clock setting HUMMER H3 2008 Owners Manual

The air conditioning will not function if the fan is turned
off. If air conditioning is selected with fan off, the
indicator light ashes three times and then turns off.
A slight change in engine performance may occur when
the air conditioning compressor shuts off and turns
on again. This is normal. The system is designed
to make adjustments to help with fuel economy while
still maintaining the selected temperature.
The air conditioning system removes moisture from the
air, so sometimes there may be a small amount of
water dripping underneath the vehicle while idling or
after turning off the engine. This is normal.
9(Fan):Turn the center knob on the control panel to
control the fan speed. Turn the knob clockwise or
counterclockwise to increase or decrease the fan speed.
9(Off):Turn the center knob to this position to turn
the fan off. With the fan off, you may still experience
airow from the system that increases with vehicle
speed depending on the mode and temperature settings.
Enable recirculation mode to stop this airow from
occurring.
@(Recirculation):Press the center of the fan
control knob to recirculate air inside the vehicle and
prevent outside air from coming in. It can be used
to prevent outside odors from entering the vehicle and
cool the air inside the vehicle more quickly. Pressthis button to turn the recirculation mode on or off. An
indicator light on the button comes on to show that
the recirculation mode is activated.
Recirculation is available in the bi-level, and vent
modes. Recirculation is not available while in oor,
oor/defog and defrost mode. If recirculation is selected
in these modes, the indicator ashes three times
indicating it is not available in that mode. When the
recirculation mode is turned on, the air conditioning turns
on automatically.
When it is hot enough outside, the recirculation mode
may turn on automatically to help improve cooling
performance. The indicator light will be lit to show this
mode is active. If the recirculation button is pressed
while in this mode, the light will ash three times
and stay on to indicate that recirculation may not be
shut off.
The right knob on the control panel is used to direct the
airow inside the vehicle. In-between modes are
available by moving the right control knob between
modes with symbols. The in-between mode is a
combination of the two modes that the control is
centered between.
Turn the right knob to select one of the following modes:
H(Vent):This mode directs air to the instrument
panel outlets.
3-23

Playing the Radio
P
(Power/Volume):Press to turn the system on
and off.
Turn clockwise or counterclockwise to increase or to
decrease the volume.
DISP (Display):Press to switch the display between
the radio station frequency and the time. When the
ignition is turned off, press to display the time.
For XM™ (if equipped), press the DISP button while in
XM™ mode to retrieve four different categories of
information related to the current song or channel: Artist,
Song Title, Category or PTY (program type), Channel
Number/Channel Name.
To change the default on the display, press the DISP
button until you see the desired display, then hold
this knob for two seconds. The radio produces one beep
and the selected display becomes the default.
AUTO VOL (Automatic Volume):With automatic
volume, the audio system adjusts automatically to make
up for road and wind noise as you drive.
Set the volume at the desired level. Press to select
LOW, MEDIUM, or HIGH. Each higher setting allows for
more volume compensation at faster vehicle speeds.
Then as you drive, automatic volume increases
the volume, as necessary, to overcome noise at anyspeed. The volume level should always sound the same
to you as you drive. NONE displays if the radio cannot
determine the vehicle speed. To turn automatic
volume off, press until AVOL OFF displays.
Finding a Station
BAND:Press to switch between FM1, FM2, AM, or
XM1 or XM2 (if equipped). The selection displays.
e(Tune):Turn to select radio stations.
tSEEKu:Press and release the arrows to go to
the next or to the previous station and stay there.
To scan stations, press and hold either arrow for more
than two seconds. SCN or SCAN displays and the
radio produces one beep. The radio goes to a station,
plays for a few seconds, then goes to the next
station. Press either arrow again or one of the
pushbuttons to stop scanning presets.
To scan preset stations, press and hold either arrow for
more than four seconds. PSC or PSCN displays and
the radio produces two beeps. The radio goes to
a preset station, plays for a few seconds, then goes to
the next preset station. Press either arrow again or
one of the pushbuttons to stop scanning presets.
The radio only seeks and scans stations with a strong
signal that are in the selected band.
3-50