headlamp HUMMER H2 2007 Owners Manual

Q(Lock):Press this button once to lock all of the
doors. Pressing lock again within three seconds
may cause the horn to chirp for lock conrmation.
You can choose different feedback options for each
press of the lock button. See “Lock Feedback” and
“Unlock Feedback” underDIC Vehicle
Customization on page 234for more information.
L(Panic):Press this button to sound the horn
and ash the headlamps and taillamps for up
to 30 seconds. Panic can be turned off by pressing
the button again, by waiting for 30 seconds, or
by starting the vehicle.
Matching Transmitter(s) to Your Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking your vehicle. If a
transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring
any remaining transmitters with you when you go to
your dealer. When the dealer matches the
replacement transmitter to your vehicle, any
remaining transmitters must also be matched. Once
your dealer has coded the new transmitter, the lost
transmitter will not unlock your vehicle. Each
vehicle can have a maximum of four transmitters
matched to it.
Battery Replacement
Under normal use, the battery in your
RKE transmitter should last about two years.
You can tell the battery is weak if the transmitter
will not work at the normal range in any location.
If you have to get close to your vehicle before the
transmitter works, it is probably time to change
the battery.
Notice:When replacing the battery, use
care not to touch any of the circuitry. Static
from your body transferred to these surfaces
may damage the transmitter.
98

Content Theft-Deterrent
Your vehicle is equipped with a content
theft-deterrent alarm system.
With this system, the
security light in the
instrument panel cluster
will ash as you open
the door if your
ignition is off.
This light reminds you to activate the
theft-deterrent system. Here is how to do it:
1. Open the door.
2. Lock the door with the power door lock switch
or the remote keyless entry transmitter. The
security light will illuminate to inform the driver
the system is arming. If a door is open when
the doors are locked, the security light
will ash.3. Close all doors. The security light should go
off after about 30 seconds. The alarm is not
armed until the security light goes off.
If the delayed locking feature is turned on,
the theft-deterrent system will not start
the arming process until the last door is
closed and the delay timer has expired.
SeeDelayed Locking on page 102.
If a locked door is opened without the key or
the remote keyless entry transmitter, the alarm will
go off. The headlamps and parking lamps will
ash for two minutes, and the horn will sound for
30 seconds, then will turn off to save the battery
power. You can choose different feedback options
for the alarm. SeeDIC Vehicle Customization
on page 234.
Remember, the theft-deterrent system will not
activate if you lock the doors with the vehicle’s key
or use the manual door lock. It activates only if
you use a power door lock switch with the
door open, or with the remote keyless entry
transmitter. You should also remember that you
can start your vehicle with the correct ignition key if
the alarm has been set off.
116

Here is how to avoid setting off the alarm
by accident:
If you do not want to activate the
theft-deterrent system, the vehicle should be
locked with the door keyafterthe doors
are closed.
Always unlock a door with a key, or use the
remote keyless entry transmitter. Unlocking
a door any other way will set off the alarm.
If you set off the alarm by accident, unlock any
door with the key. You can also turn off the alarm
by pressing unlock on the remote keyless entry
transmitter. The alarm will not stop if you try
to unlock a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, lower the driver’s
window and open the driver’s door.
2. Activate the system by locking the doors with
the power door lock switch while the door is
open, or with the remote keyless entry
transmitter.
3. Get out of the vehicle, close the door and wait
for the security light to go out.
4. Then reach in through the window, unlock the
door with the manual door lock and open the
door. This should set off the alarm.
While the alarm is set, the power door unlock
switch is not operational.
If the alarm does not sound when it should but the
headlamps ash, check to see if the horn works.
The horn fuse may be blown. To replace the fuse,
seeInstrument Panel Fuse Block on page 504
andUnderhood Fuse Block on page 507.
If the alarm does not sound or the headlamps do
not ash, the vehicle should be serviced by
your dealer.
117

