start stop button HUMMER H3 2007 Owners Manual

The system can only be activated using the
remote keyless entry transmitter, or by OnStar®.
SeeOnStar®System on page 129for additional
information. You should also remember that
you can start your vehicle with the correct key if
the alarm has been set off.
Here is how to avoid setting off the alarm by
accident:
If you do not want to arm the theft-deterrent
system, the vehicle should be locked with
the manual door lock lever, the power
door lock switch, or the key, after the doors
are closed.
If the content theft-deterrent system is armed,
unlock the doors by pressing the unlock
button on the remote keyless entry transmitter
or by OnStar
®. Unlocking a door any other
way will activate the alarm.
If you set off the alarm by accident, you can turn it
off by pressing unlock on the remote keyless
entry transmitter, starting the vehicle with
the correct key, or by having OnStar
®unlock the
doors. The alarm will not stop if you try to
unlock a door any other way.
Testing the Alarm
The alarm can be tested by following these steps:
1. From inside the vehicle, activate the system
by locking the doors with the remote keyless
entry transmitter.
2. Unlock the door with the manual door lock
and open the door. This should set off the
pre-alarm. Wait 10 seconds for the full alarm
to activate.
3. To turn the alarm off, press the unlock button
on the remote keyless entry transmitter or
start the engine.
If the alarm does not sound when it should but the
lights ash, check to see if the horn works. The
horn fuse may be blown. To replace the fuse, see
Fuses and Circuit Breakers on page 417.
If the alarm does not sound or the front turn signal
lamps do not ash, see your dealer for service.
99

Make sure the shift lever is fully in PARK (P)
before starting the engine. Your vehicle has an
automatic transmission shift lock control system.
You must fully apply your regular brakes rst
and then press the shift lever button before you
can shift from PARK (P) when the ignition key is in
ON. If you cannot shift out of PARK (P), ease
pressure on the shift lever and push the shift lever
all the way into PARK (P) as you maintain
brake application. Then press the shift lever button
and move the shift lever into another gear. See
Shifting Out of Park (P) (Automatic Transmission)
on page 119
REVERSE (R):Use this gear to back up.
Notice:Shifting to REVERSE (R) while your
vehicle is moving forward could damage
the transmission. The repairs would not be
covered by your warranty. Shift to
REVERSE (R) only after your vehicle is
stopped.
To rock your vehicle back and forth to get out of
snow, ice, or sand without damaging your
transmission, seeIf Your Vehicle is Stuck in Sand,
Mud, Ice, or Snow on page 286.NEUTRAL (N):In this position, your engine does
not connect with the wheels. To restart when
you are already moving, use NEUTRAL (N) only.
{CAUTION:
Shifting into a drive gear while your
engine is running at high speed is
dangerous. Unless your foot is rmly on
the brake pedal, your vehicle could move
very rapidly. You could lose control and
hit people or objects. Do not shift into a
drive gear while your engine is running at
high speed.
Notice:Shifting out of PARK (P) or
NEUTRAL (N) with the engine running at high
speed may damage the transmission. The
repairs would not be covered by your warranty.
Be sure the engine is not running at high
speed when shifting your vehicle.
107

Press and release the Four-Wheel High or
Four-Wheel-High Lock button. If your vehicle has
a manual transmission, the clutch pedal must
be pressed to the oor while you press the
Four-Wheel High or Four-Wheel-High Lock
button, or the shift will not be completed.
You must wait for the Four-Wheel High or
Four-Wheel-High Lock indicator light to stop
ashing and remain lit before shifting your
transmission into gear.
It is normal for your vehicle to have engagement
noise and bump when shifting between
Four-Wheel Low and Four-Wheel High ranges
or from NEUTRAL with the engine running.
If the Four-Wheel High or Four-Wheel-High Lock
button is pressed when your vehicle is in gear
and/or moving too fast, the Four-Wheel High
or Four-Wheel-High Lock indicator light will ash
for 15 seconds but will not complete the shift
unless your vehicle is moving less than 3 mph
(5 km/h) and the transmission is in NEUTRAL (N).Shifting Into NEUTRAL
To shift the transfer case to NEUTRAL, do the
following:
1. Set the parking brake.
2. Start the vehicle by turning the ignition to
START.
3. Put the transmission in NEUTRAL (N).
If your vehicle has a manual transmission,
press and hold the clutch pedal down
while you perform Steps 5 through 9.
4. Shift the transfer case to Four-Wheel High.
{CAUTION:
Shifting an all-wheel-drive vehicle’s
transfer case into NEUTRAL can cause
your vehicle to roll even if the automatic
transmission is in PARK (P) or the manual
transmission is in any gear. You or others
could be injured. Make sure the parking
brake is rmly set before you shift the
transfer case to NEUTRAL.
114

