clock HUMMER H3 2008 Owners Manual

Front Seat Storage Net
Your vehicle has storage nets located on the back of
the front seats. To remove these nets, pull out on each
of the four clips located on the net.
Front Armrest Storage Area
Your vehicle has a front armrest storage area. To open,
lift the latch on the front of the armrest and pull up.
Luggage Carrier
If your vehicle has this feature, you can load cargo on
your vehicle.
The luggage carrier consists of siderails attached to
the roof. The crossrails attach into the siderails and
can be moved back and forth to accommodate various
cargo sizes.
Notice:Loading cargo on the luggage carrier
that weighs more than 250 lbs. (113 kg) or hangs
over the rear or sides of the vehicle may damage
your vehicle. Load cargo only on top of the
crossrails and tie the cargo down to the crossrail
support cargo tie-down loops, making sure to
fasten it securelyDo not exceed the maximum vehicle capacity when
loading your vehicle. For more information on vehicle
capacity and loading, seeLoading Your Vehicle
on page 4-42.
Adjusting the Crossrails
To adjust the crossrails to t your load:
1. Use the provided crossrail key to unlock the
crossrail end cap by turning it counterclockwise.
2-57

2. Remove the end cap. 3. Pull the lever labeled “PULL” from left to right to
loosen the crossrail.
4. Repeat Steps 1 through 3 to the opposite end of
the crossrail.
5. Once both sides of the crossrail are loose, adjust
the crossrail to the desired position.
6. Push the lever labeled “PULL” from right to left to
lock the crossrail in place.
7. Reinstall end cap and lock by turning the key
clockwise.
8. Repeat Steps 5 through 7 to the opposite end of
the crossrail.
2-58

Stop Tabs
If your vehicle has a sunroof, it will have a crossrail stop
tab placed in the siderail. This tab prevents you from
moving the crossrails past the opening of the sunroof
and loading cargo too far forward.
Your vehicle may have cargo tie downs. Once you
load the cargo onto the crossrails, secure it by tying it
down to the cargo tie downs. Do not load cargo directly
on the roof of your vehicle. SeeCargo Tie Downs on
page 2-59for more information.
Rear Storage Area
Your vehicle has a rear storage area located on
the passenger’s side of the cargo area. To open,
pull the two tabs out and open lid.
Convenience Net
Your vehicle may have a convenience net in the rear
of the vehicle. Put small loads behind the net. The net
is not for heavier loads. Store them as far forward
as you can.
Cargo Cover
Notice:If you put items onto the cargo cover, the
weight of the items could cause the attachment clips
to break. You would no longer be able to attach
and use the cargo cover. The repairs would not be
covered by your warranty. Never put anything
on top of the cargo cover.
If your vehicle has a cargo cover, you can use it to
cover items in the rear of the vehicle. Remove the
cover from its pouch and place the loops found on
each corner of the cover, over the two pegs in each
corner of the rear if the vehicle. When it is not in
use, fold up the cover and return it to the pouch.
Cargo Tie Downs
Your vehicle may have four cargo tie-downs. These
tie-downs are located in tracks on the roof of the vehicle.
Each tie-down can be moved to anywhere on the
track. To loosen, turn the tie-down counterclockwise
until it moves freely in the track. To tighten, turn
the tie-down clockwise.
2-59

Ashtray(s) and Cigarette Lighter
Your vehicle may have an ashtray and cigarette lighter.
Your ashtray is located in your center console area.
The ashtray can be removed for cleaning. When
the ashtray is removed, this area can also be used as a
cupholder.
Notice:If you put papers, pins, or other ammable
items in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage your vehicle. Never put ammable items in
the ashtray.
To use the lighter, press it in all the way, and let go.
When it’s ready, it will pop back out by itself.
Notice:Holding a cigarette lighter in while it is
heating does not let the lighter back away from the
heating element when it is hot. Damage from
overheating can occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
Climate Controls
Climate Control System
The heating, cooling, and ventilation of the vehicle can
be controlled with this system.
Temperature:Turn the left knob on the control panel to
adjust the temperature of the air in the vehicle. Turn
the knob clockwise or counterclockwise to increase or
decrease the temperature.
#(Air Conditioning):Press the center of the left
knob on the control panel to turn the air conditioning
system on or off. An indicator light on the button will be
lit when the air conditioning is turned on. This system
cools and dehumidies the air entering the vehicle.
3-22

