HUMMER H2 2008 Owners Manual

2. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. It can usually be found where the
hanging antenna wire is attached to the motor-head
unit and may be a colored button. Press this
button. After you press this button, you will have
30 seconds to complete the following steps.3. Immediately return to your vehicle. Press and hold
the Universal Home Remote button that you would
like to use to control the garage door until the
garage door moves. The indicator light, above the
selected button, should slowly blink. You may
need to hold the button from ve to 20 seconds.
4. Immediately, within one second, release the button
when the garage door moves. The indicator light
will blink rapidly until programming is complete.
5. Press and release the same button again.
The garage door should move, conrming
that programming is successful and complete.
To program another Rolling Code device such as an
additional garage door opener, a security device,
or home automation device, repeat Steps 1-5, choosing
a different function button in Step 3 than what you
used for the garage door opener.
If these instructions do not work, you probably have
a Fixed Code garage door opener. Follow the
Programming instructions that follow for a Fixed Code
garage door opener.
2-59

Programming Universal Home
Remote — Fixed Code
If you have questions or need help programming the
Universal Home Remote System, call 1-866-572-2728 or
go to www.learcar2u.com.
Most garage door openers sold before 1996 are
Fixed Code units.
Programming a garage door opener involves
time-sensitive actions, so read the entire procedure
before you begin. If you do not follow these actions,
the device will time out and you will have to repeat
the procedure.To program up to three devices:
1. To verify if you have a Fixed Code garage door
opener, remove the battery cover on your hand
held transmitter supplied by the manufacturer
of your garage door opener motor. If you see a row
of dip switches similar to the graphic above, you
have a Fixed Code garage door opener. If you
do not see a row of dip switches, return to the
previous section for Programming Universal Home
Remote – Rolling Code.
Your hand held transmitter may have between
eight to 12 dip switches depending on the brand of
transmitter.
2-60

Your garage door opener receiver (motor head unit)
may also have a row of dip switches that can be
used when programming the Universal Home
Remote. If the total number of switches on the motor
head and hand held transmitter are different, or if
the dip switch settings are different, use the
dip switch settings on the motor head unit to
program your Universal Home Remote. The motor
head dip switch settings can also be used when
you do not have the original hand held transmitter.
Your panel of switches may not appear exactly as
they do in the examples above, but they should
be similar.
The switch positions on your hand-held transmitter
may be labeled, as follows:
A switch in the up position may be labeled as
“Up,” “+,” or “On.”
A switch in the down position may be labeled
as “Down,” “−,” or “Off.”
A switch in the middle position may be labeled
as “Middle,” “0,” or “Neutral.” Example of Eight Dip Switches with Two Positions
Example of Eight Dip Switches with Three Positions
2-61

2. Write down the eight to 12 switch settings from
left to right as follows:
When a switch is in the up position, write “Left.”
When a switch is in the down position, write
“Right.”
If a switch is set between the up and down
position, write “Middle.”
The switch settings that you wrote down in
Step 2 will now become the button strokes you
enter into the Universal Home Remote in
Step 4. Be sure to enter the switch settings that
you wrote down in Step 2, in order from left
to right, into the Universal Home Remote, when
completing Step 4.
3. From inside your vehicle, rst rmly press all three
buttons at the same time for about three seconds.
Release the buttons to put the Universal Home
Remote into programming mode.4. The indicator lights will blink slowly. Enter each
switch setting from Step 2 into your vehicle’s
Universal Home Remote. You will have
two and one-half minutes to complete Step 4.
Now press one button on the Universal Home
Remote for each switch setting as follows:
If you wrote “Left,” press the left button in the
vehicle.
If you wrote “Right,” press the right button in the
vehicle.
If you wrote “Middle,” press the middle button in
the vehicle.
2-62

5. After entering all of the switch positions, again,
rmly press and release all three buttons at the
same time. The indicator lights will turn on.
6. Press and hold the button you would like to use to
control the garage door until the garage door
moves. The indicator light above the selected button
should slowly blink. You may need to hold the
button from ve to 55 seconds.
7. Immediately release the button when the garage
door moves. The indicator light will blink rapidly
until programming is complete.
8. Press and release the same button again.
The garage door should move, conrming
that programming is successful and complete.
To program another Fixed Code device such as an
additional garage door opener, a security device,
or home automation device, repeat Steps 1-8, choosing
a different button in Step 6 than what you used for
the garage door opener.
Using Universal Home Remote
Press and hold the appropriate button for at least
half of a second. The indicator light will come on while
the signal is being transmitted.
Reprogramming Universal Home
Remote Buttons
You can reprogram any of the three buttons by repeating
the instructions.
Erasing Universal Home Remote
Buttons
You should erase the programmed buttons when you
sell or terminate your lease.
To erase either Rolling Code or Fixed Code on the
Universal Home Remote device:
1. Press and hold the two outside buttons at the same
time for approximately 20 seconds, until the
indicator lights, located directly above the buttons,
begin to blink rapidly.
2. Once the indicator lights begin to blink, release both
buttons. The codes from all buttons will be erased.
For help or information on the Universal Home Remote
System, call the customer assistance phone number
underCustomer Assistance Offices on page 7-5.
2-63

