ignition HUMMER H3 2009 Owner's Guide

If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system. See
your dealer/retailer for service.
{CAUTION
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 3-25for more information,
including important safety
information.
Charging System Light
This light comes on briey when the
ignition key is turned, but the
engine is not running, as a check to
show it is working.
It should go out once the engine
starts. If it stays on, or comes
on while driving, there could be a
problem with the charging system. A
charging system message in the
Driver Information Center (DIC) may
also appear. SeeDIC Warnings
and Messages on page 3-37
for more information. This light could
indicate that there are problems
with a generator drive belt, or that
there is an electrical problem.
Have it checked right away. If the
vehicle must be driven a short
distance with the light on, turn off all
the accessories, such as the
radio and air conditioner.
Up-Shift Light
The vehicle may have an up-shift
light.
When this light comes on, shift to
the next higher gear if weather,
road, and traffic conditions allow.
SeeManual Transmission Operation
on page 2-22for more information.
Brake System Warning
Light
The vehicle’s hydraulic brake
system is divided into two parts. If
one part is not working, the
other part can still work and stop
the vehicle. For good braking
though, both parts need to be
working well.
Instrument Panel 3-27

If the warning light comes on, there
could be a brake problem. Have
the brake system inspected
right away.
This light comes on briey when the
ignition key is turned to ON/RUN.
If it does not, have it xed so it
will be ready to warn if there is a
problem.
When the ignition is on, the brake
system warning light comes on
when the parking brake is set. See
Parking Brake on page 2-28for
more information. The light stays on
if the parking brake does not
release fully. If it stays on after the
parking brake is fully released, it
means there is a brake problem.If the light comes on while driving,
pull off the road and stop. The brake
pedal might be harder to push, or
it might go closer to the oor. It can
take longer to stop. If the light is
still on, have the vehicle towed for
service. SeeTowing Your Vehicle
on page 4-40.
{CAUTION
The brake system might not be
working properly if the brake
system warning light is on. Driving
with the brake system warning
light on can lead to a crash. If the
light is still on after the vehicle
has been pulled off the road and
carefully stopped, have the
vehicle towed for service.
Antilock Brake System
(ABS) Warning Light
For vehicles with the Antilock Brake
System (ABS), this light comes
on briey when the engine is started.
If it does not, have the vehicle
serviced by your dealer/retailer. If
the system is working normally
the indicator light will then go off.
If the ABS light stays on, turn
the ignition off. If the light comes on
while driving, stop as soon as it
is safely possible and turn the
ignition off. Then start the engine
again to reset the system. If the ABS
light stays on, or comes on again
while driving, the vehicle needs
service. If the regular brake system
warning light is not on, the vehicle
still has brakes, but not antilock
brakes. If the regular brake system
warning light is also on, the
vehicle does not have antilock United States
Canada
3-28 Instrument Panel

Tire Pressure Light
The tire pressure light should come
on briey as the engine is started.
If it does not, have the vehicle
service by your dealer/retailer. It
provides information about tire
pressures and the Tire Pressure
Monitoring System.
When the Light is On Steady
This indicates that one or more of
the tires are signicantly
underinated.
A tire pressure message in the
Driver Information Center (DIC),
may accompany the light. SeeDIC
Warnings and Messages on
page 3-37for more information.
Stop and check the tires as soon as
it is safe to do so. If underinated,
inate to the proper pressure.
SeeTires on page 5-44for more
information.When the Light Flashes First and
Then is On Steady
This indicates that there may be a
problem with the Tire Pressure
Monitor System. The light ashes
for about a minute and stays
on steady for the remainder of the
ignition cycle. This sequence
will repeat with every ignition cycle.
SeeTire Pressure Monitor System
on page 5-52for more information.
Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It ensures
that emissions are at acceptable
levels for the life of the vehicle,
helping to produce a cleaner
environment.This light comes on when the
ignition is on, but the engine is not
running, as a check to show it
is working. If it does not, have the
vehicle serviced by your
dealer/retailer.
If the check engine light comes on
and stays on, while the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem
is apparent. Being aware of the light
can prevent more serious damage
to the vehicle. This system
assists the service technician in
correctly diagnosing any
malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
3-30 Instrument Panel