5. Simultaneously press and hold the Four-Wheel
High and Four-Wheel-Low Lock buttons for
10 seconds. The NEUTRAL light will come on
when the transfer case shift to NEUTRAL is
complete.
6. Press and hold the regular brake pedal and
Shift the transmission to REVERSE (R) for
one second, then shift the transmission for
one second to DRIVE (D) for an automatic
transmission, or FIRST (1) for vehicles have
a manual transmission and then let out the
clutch. This is to ensure the transfer case is
in NEUTRAL. If not, repeat this procedure
starting at Step 3.
7. Turn the engine off, by turning the key to ACC.
8. Place the transmission shift lever in PARK (P)
for an automatic transmission, or FIRST (1)
for vehicles that have a manual transmission.
9. Turn the ignition to LOCK.Shifting Out of NEUTRAL
To shift out of NEUTRAL:
1. Set the parking brake and apply the regular
brake pedal.
2. Shift the transmission to NEUTRAL (N) for an
automatic transmission, or press the clutch
pedal for vehicles that have a manual
transmission. Then turn the ignition to ON
with the engine off.
3. Press the button for the desired transfer
case shift position (Four-Wheel High,
Four-Wheel-High Lock or
Four-Wheel-Low Lock).
After the transfer case has shifted out of
NEUTRAL the light will go out.
4. Release the parking brake.
Notice:Shifting the transmission into gear
before the indicator light stops ashing could
cause damage to the transfer case. Always
wait until the indicator light stops ashing
before putting the transmission back in gear.
5. You may start the engine and shift the
transmission to the desired position.
115

Cleaning the Mirror
When cleaning the mirror, use a paper towel or
similar material dampened with glass cleaner.
Do not spray glass cleaner directly on the mirror
as that may cause the liquid cleaner to enter
the mirror housing.
Automatic Dimming Rearview
Mirror with Compass and
Temperature Display
Your vehicle may have this mirror. When on, an
automatic dimming mirror will dim to the proper
level to minimize glare from lights behind you
after dark.
The mirror also includes a dual display in the
upper right corner of the mirror with the compass
reading and the outside temperature.
Yb:Briey press this button to turn the display
on or off.
Temperature Display
The temperature can be displayed by pressing the
compass/temperature button. Pressing the
compass/temperature button once briey, will
toggle the display reading on and off. To alternate
the temperature reading between Fahrenheit and
Celsius, press and hold the compass/temperature
button for approximately three seconds until the
display blinks F and C. After approximately ve
seconds of inactivity, the display will stop blinking
and display the last selection made.
If an abnormal reading is displayed, see your
dealer.
Automatic Dimming Mirror Operation
O
:Press this button to turn the automatic
dimming feature on or off. The indicator light to
the left of the button will turn on to indicate when
the feature is on. Once the mirror is turned off,
it will remain off until it is turned back on, or until
the vehicle is restarted.
125

Radio Messages for XM™ Only
SeeXM Radio Messages on page 228later in this
section for further detail.
Playing a CD
Insert a CD partway into the slot, label side up. The
player pulls it in and the CD should begin playing.
If you want to insert a CD with the ignition off, rst
press the eject button or the DISP knob.
If the ignition or radio is turned off with a CD in the
player it stays in the player. When the ignition or
radio is turned on, the CD starts to play where it
stopped, if it was the last selected audio source.
When the CD is inserted, the CD symbol appears
on the display. As each new track starts to
play, the track number appears on the display.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs and
the smaller CDs are loaded in the same manner.
If playing a CD-R, the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been handled.There may be an increase in skipping, difficulty
in nding tracks, and/or difficulty in loading and
ejecting. If these problems occur, check the bottom
surface of the CD. If the surface of the CD is
damaged, such as cracked, broken, or scratched,
the CD will not play properly. If the surface of the
CD is soiled, seeCare of Your CDs on page 231
for more information.
If there is no apparent damage, try a known
good CD.
Do not add any label to a CD, it could get caught
in the CD player. If a CD is recorded on a
personal computer and a description label is
needed, try labeling the top of the recorded CD
with a marking pen.
Notice:If you add any label to a CD, insert
more than one CD into the slot at a time, or
attempt to play scratched or damaged CDs,
you could damage the CD player. When using
the CD player, use only CDs in good condition
without any label, load one CD at a time, and
keep the CD player and the loading slot free
of foreign materials, liquids, and debris.
If an error appears on the display, see
“CD Messages” later in this section.
208