The air conditioning will not function if the fan is turned
off. If air conditioning is selected with fan off, the
indicator light ashes three times and then turns off.
A slight change in engine performance may occur when
the air conditioning compressor shuts off and turns
on again. This is normal. The system is designed
to make adjustments to help with fuel economy while
still maintaining the selected temperature.
The air conditioning system removes moisture from the
air, so sometimes there may be a small amount of
water dripping underneath the vehicle while idling or
after turning off the engine. This is normal.
9(Fan):Turn the center knob on the control panel to
control the fan speed. Turn the knob clockwise or
counterclockwise to increase or decrease the fan speed.
9(Off):Turn the center knob to this position to turn
the fan off. With the fan off, you may still experience
airow from the system that increases with vehicle
speed depending on the mode and temperature settings.
Enable recirculation mode to stop this airow from
occurring.
@(Recirculation):Press the center of the fan
control knob to recirculate air inside the vehicle and
prevent outside air from coming in. It can be used
to prevent outside odors from entering the vehicle and
cool the air inside the vehicle more quickly. Pressthis button to turn the recirculation mode on or off. An
indicator light on the button comes on to show that
the recirculation mode is activated.
Recirculation is available in the bi-level, and vent
modes. Recirculation is not available while in oor,
oor/defog and defrost mode. If recirculation is selected
in these modes, the indicator ashes three times
indicating it is not available in that mode. When the
recirculation mode is turned on, the air conditioning turns
on automatically.
When it is hot enough outside, the recirculation mode
may turn on automatically to help improve cooling
performance. The indicator light will be lit to show this
mode is active. If the recirculation button is pressed
while in this mode, the light will ash three times
and stay on to indicate that recirculation may not be
shut off.
The right knob on the control panel is used to direct the
airow inside the vehicle. In-between modes are
available by moving the right control knob between
modes with symbols. The in-between mode is a
combination of the two modes that the control is
centered between.
Turn the right knob to select one of the following modes:
H(Vent):This mode directs air to the instrument
panel outlets.
3-23

Playing the Radio
P
(Power/Volume):Press to turn the system on
and off.
Turn clockwise or counterclockwise to increase or to
decrease the volume.
DISP (Display):Press to switch the display between
the radio station frequency and the time. When the
ignition is turned off, press to display the time.
For XM™ (if equipped), press the DISP button while in
XM™ mode to retrieve four different categories of
information related to the current song or channel: Artist,
Song Title, Category or PTY (program type), Channel
Number/Channel Name.
To change the default on the display, press the DISP
button until you see the desired display, then hold
this knob for two seconds. The radio produces one beep
and the selected display becomes the default.
AUTO VOL (Automatic Volume):With automatic
volume, the audio system adjusts automatically to make
up for road and wind noise as you drive.
Set the volume at the desired level. Press to select
LOW, MEDIUM, or HIGH. Each higher setting allows for
more volume compensation at faster vehicle speeds.
Then as you drive, automatic volume increases
the volume, as necessary, to overcome noise at anyspeed. The volume level should always sound the same
to you as you drive. NONE displays if the radio cannot
determine the vehicle speed. To turn automatic
volume off, press until AVOL OFF displays.
Finding a Station
BAND:Press to switch between FM1, FM2, AM, or
XM1 or XM2 (if equipped). The selection displays.
e(Tune):Turn to select radio stations.
tSEEKu:Press and release the arrows to go to
the next or to the previous station and stay there.
To scan stations, press and hold either arrow for more
than two seconds. SCN or SCAN displays and the
radio produces one beep. The radio goes to a station,
plays for a few seconds, then goes to the next
station. Press either arrow again or one of the
pushbuttons to stop scanning presets.
To scan preset stations, press and hold either arrow for
more than four seconds. PSC or PSCN displays and
the radio produces two beeps. The radio goes to
a preset station, plays for a few seconds, then goes to
the next preset station. Press either arrow again or
one of the pushbuttons to stop scanning presets.
The radio only seeks and scans stations with a strong
signal that are in the selected band.
3-50

Speed limit signs near curves warn that you should
adjust your speed. Of course, the posted speeds
are based on good weather and road conditions. Under
less favorable conditions you will want to go slower.
If you need to reduce your speed as you approach
a curve, do it before you enter the curve, while the
front wheels are straight ahead.
Try to adjust your speed so you can drive through
the curve. Maintain a reasonable, steady speed.
Wait to accelerate until you are out of the curve,
and then accelerate gently into the straightaway.
Adding non-dealer/non-retailer accessories can affect
your vehicle’s performance. SeeAccessories and
Modifications on page 5-3.
Steering in Emergencies
There are times when steering can be more effective than
braking. For example, you come over a hill and nd a
truck stopped in your lane, or a car suddenly pulls out
from nowhere, or a child darts out from between parked
cars and stops right in front of you. You can avoid these
problems by braking — if you can stop in time. But
sometimes you cannot; there is not room. That is the time
for evasive action — steering around the problem.
Your vehicle can perform very well in emergencies like
these. First apply the brakes. SeeBraking on page 4-3.
It is better to remove as much speed as you can from a
possible collision. Then steer around the problem, to the
left or right depending on the space available.An emergency like this requires close attention and a
quick decision. If you are holding the steering wheel
at the recommended 9 and 3 o’clock positions, you can
turn it a full 180 degrees very quickly without removing
either hand. But you have to act fast, steer quickly, and
just as quickly straighten the wheel once you have
avoided the object.
The fact that such emergency situations are always
possible is a good reason to practice defensive driving
at all times and wear safety belts properly.
4-9

