start stop button HUMMER H3 2009 Owners Manual

The ignition must be on for the
heated seat feature to work. The
seat will heat to the last setting if the
ignition has been turned off and then
turned back on.
For the heated seat feature to work
on the passenger seat the safety
belt must be fastened.
If the controls are located on the
center console, press the button to
turn the heated seat and seatback
on or off.
Each time the button is pressed, the
temperature settings change from
high, to low, to off. Indicator lights
on the button show the level of
heat selected: two for high, and
one for low.Reclining Seatbacks
{CAUTION
You can lose control of the
vehicle if you try to adjust a
manual driver’s seat while the
vehicle is moving. The sudden
movement could startle and
confuse you, or make you push a
pedal when you do not want to.
Adjust the driver’s seat only when
the vehicle is not moving.
{CAUTION
If either seatback is not locked, it
could move forward in a sudden
stop or crash. That could cause
injury to the person sitting there.
Always push and pull on the
seatbacks to be sure they are
locked.The seats have manual reclining
seatbacks. The lever used to
operate them is located on the
outboard side of the seats.
To recline the seatback:
1. Lift the recline lever and move the
seatback to the desired position,
then release the lever to lock the
seatback in place.
2. Push and pull on the seatback to
make sure it is locked.
Seats and Restraint System 1-5

To avoid setting off the alarm by
accident:
Lock the vehicle with the manual
door lock lever, the power door
lock switch, or the key, after
the doors are closed.
Unlock the doors by pressing the
unlock button on the RKE
transmitter or by contacting
OnStar. Unlocking a door any
other way activates the alarm.
Press unlock on the RKE
transmitter, start the vehicle with
the correct key, or have OnStar
unlock the doors to turn the alarm
off. The alarm does not stop if
a door is unlocked any other way.
Testing the Alarm
To test the alarm:
1. From inside the vehicle, lock the
doors with the RKE transmitter.
2. Unlock the door with the manual
door lock and open the door.
The pre-alarm should sound
followed by the full alarm about
10 seconds later.
3. Press the unlock button on the
RKE transmitter or start the
engine to turn the alarm off.
If the alarm does not sound but the
lights ash, check to see if the
horn works. The horn fuse could be
blown. To replace the fuse, see
Fuses and Circuit Breakers
on page 5-91.
If the alarm does not sound or
the front turn signal lamps do not
ash, see your dealer/retailer
for service.
Passlock®(U.S. Only)
Passlock®is a passive
theft-deterrent system that enables
fuel if the vehicle is started with
a valid key. If an incorrect key
is used or the ignition lock cylinder
is tampered with, the fuel system
is disabled and the vehicle does
not start.
The security light turns off
approximately ve seconds after
the engine is started. SeeSecurity
Light on page 3-33.
If the engine stalls and the security
light ashes, wait about 10 minutes
until the light stops ashing
before trying to restart the engine.
Release the key from START
as soon as the engine starts.
If the engine does not start after
three tries, the vehicle needs
service.
2-12 Features and Controls

It features an electronic shift
position indicator within the
instrument cluster.
There are several different positions
for the shift lever.
P (Park):This position locks the
rear wheels. It is the best position
to use when you start the engine
because the vehicle cannot
move easily.
{CAUTION
It is dangerous to get out of the
vehicle if the shift lever is not fully
in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the
engine is running unless you have
to. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, always set the
parking brake and move the shift
lever to P (Park). SeeShifting Into
Park (Automatic Transmission) on
page 2-29. If you are pulling a
trailer, seeTowing a Trailer on
page 4-42.
Make sure the shift lever is fully in
P (Park) before starting the engine.
The vehicle has an automatic
transmission shift lock controlsystem. You must fully apply the
regular brakes rst and then press
the shift lever button before you
can shift from P (Park) when
the ignition key is in ON/RUN. If you
cannot shift out of P (Park), ease
pressure on the shift lever and push
the shift lever all the way into
P (Park) as you maintain brake
application. Then press the
shift lever button and move the shift
lever into another gear. See
Shifting Out of Park (Automatic
Transmission) on page 2-30
R (Reverse):Use this gear to
back up.
Notice:Shifting to R (Reverse)
while the vehicle is moving
forward could damage the
transmission. The repairs would
not be covered by the vehicle
warranty. Shift to R (Reverse)
only after the vehicle is stopped.
2-20 Features and Controls

