................................5-99
Vehicle Care/Appearance Materials................5-100
Vehicle Identication.....................................5-101
Vehicle Identication Number (VIN)................5-101
Service Parts Identication Label...................5-101
Electrical System..........................................5-101
Add-On Electrical Equipment.........................5-101
Windshield Wiper Fuses...............................5-102
Power Windows and Other Power Options......5-102
Fuses and Circuit Breakers..........................5-102
Capacities and Specications........................5-111
Section 5 Service and Appearance Care
5-2

After the tires have been rotated, adjust the front and
rear ination pressures as shown on the
Certication/Tire label or Tire and Loading Information
label. SeeLoading Your Vehicle on page 4-67.
Make certain that all wheel nuts are properly tightened.
See “Wheel Nut Torque” underCapacities and
Specications on page 5-111.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after a time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
places where the wheel attaches to the vehicle.
In an emergency, you can use a cloth or a
paper towel to do this; but be sure to use a
scraper or wire brush later, if you need to, to
get all the rust or dirt off. See “Changing a Flat
Tire” in the Index.
When It Is Time for New Tires
One way to tell when it’s
time for new tires is to
check the treadwear
indicators, which will
appear when your tires
have only 1/16 inch
(1.6 mm) or less of tread
remaining. Some
commercial truck tires may
not have treadwear
indicators.
5-70

Wheel Replacement
Replace any wheel that is bent, cracked or badly rusted
or corroded. If wheel nuts keep coming loose, the
wheel, wheel bolts and wheel nuts should be replaced.
If the wheel leaks air, replace it (except some
aluminum wheels, which can sometimes be repaired).
See your dealer if any of these conditions exist.
Your dealer will know the kind of wheel you need.
Each new wheel should have the same load-carrying
capacity, diameter, width, offset and be mounted
the same way as the one it replaces.
If you need to replace any of your wheels, wheel bolts
or wheel nuts, replace them only with new GM
original equipment parts. This way, you will be sure to
have the right wheel, wheel bolts and wheel nuts
for your vehicle.{CAUTION:
Using the wrong replacement wheels, wheel
bolts or wheel nuts on your vehicle can be
dangerous. It could affect the braking and
handling of your vehicle, make your tires lose
air and make you lose control. You could have
a collision in which you or others could be
injured. Always use the correct wheel, wheel
bolts and wheel nuts for replacement.
Notice:The wrong wheel can also cause problems
with bearing life, brake cooling, speedometer or
odometer calibration, headlamp aim, bumper height,
vehicle ground clearance and tire or tire chain
clearance to the body and chassis.
SeeChanging a Flat Tire on page 5-79for more
information.
5-74

If a Tire Goes Flat
It’s unusual for a tire to “blowout” while you’re driving,
especially if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But if you should ever have a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the at tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and grip the steering wheel rmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use
in a skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop, well off the road if possible.{CAUTION:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous without
the appropriate safety equipment and training.
The jack provided with your vehicle is
designed only for changing a at tire. If it is
used for anything else, you or others could be
badly injured or killed if the vehicle slips off
the jack. Use the jack provided with your
vehicle only for changing a at tire.
If a tire goes at, the next part shows how to use your
jacking equipment to change a at tire safely.
5-78

Changing a Flat Tire
If a tire goes at, avoid further tire and wheel damage
by driving slowly to a level place. Turn on your
hazard warning ashers.
{CAUTION:
Changing a tire can be dangerous. The vehicle
can slip off the jack and roll over or fall on you
or other people. You and they could be badly
injured or even killed. Find a level place to
change your tire. To help prevent the vehicle
from moving:
1. Set the parking brake rmly.
2. Put the shift lever in PARK (P).
3. Turn off the engine and do not restart
while the vehicle is raised.
CAUTION: (Continued)
CAUTION: (Continued)
4. Do not allow passengers to remain in the
vehicle.
5. Put the wheel blocks at the front and rear
of the tire farthest away from the one
being changed. That would be the tire on
the other side, at the opposite end of the
vehicle.
5-79

The following steps will tell you how to use the jack and
change a tire.
Removing the Spare Tire and Tools
The equipment you’ll need is behind and to the side of
the driver’s side second row seat. To remove the
equipment, do the following:
1. Fold the driver’s side second row seat down. See
60/40 Split Bench Seat on page 1-8.
2. Turn the wingnut (A),
which holds the jack,
counterclockwise
to release the jack.
3. Turn the wingnut (B), which holds the jack tool kit,
counterclockwise to release it.Open the tool bag and you will nd the following tools
which you will use to remove the spare tire and at tire:
A. Jack Handle Extension (Used for Rear Flats Only)
B. Jack Handle
C. Wheel Wrench
D. Ratchet
E. Spanner Wrench
F. Locking Pin (If Equipped) Not used for tire changing
procedure. See “Power Winch Platform” underIf You
Are Stuck: In Sand, Mud, Ice or Snow on page 4-56.
5-80

The spare tire and wheel blocks are stored in the rear
cargo area. Remove the tire cover to get to them.
A. Spare or Flat Tire
B. Receiver Extension (If Equipped) Not used for tire
changing procedure. See “Receiver Extension” under
If You Are Stuck: In Sand, Mud, Ice or Snow on
page 4-56.
C. Tire Retainer Plate
D. Nut
E. Wheel BlocksFollow the instructions to remove the wheel blocks and
spare tire:
1. Remove the wheel blocks from the tire retainer
plate by turning the wingnut counterclockwise.
2. Place the at end of the wheel wrench through the
hole in the spanner wrench.
5-81

Removing the Flat Tire and Installing
the Spare Tire
1. To remove the center
cap, place the at end
of the wheel wrench
in the slot on the wheel
and gently pry the
center cap out.
2. Slide the ratchet onto the wheel wrench with the
DOWN mark facing you.
3. Turn the ratchet counterclockwise to loosen the
wheel nuts. Don’t remove them yet.
You will now need to jack the vehicle up using the
instructions following.
4. Assemble the jack and tools as follows:
Front Flat Tire:Attach the jack handle (E) with the
hook end connected to the u-hook/clevis on the
jack (A). Slide the ratchet (F) onto the jack handle (E)
with the UP mark facing you.
5-83

Rear Flat Tire:Attach the jack handle extension (D)
to the jack handle (E) and then press the clip (arrow)
so it engages. Then attach the jack handle (E) with
the hook end connected to the u-hook/clevis on the
jack (A). Slide the ratchet (F) onto the jack handle
extension (D) with the UP mark facing you.
5. Turn the ratchet (F) clockwise to raise the jack
head to the lifting point.Front Flat Tire:Position
the jack under the vehicle
on the frame behind
the at tire where the
frame sections overlap.
See the graphic following
for an approximate
measurement of the jack
location on the frame.
Front Position
5-84