spare wheel HUMMER H3 2006 Owners Manual

Off-Road Driving
This off-road guide is meant to provide advice for when
you drive your vehicle off paved roads. Also, see
Braking on page 4-6.
Off-road driving can be great fun. But it does have
some denite hazards. The greatest of these is
the terrain itself.
“Off-roading” means you have left the great North
American road system behind. Traffic lanes are not
marked. Curves are not banked. There are no
road signs. Surfaces can be slippery, rough, uphill or
downhill. In short, you have gone right back to nature.
Off-road driving involves some new skills. And that
is why it is very important that you read this guide.
You will nd many driving tips and suggestions.
These will help make your off-road driving safer
and more enjoyable.
Before You Go Off-Roading
There are some things to do before you go out. For
example, be sure to have all necessary maintenance
and service work done. Check to make sure all
underbody shields are properly attached. Make sure any
equipment you may need — rst aid kit, cell phone,
ashlight, etc. — is securely stored in the vehicle.
Be sure you read all the information about your
four-wheel-drive vehicle in this manual. Is there enough
fuel? Is the spare tire fully inated? Are the uid
levels up where they should be? What are the local
laws that apply to off-roading where you will be driving?
If you do not know, you should check with law
enforcement people in the area. Will you be on
someone’s private land? If so, be sure to get the
necessary permission.
4-17

Buying New Tires.........................................5-66
Different Size Tires and Wheels......................5-67
Uniform Tire Quality Grading..........................5-68
Wheel Alignment and Tire Balance..................5-69
Wheel Replacement......................................5-69
Tire Chains..................................................5-71
If a Tire Goes Flat........................................5-72
Changing a Flat Tire.....................................5-73
Removing the Spare Tire and Tools................5-75
Removing the Flat Tire and Installing the
Spare Tire................................................5-77
Storing a Flat or Spare Tire and Tools................5-82
Spare Tire...................................................5-84
Appearance Care............................................5-85
Cleaning the Inside of Your Vehicle.................5-85
Fabric/Carpet...............................................5-87
Leather.......................................................5-87
Instrument Panel, Vinyl, and Other
Plastic Surfaces........................................5-88
Care of Safety Belts......................................5-88
Weatherstrips...............................................5-88Washing Your Vehicle...................................5-89
Cleaning Exterior Lamps/Lenses.....................5-89
Finish Care..................................................5-89
Windshield, Backglass, and Wiper Blades.........5-90
Aluminum Wheels.........................................5-91
Tires...........................................................5-91
Sheet Metal Damage.....................................5-92
Finish Damage.............................................5-92
Underbody Maintenance................................5-92
Chemical Paint Spotting.................................5-93
Vehicle Care/Appearance Materials..................5-93
Vehicle Identication......................................5-94
Vehicle Identication Number (VIN).................5-94
Service Parts Identication Label.....................5-95
Electrical System............................................5-95
Add-On Electrical Equipment..........................5-95
Windshield Wiper Fuses................................5-95
Power Windows and Other Power Options.......5-96
Fuses and Circuit Breakers............................5-96
Engine Compartment Fuse Block....................5-97
Capacities and Specications........................5-102
Section 5 Service and Appearance Care
5-2

How to Check
Use a good quality pocket-type gage to check tire
pressure. You cannot tell if your tires are properly inated
simply by looking at them. Radial tires may look properly
inated even when they are underinated. Check the
tire’s ination pressure when the tires are cold.
Cold means your vehicle has been sitting for at least
three hours or driven no more than 1 mile (1.6 km).
Remove the valve cap from the tire valve stem. Press
the tire gage rmly onto the valve to get a pressure
measurement. If the cold tire ination pressure matches
the recommended pressure on the Tire and Loading
Information label, no further adjustment is necessary.
If the ination pressure is low, add air until you reach the
recommended amount.
If you overll the tire, release air by pushing on the
metal stem in the center of the tire valve. Recheck the
tire pressure with the tire gage.
Be sure to put the valve caps back on the valve stems.
They help prevent leaks by keeping out dirt and
moisture.
Tire Pressure Monitor System
Your vehicle is equipped with a Tire Pressure Monitor
System (TPMS). This system uses radio and sensor
technology to check tire pressure levels. TPMS sensors
are mounted onto each tire and wheel assembly on
your vehicle, including the spare tire. The TPMS sensors
transmit tire pressure readings to a receiver located in
the vehicle.
Each tire, including the spare (if provided), should be
checked monthly when cold and inated to the ination
pressure recommended by the vehicle manufacturer
on the vehicle placard or tire ination pressure label.
When the low tire pressure
telltale is illuminated, one
or more of your tires is
signicantly under-inated.
You should stop and check your tires as soon as
possible, and inate them to the proper pressure. Driving
on a signicantly under-inated tire causes the tire to
overheat and can lead to tire failure. Under-ination also
reduces fuel efficiency and tire tread life, and may affect
the vehicle’s handling and stopping ability.
5-61