Shifting Out of
Four-Wheel-Low Lock
Notice:Shifting the transmission
into gear before the indicator
light stops ashing could cause
damage to the transfer case.
Always wait until the indicator
light stops ashing before putting
the transmission back in gear.
To shift out of Four-Wheel-Low Lock,
the vehicle must be stopped or
moving less than 3 mph (5 km/h)
with the transmission in N (Neutral)
and the ignition in ON/RUN.
The preferred method for shifting out
of Four-Wheel-Low Lock is to have
the vehicle moving 1 to 2 mph
(1.6 to 3.2 km/h). Press and
release the Four-Wheel High or
Four-Wheel-High Lock button.If the vehicle has a manual
transmission, the clutch pedal must
be pressed to the oor while you
press the Four-Wheel High or
Four-Wheel-High Lock button, or the
shift will not be completed. You must
wait for the Four-Wheel High or
Four-Wheel-High Lock indicator light
to stop ashing and remain lit before
shifting the transmission into gear.
It is normal for the vehicle to have
engagement noise and bump
when shifting between Four-Wheel
Low and Four-Wheel High ranges
or from Neutral.
If the Four-Wheel High or
Four-Wheel-High Lock button is
pressed when the vehicle is in
gear and/or moving too fast,
the Four-Wheel High or
Four-Wheel-High Lock indicator
light will ash for 15 seconds but
will not complete the shift.Shifting Into Neutral
To shift the transfer case to Neutral:
1. Set the parking brake.
2. Start the vehicle.
3. Put the transmission in
N (Neutral). If the vehicle has a
manual transmission, press and
hold the clutch pedal down while
you perform Steps 5 through 9.
4. Shift the transfer case to
Four-Wheel High.
{CAUTION
Shifting an all-wheel-drive
vehicle’s transfer case into
Neutral can cause the vehicle
to roll even if the automatic
transmission is in P (Park) or the
manual transmission is in any
gear. You or others could be
injured. Make sure the parking
brake is rmly set before you shift
the transfer case to Neutral.
2-26 Features and Controls

5. Simultaneously press and hold
the Four-Wheel High and
Four-Wheel-Low Lock buttons for
10 seconds. The Neutral light
will come on when the transfer
case shift to Neutral is complete.
6. Press and hold the regular brake
pedal and shift the transmission
to R (Reverse), then shift the
transmission to D (Drive) for an
automatic transmission, or
1 (First) for vehicles have a
manual transmission and then let
out the clutch. This is to ensure
the transfer case is in Neutral.
If not, repeat this procedure
starting at Step 3.
7. Turn the engine off.
8. Place the transmission shift lever
in P (Park) for an automatic
transmission, or 1 (First) for
vehicles that have a manual
transmission.
9. Turn the ignition to LOCK/OFF.Shifting Out of Neutral
To shift out of Neutral:
1. Set the parking brake and apply
the regular brake pedal.
2. Shift the transmission to
N (Neutral) for an automatic
transmission, or press the clutch
pedal for vehicles that have a
manual transmission. Then turn
the ignition to ON/RUN but
do not start the engine.
3. Press the button for the desired
transfer case shift position
(Four-Wheel High,
Four-Wheel-High Lock or
Four-Wheel-Low Lock).
After the transfer case has
shifted out of Neutral the light
will go out.
4. Release the parking brake.Notice:Shifting the transmission
into gear before the indicator
light stops ashing could cause
damage to the transfer case.
Always wait until the indicator
light stops ashing before putting
the transmission back in gear.
5. You may start the engine and
shift the transmission to the
desired position.
Features and Controls 2-27

Using the CD Player
The CD player can play smaller
3 inch (8 cm) single CDs with
an adapter ring.
A CD in the player it stays in the
player when the ignition is turned off.
When the ignition or radio is
turned on, the CD starts to play
where it stopped, if it was the last
selected audio source.
Loading a CD
To load a CD do one of the
following:
Single CD Radio:
To Insert a CD with the ignition
on, insert the CD partway into
the slot, label side up, until
the player pulls the CD in. The
CD begins playing automatically.
To insert a CD with the ignition
off, press
Z(Eject) or the
DISP knob rst.The CD symbol displays when a CD
is inserted, and the track number
displays when each new track starts
to play.
Six-Disc CD Radio:
LOAD:Press to load CDs into the
CD player.
To insert one CD:
1. Turn the ignition on.
2. Press and release the LOAD
button.
3. Wait for the indicator light
comes on.
4. Insert the CD partway into the
slot, label side up, until the
player pulls the CD in. The CD
begins playing automatically.To insert multiple CDs:
1. Turn the ignition on.
2. Press and hold the LOAD button
for two seconds. The radio
beeps once, the indicator light
ashes, and LOAD # is
displayed.
3. Load a CD once INSERT CD #
displays and the light stops
ashing and illuminates. Insert
the CD partway into the slot,
label side up, until the player
pulls the CD in.
4. Repeat step 3 to load the
remaining CDs.
To load more than one CD but less
than six, complete Steps 1
through 3. When nished loading
CDs, press the LOAD button
to cancel the loading function. The
last CD loaded begins playing
automatically.
Playing a CD
B(CD):Press to play a CD while
listening to the radio.
Instrument Panel 3-47