tSEEKu:Press the left arrow to go to the
start of the current or the previous track. Press the
right arrow to go to the start of the next track.
Pressing either arrow for more than two seconds
searches the previous or next tracks at
two tracks per second. Release the arrow to
stop searching and to play the track.
1
r(Previous):Press this pushbutton to go
to the start of the current track if more than
eight seconds have played. The previous symbol
and the track number appears on the display.
If this pushbutton is held or pressed more
than once, the player continues moving backward
through the CD.
2
[(Next):Press this pushbutton to go to the
next track. The next symbol and the track number
appears on the display. If this pushbutton is
held or pressed more than once, the player
continues moving forward through the CD.
4
y(Random):Press this pushbutton to hear the
tracks in random, rather than sequential, order. The
random symbol appears on the display. Press this
pushbutton again to turn off random play.BAND:Press this button to listen to the radio
when a CD is playing. The inactive CD remains
safely inside the radio for future listening.
B(CD):Press this button to play a CD while
listening to the radio. The CD symbol appears
on the display when a CD is loaded.
DISP (Display):Press this button to see how
long the current track has been playing. The
elapsed time of the track appears on the display.
To change the default on the display, track or
elapsed time, press this button until you see
the desired display, then hold the button for
two seconds. The radio produces one beep and
the selected display becomes the default.
AUTO EQ (Automatic Equalization):Press EQ
to select an equalization setting while playing
a CD. The equalization is set whenever a CD
is played. See “EQ” listed previously for more
information. If you select an EQ setting for your
CD, it is activated each time you play a CD.
Z(Eject):Press this button to eject a CD.
Eject may be activated with either the ignition or
radio off. CDs can be loaded with the ignition
and radio off if this button is pressed rst.
209

To use repeat, do the following:
To repeat the track you are listening to, press
and release the repeat button. RPT ON
displays. Press this button again to turn off
repeat play. RPT OFF displays.
To repeat the CD you are listening to, press
and hold the repeat button for two seconds.
RPT ON displays. Press this button again
to turn off repeat play. RPT OFF displays.
y(Random):With random, you can listen to the
tracks in random, rather than sequential, order,
on one CD or on all of the CDs. To use random,
do one of the following:
To play the tracks on the CD you are listening
to in random order, press and release the
random button. RANDOM ONE displays.
Press this button again to turn off random play.
To play the tracks on all of the CDs that
are loaded in random order, press and
hold this button for more than two seconds.
A beep sounds and RANDOM ALL displays.
Press this button again to turn off random play.
tSEEKu:Press the left arrow to go to the
start of the current track, if more than ten seconds
have played. Press the right arrow to go to the
next track. If either arrow is held or pressed more
than once, the player continues moving backward
or forward through the CD.
To scan one CD, press and hold either arrow for
more than two seconds until SCAN displays
and a beep sounds. The radio goes to the next
track, plays for 10 seconds, then goes to the next
track. Press either arrow again, to stop scanning.
To scan all loaded CDs, press and hold either arrow
for more than four seconds until CD SCAN displays
and a beep sounds. Use this feature to listen to
10 seconds of the rst track of each loaded CD.
Press either arrow again, to stop scanning.
DISP (Display):Press this knob to see how long
the current track has been playing. The elapsed
time of the track appears on the display. To
change the default on the display, track or elapsed
time, press this knob until you see the desired
display, then hold the knob for two seconds.
The radio produces one beep and the selected
display becomes the default.
219

If the ignition or radio is turned off with a CD in the
player it stays in the player. When the ignition or
radio is turned on, the CD starts to play where it
stopped, if it was the last selected audio source.
As each new track starts to play, the track number
appears on the display.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There may be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check
the bottom surface of the CD. If the surface of
the CD is damaged, such as cracked, broken,
or scratched, the CD will not play properly.
If the surface of the CD is soiled, seeCare of
Your CDs on page 231for more information.
If there is no apparent damage, try a known
good CD.Do not add any label to a CD, it could get caught
in the CD player. If a CD is recorded on a
personal computer and a description label is
needed, try labeling the top of the recorded CD
with a marking pen.
Notice:If you add any label to a CD, insert
more than one CD into the slot at a time, or
attempt to play scratched or damaged CDs,
you could damage the CD player. When using
the CD player, use only CDs in good condition
without any label, load one CD at a time, and
keep the CD player and the loading slot free
of foreign materials, liquids, and debris.
If an error appears on the display, see
“CD Messages” later in this section.
tSEEKu:Press the left arrow to go to the
start of the previous track. Press the right arrow
to go to the start of the next track. Pressing either
arrow for more than two seconds searches the
previous or next tracks at two tracks per second.
Release the button to stop searching and to
play the track.
225