When you have a at tire, you will rst need to set up
the wheel blocks before changing it. They are located in
the tool bag, in the swing-gate. SeeRemoving the
Spare Tire and Tools on page 5-75for more information.
To use the wheel blocks,
lift the wheel block as
shown and lock into place.Then, use the following as a guide to assist you in the
placement of the wheel blocks.
The following information will tell you next how to use
the jack and change a tire.
5-74

Removing the Spare Tire and Tools
The equipment you will need is located in the
swing-gate, behind a cover. To remove the equipment,
do the following:
1. Open the swing-gate. SeeSwing-gate on page 2-9
for more information.
2. Remove the cover by lifting the two latches.
3. Turn the wing nut counterclockwise to release the
jack tool bag and jack.
4. Remove the tool bag and jack from its compartment.5. Undo the straps that secure the jack tool bag to
the jack.
6. Open the tool bag and you will nd the following
tools, which you will use to remove the spare tire
and at tire:
A. Wheel Wrench
B. Jack Handle
ExtensionsC. Jack Handle
D. Jack
E. Wheel Blocks
5-75

The spare tire is attached to the swing-gate. To remove
the spare tire, do the following:
1. Remove the center cap
by placing the at end
of the wheel wrench
in the slot on the wheel
and gently pry the
center cap out.2. Use the wheel wrench
to remove the wheel
nuts securing the
spare tire.
If your vehicle has
locking lug nuts,
the key is supplied
in the tool bag.
Use the key along with
the wheel wrench to
remove the wheel nuts
from the tire.
3. Pull off and gently lower the spare tire to the
ground. Set it next to the at tire.
In order to remove the spare tire, you may need
someone to assist you.
5-76

Removing the Flat Tire and
Installing the Spare Tire
1. Remove the center cap
by placing the at end
of the wheel wrench
in the slot on the wheel
and gently pry the
center cap out.
2. Turn the wheel wrench
counterclockwise to
loosen the wheel nuts.
Do not remove
them yet.If your vehicle has locking lug nuts, the key is
supplied in the tool bag. Use the key along with
the wheel wrench to remove the wheel nuts
from the tire.
You will now need to jack up the vehicle using the
instructions following.
A. Front Position - Lower Control Arm
B. Rear Position - Lower Axle
3. Locate the vehicle’s jacking positions (A and B).
Jacking Locations (Overall View)
5-77

4. Assemble the jack and tools as follows:
Front Tire Flat:If the at tire is on a front tire of
the vehicle, you will need to use the jack handle and
both jack handle extensions. Attach the wheel
wrench to the jack handle extension. Attach the jack
handle to the jack. Position the jack on the front
lower control arm along the bar that runs front
to back. Turn the wheel wrench clockwise to raise
the vehicle. Raise the vehicle far enough off the
ground so there is enough room for the spare tire to
clear the ground.Refer to the graphic above to locate the placement of
the jack if the at tire is on the rear of the vehicle. Front Position
Rear Positions
5-78

Rear Tire Flat:You will need to use the jack
handle and both jack handle extensions. Attach the
wheel wrench to the jack extensions. Attach the
jack handle to the jack. Align the jack under the rear
axle. Turn the wheel wrench clockwise to raise
the vehicle. Raise the vehicle far enough off the
ground so there is enough room for the spare tire to
clear the ground.5. Turn the wheel wrench clockwise to raise the jack
head to the lifting point.
{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack you
could be badly injured or killed. Never get under
a vehicle when it is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.
5-79

6. Remove all the wheel
nuts and take off the
at tire.
{CAUTION:
Rust or dirt on the wheel, or on the parts to
which it is fastened, can make the wheel nuts
become loose after a time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
the places where the wheel attaches to the
vehicle. In an emergency, you can use a cloth
or a paper towel to do this; but be sure to use
a scraper or wire brush later, if needed, to get
all the rust or dirt off.7. Remove any rust or dirt
from the wheel bolts,
mounting surfaces
and spare wheel.
{CAUTION:
Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel
could fall off, causing a serious accident.
8. Put the spare tire on the mounting surface.
9. Put the wheel nuts back on with the rounded end of
the nuts toward the wheel after mounting the spare.
5-80