Notice:Lack of proper engine oil
maintenance can damage the
engine. The repairs would not be
covered by the vehicle warranty.
Always follow the maintenance
schedule in this manual for
changing engine oil.
The oil pressure light should come
on briey as the engine is started.
If it does not come on have the
vehicle serviced by your
dealer/retailer.
If the light comes on and stays on, it
means that oil is not owing
through the engine properly. The
vehicle could be low on oil and
might have some other system
problem.Security Light
For information regarding this light
and the vehicle’s security system,
seeContent Theft-Deterrent
on page 2-11.
Cruise Control Light
This light comes on whenever the
cruise control is set.
The light goes out when the cruise
control is turned off. SeeCruise
Control on page 3-9for more
information.
Highbeam On Light
This light comes on when the
high-beam headlamps are in use.
SeeHeadlamp High/Low-Beam
Changer on page 3-7for more
information.
Fuel Gage
The fuel gage indicates about how
much fuel there is remaining in
the fuel tank. The ignition must be
in ON/RUN.
United StatesCanada
Instrument Panel 3-33

An arrow on the fuel gage indicates
the side of the vehicle the fuel
door is on.
Here are three things that can
happen but do not indicate a
problem with the fuel gage:
At the gas station, the gas pump
shuts off before the gage
reads full.
It takes a little more or less fuel
to ll up than the gage indicated.
For example, the gage may
have indicated the tank was half
full, but it actually took a little
more or less than half the tank’s
capacity to ll the tank.
The gage moves a little when
turning a corner or speeding up.
When the fuel in the fuel tank is low,
a LOW FUEL message displays
on the Driver Information
Center (DIC). SeeDIC Warnings
and Messages on page 3-37
for more information.
Driver Information
Center (DIC)
The Driver Information Center (DIC)
displays information such as the
trip odometer, personalization
features, and warning messages.
The DIC display is located on
the instrument panel cluster.
DIC Operation and
Displays
The Driver Information Center (DIC)
comes on when the ignition is on.
If a problem is detected, a warning
message appears on the display.
Pressing and releasing the trip
odometer reset stem on the
DIC acknowledges some current
warnings or service messages.
Some messages only clear after the
required action has been taken.
The DIC has different modes which
can be accessed by pressing the
trip odometer reset stem on the DIC.
These modes are explained in thefollowing section. The DIC trip
odometer reset stem is located on
the instrument panel cluster
next to the DIC display. To scroll
through the available functions,
press and release the reset stem.
Trip Information
Odometer
The odometer is automatically
displayed on the DIC when you start
the vehicle. The odometer shows the
total distance the vehicle has been
driven in either miles for the United
States or kilometers for Canada.
Trip Odometer
Press and release the reset stem
until TRIP appears on the DIC
display. The trip odometer shows the
current distance traveled since the
last reset of the trip odometer in
either miles for the United States or
kilometers for Canada.
To reset the trip odometer, press
and hold the reset stem until
the display returns to zero.
3-34 Instrument Panel