Storage Areas
Glove Box
To open the glove box, lift up on the lever.
Cupholder(s)
Your vehicle has cupholders located in front of the
center console, in the rear center armrest, and in the
rear of the vehicle on the left side.
Center Console Storage
Your vehicle has a center console located between the
front seats. To open, press the button and lift up.
2-64

Luggage Carrier
If your vehicle has this feature, you can load cargo on
your vehicle.
The luggage carrier consists of siderails attached to the
roof. The crossrails attach into the siderails and can
be moved back and forth to accommodate securing
various cargo sizes.
See your dealer/retailer for more information.
Notice:Loading cargo on the luggage carrier that
weighs more than 300 lbs. (136 kg) or hangs over the
rear or sides of the vehicle may damage your vehicle.
Load cargo only on top of the crossrails and tie the
cargo down to the crossrail support cargo tie-down
loops, making sure to fasten it securely.
Do not exceed the maximum vehicle capacity when
loading your vehicle. For more information on vehicle
capacity and loading, seeLoading Your Vehicle on
page 4-44.
Rear Seat Armrest
Your vehicle has a rear seat armrest with cupholders.
To access, pull the tab on the armrest forward.
Cargo Tie Downs (SUT)
There are four oval shaped openings (A) in the cargo
bed that allow access to four tie downs. You can
use these tie downs to secure cargo.
2-65

All-Weather Cargo Area (SUT)
Your vehicle has features to help it resist the elements
and protect cargo inside the cargo area.
Even when the water management system is working
properly and the cover system is on, there may be some
instances (heavy rains, automated car washes, etc.)
when water may be present in the drain holes.
See “Cargo Area Floor Drains” later in this section for
more information.
Removal and Cleaning
To ensure that the water management system performs
properly, be sure that the midgate, tailgate and cover
system are fully closed and that each element of
the water management system is clean and not blocked
with debris. Follow the instruction given next in this
section for the proper procedures on cleaning each item
of the water management system.
Side Rail Channels
The side rail channels are located on top of both sides
of the roof and the cargo area. You may want to
ush them out with clean water if you notice any debris
collecting inside of them.
When loading cargo into the cargo area, be careful not
to damage the rails.
For more information on this feature seeLuggage
Carrier on page 2-65.
2-66

Cargo Area Floor Drains
Your vehicle also has four cargo-area oor drains (A)
located under the cargo mat, if it has this feature,
near the sides of the cargo area. These drains should
be cleaned periodically to allow water to exit the
cargo area.The cargo mat has cutouts for the drains. You can ush
the drains through the cutouts, but if the cargo area
is extremely dirty you can lift up the edges of the cargo
oor mat or take the whole mat out and ush the
drains with water. The drain grates can be removed to
clear any debris that has accumulated in the drain.
Sunroof
The vehicle may have a
power sliding sunroof.
The ignition must be on or
in the accessory position,
or Retained Accessory
Power (RAP) must be
active.
SeeRetained Accessory Power (RAP) on page 2-29.
The switch used to operate the sunroof is located in the
overhead console.
2-67

Express-Open/Close Sunroof
The sunroof has a feature which allows the sunroof
panel to be opened or closed without continuously
pressing the switch. The express-open can be stopped
at any time by pushing the front of the switch a
second time.
The sunroof has four positions:
Comfort open stop:To open the sunroof and
sunshade, press the rear of the switch quickly and
release. The glass panel will open to an interim
position that reduces wind noise. For information on
using the sunshade, see “Sunshade Operation” later.
Full open stop:To open the sunroof further, press
the rear of the switch quickly once more.
Express close:To close the sunroof, press the front
of the switch quickly and release.
Vent:The vent position allows the rear of the sunroof
to be opened and tilted upward. With the sunroof in
the fully closed position, press and hold the front of
the switch until the sunroof reaches the desired vent
position or until it stops moving. To close the sunroof
from the vent position, press and hold the rear of the
switch until the sunroof is fully closed.
Do not leave the sunroof open for long periods of time
as debris may collect in the tracks.
Anti-Pinch Protection Feature
If something gets caught between the glass panel and
roof frame while the sunroof is closing, the glass
panel will stop and open half way, and the deector will
raise fully.
If something gets caught between the glass panel and
the roof frame during the tilt down operation, the
glass panel will stop and open fully.
If the sunroof panel receives a strong impact, the
anti-pinch protection feature may work even if nothing
gets caught between the glass panel and roof frame.
Sunshade Operation
The sunshade will open automatically when opening the
sunroof.
However, it can manually be pulled shut after the
sunroof is closed. To adjust the sunshade, push it
backward or pull it forward to the desired position.
The sunshade cannot be adjusted further than
the current closed position of the sunroof.
Notice:If you force the sunshade forward of the
sliding glass panel, damage will occur and the
sunroof may not open or close properly. Always
close the glass panel before closing the sunshade.
2-68