Sound the horn as you approach the top of the
hill to let opposing traffic know you are there.
Use your headlamps even during the day.
They make your vehicle more visible to
oncoming traffic.
{CAUTION:
Driving to the top (crest) of a hill at full speed
can cause an accident. There could be a
drop-off, embankment, cliff, or even another
vehicle. You could be seriously injured or
killed. As you near the top of a hill, slow down
and stay alert.There are some things you should do if the vehicle stalls,
or is about to stall, and you cannot make it up the hill:
Push the brake pedal to stop the vehicle and keep
it from rolling backwards. Also, apply the parking
brake.
If your engine is still running, shift the transmission to
REVERSE (R), release the parking brake, and slowly
back down the hill in REVERSE (R).
If your engine has stopped running, you will need
to restart it. With the brake pedal pressed, apply
the parking brake. If you have an automatic
transmission, shift the transmission to PARK (P).
Restart the engine. Then, shift to REVERSE (R),
release the parking brake, and slowly back down
the hill as straight as possible in REVERSE (R).
As you are backing down the hill, put your left hand
on the steering wheel at the 12 o’clock position.
This way, you will be able to tell if your wheels are
straight and maneuver as you back down. It is best
that you back down the hill with your wheels straight
rather than in the left or right direction. Turning the
wheel too far to the left or right will increase the
possibility of a rollover.
4-24

To remove the fuel cap, turn it slowly counterclockwise.
While refueling, let the fuel cap hang by the tether, if
it has one.
{CAUTION:
Fuel can spray out on you if you open the fuel
cap too quickly. If you spill fuel and then
something ignites it, you could be badly
burned. This spray can happen if your tank is
nearly full, and is more likely in hot weather.
Open the fuel cap slowly and wait for any hiss
noise to stop. Then unscrew the cap all the
way.
Be careful not to spill fuel. Do not top off or overll the
tank and wait a few seconds after you have nished
pumping before removing the nozzle. Clean fuel
from painted surfaces as soon as possible. See
Washing Your Vehicle on page 5-95.
When replacing the fuel cap, turn it clockwise until it
clicks. Make sure the cap is fully installed. The diagnostic
system can determine if the fuel cap has been left off or
improperly installed. This would allow fuel to evaporate
into the atmosphere. SeeMalfunction Indicator Lamp on
page 3-36.The FUEL CAP message will be displayed on the Driver
Information Center (DIC) if the fuel cap is not properly
installed. SeeDIC Warnings and Messages on
page 3-43for more information.
{CAUTION:
If a re starts while you are refueling, do not
remove the nozzle. Shut off the ow of fuel by
shutting off the pump or by notifying the
station attendant. Leave the area immediately.
Notice:If you need a new fuel cap, be sure to get
the right type. Your dealer/retailer can get one
for you. If you get the wrong type, it may not t
properly. This may cause your malfunction indicator
lamp to light and may damage your fuel tank and
emissions system. SeeMalfunction Indicator Lamp
on page 3-36.
5-9

If the overheat warning continues, there is one more
thing you can try. Add the proper mixture directly to the
radiator, but be sure the cooling system is cool before
you do it.
{CAUTION:
Steam and scalding liquids from a hot cooling
system can blow out and burn you badly. They
are under pressure, and if you turn the radiator
pressure cap — even a little — they can come
out at high speed. Never turn the cap when the
cooling system, including the radiator pressure
cap, is hot. Wait for the cooling system and
radiator pressure cap to cool if you ever have
to turn the pressure cap.
How to Add Coolant to the Radiator
1. Remove the radiator pressure cap when the cooling
system, including the upper radiator hose, is no
longer hot. Turn the pressure cap slowly
counterclockwise about one full turn.
If you hear a hiss, wait for that to stop. A hiss
means there is still some pressure left.
2. Keep turning the cap to remove it.
3. Fill the radiator with the proper DEX-COOL
®
coolant mixture, up to the base of the ller
neck. SeeEngine Coolant on page 5-27for more
information about the proper coolant mixture.
5-34