Engine Oil Life System
With the engine off, turn the key to
ON/RUN and then press the
reset stem until OIL LIFE RESET
appears — alternating between OIL
LIFE and RESET — on the DIC
display. The CHANGE OIL message
alerts you to change the oil on a
schedule consistent with your driving
conditions. Always reset the OIL
LIFE message after an oil change.
To reset the message, see
Engine Oil Life System on
page 5-15.
In addition to the engine oil life
system monitoring the oil life,
additional maintenance is
recommended in the Maintenance
Schedule in this manual. See
Engine Oil on page 5-13and
Scheduled Maintenance on page 6-4
for more information.
Language
This feature allows you to choose
the language in which the DIC
display shows information.To set your choice for this feature:
1. With the engine off, turn the
key to ON/RUN, but do not
start the engine.
2. Close all doors so the DOORS
message does not display in
the DIC.
3. Momentarily press and release
the reset stem until the current
language is displayed: English
(default), Spanish, or French.
4. To select a different language,
press and hold the reset stem
until the next language appears.
5. Repeat Step 4 until the desired
language is displayed. Once the
desired language is shown on
the DIC display, the language
is set.
6. To exit the language selection,
momentarily press and release
the reset stem. All DIC messages
will now display in the language
selected.
Automatic Door Locks
This feature allows you to program
the door locks to a preferred
setting.
To set your choice for this feature:
1. With the engine off, turn the
key to LOCK/OFF. Do not
remove the key from the ignition.
2. Press and hold the power
door lock button until the
DIC display shows the current
door lock mode.
3. To view the next available mode,
press and hold the reset stem
until the mode appears. Release
the reset stem and press and
hold again to view the next mode.
4. Once the desired mode is shown
on the DIC display, briey press
the reset stem to set your
choice. The DIC display then
clears.
Instrument Panel 3-35

The following are the available
modes:
Lock 1 (default):On vehicles with
an automatic transmission, this
mode locks all of the doors when
the vehicle is shifted out of P (Park)
and unlocks all of the doors when
the vehicle is shifted into P (Park).
On vehicles with a manual
transmission, this mode locks all of
the doors when the vehicle speed is
greater than 15 mph (24 km/h) and
unlocks all of the doors when the key
is removed from the ignition.
Lock 2:On vehicles with an
automatic transmission, this mode
locks all of the doors when the
vehicle is shifted out of P (Park) and
unlocks the driver’s door when
the vehicle is shifted into P (Park).
On vehicles with a manual
transmission, this mode locks all of
the doors when the vehicle speed is
greater than 15 mph (24 km/h) and
unlocks the driver’s door when the
key is removed from the ignition.Lock 3:On vehicles with an
automatic transmission, this mode
locks all of the doors when the
vehicle is shifted out of P (Park).
The doors will not automatically
unlock.
On vehicles with a manual
transmission, this mode locks all of
the doors when the vehicle
speed is greater than 15 mph
(24 km/h). The doors will not
automatically unlock.
Remote Keyless Entry (RKE)
Feedback
This feature allows you to program
the Remote Keyless Entry (RKE)
feedback to a preferred setting.
To set your choice for this feature:
1. With the engine off, turn the
key to LOCK/OFF. Do not
remove the key from the ignition.
2. Press and hold the lock and
unlock buttons on the RKE
transmitter at the same time.Hold both buttons until the DIC
display shows the current
RKE feedback mode.
3. To view the next available mode,
press and hold the reset stem
until the mode appears. Release
the reset stem and press and
hold again to view the next mode.
4. Once the desired mode is shown
on the DIC display, briey press
the reset stem to set your choice.
The DIC display then clears.
The following are the available
modes:
RFA 1 (default):This mode ashes
the parking lamps when you
press the lock or unlock buttons on
the RKE transmitter.
RFA 2:This mode ashes the
parking lamps and sounds the horn
when you press the lock button
on the RKE transmitter. This mode
also ashes the parking lamps
when you press the unlock button
on the RKE transmitter.
3-36 Instrument Panel

