clock HUMMER H2 2006 Owner's Guide

Page 426 of 502

14. Tighten the nuts rmly
in a crisscross
sequence as shown by
turning the wheel
wrench with the wheel
wrench extender
clockwise.
15. When you install the wheel and tire, you must also
reinstall the center cap. Place the cap on the wheel
and tap it into place until it sits ush with the wheel.
Storing a Flat or Spare Tire and
Tools (SUT)
Storing the Flat or Spare Tire (SUT)
Use the following art and text to help you store the
spare or at tire back into its proper location when you
are done.To store the at or spare tire on the tire carrier, do the
following:
1. Close the tire carrier. SeeTailgate/Spare Tire
Carrier on page 2-14for tire carrier operation.
2. Place the at or spare tire onto the tire carrier with
the outside of the wheel facing you.
3. Reinstall the three nuts holding spare or at tire to
the tire carrier. Tighten the nuts by hand.
4. Use the ratchet and wheel wrench (jack A) to
tighten the nuts rmly.
Jack A Tools
5-96

Page 428 of 502

Storing the Jack A and Tools (SUT)
Follow these instructions to store jack A and tools:
1. Lower the jack completely.
2. Place the jack (B) in the mounting bracket in the
rear cargo compartment.3. Tighten the wing nut (C) until the jack is securely
fastened.
In order to reduce the potential of the jack
squeaking or rattling, you will need to preload the
jack so it ts tightly in the mounting bracket.
To do this, turn the u-hook/clevis at the top of the
jack clockwise until the jack is held tight in the
mounting bracket.
4. Place the wheel blocks (E) onto the mounting stud
and tighten the wing nut (D) to secure them.
5. Place the tools in the tool bag (A), roll the bag
together tightly and neatly and then close it with
the hook and loop fasteners.
If you do not roll the tool bag tightly and neatly, you
will have trouble getting it back into the storage
retention clips in the next step.
5-98

Page 430 of 502

8. Replace the jack cover. Be sure the tabs on the
back of the jack cover t into the slots on the
cargo box before closing the jack cover.
9. Lock the cover.
10. Close the spare tire carrier to ensure it securely
latches. SeeTailgate/Spare Tire Carrier on
page 2-14for tire carrier operation.
Storing the Jack B and Tools (SUT)
Follow these instructions to store jack B and tools:
1. Lower the jack completely.
2. Place the jack in the mounting bracket.
3. Turn the u-hook/clevis at the top of the jack
clockwise until the jack is held tight in the
mounting bracket.
4. Push and pull on the jack and retighten if necessary
to make sure the jack is secure.
5. Place the wheel blocks in the tool bag.
6. Place the remaining tools in the tool bag.
5-100

Page 433 of 502

5. Slide the license plate holder onto the spare or at
tire. Secure it from the back of the tire carrier with
the wing nut.
If you choose not to reinstall the spare or at tire on
the vehicle, you will still need to reinstall the
license plate holder on the spare tire carrier.
Storing the Jack (A or B) and
Tools (SUV)
Follow these instructions to store the jack A and tools:
1. Lower the jack completely.
2. For jack A, place the wheel blocks together and
install behind the jack.
3. Place the jack in the mounting bracket.
4. Tighten the wing nut for jack A until the jack and
wheel blocks are securely fastened. For jack B, turn
the u-hook/clevis at the top of the jack clockwise until
the jack is held tight in the mounting bracket.
Jack AJack B
5-103

Page:   < prev 1-10 11-20 21-30 31-40