Outside Automatic Dimming Mirror
with Curb View Assist
If the vehicle has this feature, the driver’s outside
mirror adjusts for the glare of the headlamps behind
you. SeeAutomatic Dimming Rearview Mirror with
Compass and Temperature Display on page 139.
The vehicle’s outside mirrors can also perform a
curb view assist mirror function. This causes
the passenger’s and/or driver’s mirror to tilt to a
preselected position when the vehicle is in
REVERSE (R). This feature may be useful in
viewing the curb when parallel parking.
When the vehicle is shifted out of REVERSE (R)
and a short delay has occurred, the passenger’s
and/or driver’s mirror will return to its original
position.
To change the preselected tilt position, adjust the
mirrors to the desired position while the vehicle
is in REVERSE (R). When the vehicle is shifted out
of REVERSE (R), this new position is saved in
memory as the tilt position.
This feature can be enabled/disabled through the
Driver Information Center. SeeDIC Vehicle
Customization on page 234for more information.
OnStar®System
OnStar®uses several innovative technologies and
live advisors to provide you with a wide range
of safety, security, information, and convenience
services. If your airbags deploy, the system is
designed to make an automatic call to OnStar
®
Emergency advisors who can request emergency
services be sent to your location. If you lock
your keys in the vehicle, call OnStar
®at
1-888-4-ONSTAR and they can send a signal to
unlock your doors. If you need roadside
assistance, press the OnStar
®button and they
can contact Roadside Service for you.
144

Instrument Panel Overview........................ 174
Hazard Warning Flashers.......................... 176
Other Warning Devices............................. 177
Horn.......................................................... 177
Tilt Wheel.................................................. 177
Turn Signal/Multifunction Lever.................. 178
Turn and Lane-Change Signals................. 178
Headlamp High/Low-Beam Changer.......... 179
Flash-to-Pass............................................ 180
Windshield Wipers..................................... 180
Windshield Washer.................................... 181
Rear Window Wiper/Washer (SUV)........... 182
Cruise Control........................................... 183
Exterior Lamps.......................................... 186
Headlamps on Reminder........................... 188
Daytime Running Lamps (DRL)................. 188
Automatic Headlamp System..................... 189
Off-Road Lamps........................................ 190
Instrument Panel Brightness...................... 191
Dome Lamps............................................. 191
Dome Lamp Override................................ 191Entry/Exit Lighting...................................... 191
Reading Lamps......................................... 192
Battery Run-Down Protection..................... 192
Rear Vision Camera.................................. 192
Accessory Power Outlet(s)........................ 196
Ashtray(s) and Cigarette Lighter................ 197
Climate Controls......................................... 197
Dual Automatic Climate Control System....... 197
Outlet Adjustment...................................... 203
Warning Lights, Gages, and Indicators........ 204
Instrument Panel Cluster........................... 205
Speedometer and Odometer...................... 206
Trip Odometer........................................... 206
Tachometer............................................... 206
Safety Belt Reminder Light........................ 206
Airbag Readiness Light............................. 207
Airbag Off Light......................................... 208
Charging System Light.............................. 209
Voltmeter Gage......................................... 210
Brake System Warning Light..................... 211
Anti-Lock Brake System Warning Light...... 212
Section 3 Instrument Panel
171

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane Change Signals.Turn and
Lane-Change Signals on page 178.
53Headlamp High/Low-Beam Changer.
Headlamp High/Low-Beam Changer on
page 179.
Flash-to-Pass Feature. SeeFlash-to-Pass on
page 180.
NWindshield Wipers. SeeWindshield
Wipers on page 180.
LWindshield Washer. SeeWindshield
Washer on page 181.
ICruise Control.Cruise Control on
page 183.
For information on the exterior lamps, seeExterior
Lamps on page 186later in this section.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever will
return automatically.
To signal a lane change, raise or lower the lever for
less than one second until the arrow starts to ash.
This will cause the turn signals to automatically
ash three times. It will ash six times if the
tow-haul mode is active. Holding the turn signal
lever for more than one second will cause the turn
signals to ash until you release the lever. The lever
will return by itself when it is released.
178

An arrow on the
instrument panel
cluster will ash in the
direction of the turn
or lane change.
As you signal a turn or a lane change, if the
arrows ash more quickly than normal, a signal
bulb may be burned out and other drivers will not
see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows do not go on at all when you
signal a turn, check for burned-out bulbs and a
blown fuse. SeeInstrument Panel Fuse Block on
page 504andUnderhood Fuse Block on page 507.Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a
mile (1.2 km), a chime will sound at each ash
of the turn signal and the message TURN SIGNAL
ON will also appear in the DIC. SeeDIC
Warnings and Messages on page 226. To turn the
chime and message off, move the turn signal
lever to the off position.
Headlamp High/Low-Beam Changer
53(Headlamp High/Low Beam Changer):
To change the headlamps from low to high beam,
push the lever toward the instrument panel. To
return to low-beam headlamps, pull the
multifunction lever toward you. Then release it.
When the high beams
are on, this indicator light
on the instrument panel
cluster will also be on.
179

Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you that
you want to pass. It works even if your headlamps
are in the automatic position.
To use it, pull the turn signal lever toward you,
then release it.
If your headlamps are in the automatic position or
on low beam, your high-beam headlamps will
turn on. They will stay on as long as you hold the
lever toward you. The high-beam indicator on
the instrument panel cluster will come on. Release
the lever to return to normal operation.
Windshield Wipers
You control the windshield wipers by turning the
band with the wiper symbol on it.
8(Mist):For a single wiping cycle, turn the
band to mist. Hold it there until the wipers
start. Then let go. The wipers will stop after
one wipe. If you want more wipes, hold the
band on mist longer.
6(Delay):You can set the wiper speed for a long
or short delay between wipes. This can be very
useful in light rain or snow. Turn the band to
choose the delay time. The closer to the top of the
lever, the shorter the delay.
6(Low Speed):For steady wiping at low
speed, turn the band away from you to the
rst solid band past the delay settings.
1(High Speed):For high-speed wiping, turn
the band further, to the second solid band past the
delay settings.
9(Off):To stop the wipers, move the band
to off.
Be sure to clear ice and snow from the wiper
blades before using them. If they are frozen to the
windshield, carefully loosen or thaw them. If
your blades do become worn or damaged, get
new blades or blade inserts.
180

Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
LQ(Washer Fluid):There is a paddle marked
with the windshield washer symbol at the top of
the multifunction lever. Push the paddle to
spray washer uid on the windshield. The wipers
will clear the window and then either stop or
return to the preset speed.
_(Heated Washer Fluid):If your vehicle has
the heated windshield washer uid system, it
is used to help clear ice, snow, tree sap, or bugs
from your windshield.To activate Automatic mode for de-icing, press the
heated washer button located above the
headlamp switch on the left side of the dash.
Pushing the heated washer uid button will
activate the heated windshield washer uid
system. This activation will initiate four heated
wash/wipe cycles. The rst heated wash/wipe
cycle may take up to 40 seconds to occur,
depending on outside temperature. After the rst
wash/wipe cycle, it may take up to 20 seconds
for each of the remaining cycles. The heated
windshield washer uid system may be turned off
at any time by pushing the button again prior
to the completion of 4 wash/wipe cycles.
When the heated windshield washer uid system
is activated under certain outside temperature
conditions, steam may ow out of the washer
nozzles for a short period of time before washer
uid is sprayed. This is a normal condition.
A message will be displayed on the Driver
Information Center (DIC) when the washer uid is
low. SeeDIC Warnings and Messages on
page 226.
181

The exterior lamp control has four positions:
O(Off):Turn the knob to this position to turn off
all exterior lamps including the DRL. This
control will spring back to AUTO when released.
AUTO (Automatic):Turn the control to this
position to put the system into automatic headlamp
mode. AUTO mode, if enabled, will turn the
exterior lamps, including your DRL, on and off
automatically depending on how much light
is available outside the vehicle.
Your automatic lights may be disabled even if the
control is in the AUTO position.
To enable automatic lighting, do any of the
following:
Turn the headlamp control from AUTO to off
and release the control. It will return back to
the AUTO position by itself.
Turn the headlamp control from the parking
lamp position to AUTO.
Turn the headlamp control from the headlamp
position to AUTO.
Turn your engine off and then on again with
the headlamp control in AUTO.To disable automatic lighting, do any of the
following:
Turn the headlamp control from AUTO to off
and release the control. It will return back to
the AUTO position by itself.
Turn the headlamp control from AUTO to the
parking lamp position.
Turn the headlamp control from AUTO to the
headlamp position.
;(Parking Lamps):Turn the control to this
position to turn on the parking lamps, together with
the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Roof Marker Lamps
Instrument Panel Lights
187