message and clear it from the
display. The message appears at
each ignition cycle until the tires are
inated to the correct ination
pressure. SeeTires on page 5-44
andInflation - Tire Pressure on
page 5-51for more information on
tires and the correct ination
pressures.
OIL
This message displays when the oil
pressure is low. SeeOil Pressure
Light on page 3-32andEngine
Oil on page 5-13for more
information.
PARK BRK (Brake)
This message displays when the
parking brake is set. SeeParking
Brake on page 2-28andBrake
System Warning Light on page 3-27
for more information. The message
clears from the display after the
parking brake is released or by
pressing and releasing the
reset stem.
REDUCED POWER
This message displays when the
vehicle’s engine power is reduced.
Reduced engine power can
affect the vehicle’s ability to
accelerate. If this message is on,
but there is no reduction in
performance, proceed to your
destination. The performance may
be reduced the next time the vehicle
is driven. The vehicle may be
driven at a reduced speed while this
message is on, but acceleration
and speed may be reduced. Anytime
this message stays on, the vehicle
should be taken to your
dealer/retailer for service as soon as
possible. Press and release the
reset stem to acknowledge
the message and clear it from the
display.
SERV (Service) 4WD
(Four-Wheel Drive)
This message displays when there
is a problem with the transfer
case control system. Check the
transfer case on the vehicleand have it serviced by your
dealer/retailer. SeeFull-Time
Four-Wheel Drive on page 2-24for
more information about the
transfer case. Press and release the
reset stem to acknowledge the
message and clear it from the
display.
SERV (Service) TPM
(Tire Pressure Monitor)
On vehicles with the Tire Pressure
Monitor System (TPMS), this
message displays if a part on the
TPMS is not working properly.
The tire pressure light also ashes
and then remains on during the
same ignition cycle. SeeTire
Pressure Light on page 3-30.
Several conditions may cause this
message to appear. SeeTire
Pressure Monitor Operation on
page 5-54for more information. If
the warning comes on and stays on,
there may be a problem with the
TPMS. See your dealer/retailer.
Instrument Panel 3-39

Audio System(s)
Determine which radio the vehicle
has and read the following pages to
become familiar with its features.
{CAUTION
Taking your eyes off the road for
extended periods could cause a
crash resulting in injury or death
to you or others. Do not give
extended attention to
entertainment tasks while driving.
This system provides access to
many audio and non audio listings.
To minimize taking your eyes off
the road while driving, do the
following while the vehicle is parked:
Become familiar with the
operation and controls of
the audio system.
Set up the tone, speaker
adjustments, and preset radio
stations.For more information, seeDefensive
Driving on page 4-2.
Notice:Contact your
dealer/retailer before adding any
equipment.
Adding audio or communication
equipment could interfere
with the operation of the vehicle’s
engine, radio, or other systems,
and could damage them.
Follow federal rules covering
mobile radio and telephone
equipment.
The vehicle has Retained Accessory
Power (RAP). With RAP, the
audio system can be played even
after the ignition is turned off.
SeeRetained Accessory Power
(RAP) on page 2-17for more
information.
Setting the Clock
The clock can be set with the
ignition on or off.
To set the clock:
1. Press and hold H until the
correct hour and AM or PM
displays.
2. Press and hold M until the
correct minute displays.
Press DISP (Display) to display the
time while the ignition is turned off.
Instrument Panel 3-41

The vehicle has one of these radios
as its audio system.
Playing the Radio
P(Power/Volume):Press to turn
the system on and off.
Turn to increase or to decrease the
volume. DISP (Display):
Press to:
Display the time when the
ignition is off.
Switch the display between the
station frequency and the time.
Retrieve four different categories
of information while in XM™
mode related to the current song or channel: Artist, Song Title,
Category or PTY (program type),
Channel Number/Channel Name.
To change the default display:
1. Press DISP until the desired display is shown.
2. Press and hold DISP for two seconds and the radio
produces one beep. The selected
display becomes the default.
Audio Settings
AUTO EQ (Automatic
Equalization): Press and release to
select customized equalization
settings designed for country/
western, jazz, talk, pop, rock, and
classical. To return the bass and
treble to the manual mode, press and
release
euntil MANUAL displays.
AUTO VOL (Automatic Volume):
This adjusts the radio volume to
compensate for road and wind
noise.
Six-Disc CD Radio
Instrument Panel 3-43