low beam Hyundai Creta 2016 Owner's Manual

High Beam Indicator
Light
T h i s i n d i c a t o r l i g h t i l l u m i n a t e s :
• When the headlights are on and inthe high beam position
• When the turn signal lever is pulled into the FlashtoPass position.
Low Beam Indicator
Light (if equipped)
T h i s i n d i c a t o r l i g h t i l l u m i n a t e s :
When the headlights are on.
Light ON Indicator Light
T h i s i n d i c a t o r l i g h t i l l u
m i n a t e s :
When the parking lights or head
lights are on.
Front Fog Indicator Light
(if equipped)
T h i s i n d i c a t o r l i g h t i l l u m i n a t e s :
When the front fog lights are on.
Rear Fog Indicator Light
(if equipped)
T h i s i n d i c a t o r l i g h t i l l u m i n a t e s :
When the rear fog lights are on.
Cruise Indicator Light
(if equipped)
T h i s i n d i c a t o r l i g h t i l l u m i n a t e s :
• When the cruise control system isenabled.
For more details, refer to “Cruise
Control System” in chapter 5.
Cruise SET Indicator
Light (if equipped)
T h i s i n d i c a t o r l i g h t i l l u m i n a t e s :
• When the cruise control speed is set.
For more details, refer to “Cruise
Control System” in chapter 5.
3-54
Convenient features of your vehicle
SET
CRUISE

3-75
Convenient features of your vehicle
High beam operation
To turn on the high beam headlamp,
push the lever away from you. The
lever will return to its original position.
The high beam indicator will light
when the headlamp high beams are
switched on.
To turn off the high beam headlamp,
pull the lever towards you. The low
beams will turn on. To flash the high beam headlights,
pull the lever towards you, then
release the lever. The high beams
will remain ON as long as you hold
the lever towards you.
Rear fog light (if equipped)
Vehicle with front fog light
To turn on the rear fog light:
Position the light switch in the park
ing light position, turn the light switch
(1) to the front fog light position, and
then turn the light switch (1) to the
rear fog light position.
To turn the rear fog lights off, do one
of the following:
• Turn off the parking light switch.
• Turn the light switch to the rear fog light position again.
• When the light switch is in the parking light position, if you turn off
the front fog light, the rear fog light
will also turn off.
OGS045060L
Do not use high beam when there
are other vehicles approaching you.
Using high beam could obstruct the
other driver's vision.
WARNING
OGS045061L
OGS045062L

3-78
Convenient features of your vehicle
3
Daytime running light (DRL)
(if equipped)
The Daytime Running Lights (DRL)
can make it easier for others to see
the front of your vehicle during the
day, especially after dawn and beforesunset.
The DRL system will turn the dedi
cated lamp OFF when:
1. The headlights or front fog lightsare in the ON position.
2. The engine is turned off.
Headlamp leveling device
To adjust the headlamp beam level
according to the number of the pas
sengers and loading weight in the
luggage area, turn the beam leveling
switch. The higher the number of the switch
position, the lower the headlamp
beam level. Always keep the head
lamp beam at the proper leveling
position, or headlights may dazzle
other road users.
Listed below are the examples of
proper switch settings. For loading
conditions other than those listed
below, adjust the switch position so
that the beam level may be the near
est as the condition obtained accord
ing to the list.
OGS045064L
Loading conditionSwitch position
Driver only 0
Driver + Front passenger 0
Full passengers
(including driver) 1
Full passengers (including
driver) + Maximum permis
sible loading 2
Driver + Maximum permis
sible loading 3

3-79
Convenient features of your vehicle
Interior lights
Do not use the interior lights for
extended periods when the engine is
turned off or the battery will dis
charge.
Interior lamp AUTO cut
The interior lamps will automatically
go off approximately 20 minutes after
the engine is turned off and the
doors closed. If a door is opened, the
lamp will go off 40 minutes after the
engine is turned off. If the doors are
locked by the remote key or smart
key and the vehicle enters the armed
stage of the theft alarm system, the
lamps will go off five seconds later.
Front lamps
(1) Front Map Lamp
(2) Front Room Lamp
Front Map Lamp:
Press either the right or left lens to
turn the map lamp on or off. This light
produces a spot beam for convenient
use as a map lamp at night or as a
personal lamp for the driver and the
front passenger.
Front Room Lamp:
The Front Room Lamp Switch acti
vates the front and rear room lamps
when the switch is pressed in either of
the three positions indicated below:
: The front or rear room lampscome on when the front or rear
doors are opened if the engine
is running or not. When doors
are unlocked by the remote
key or smart key, the front and
rear lamps come on for
approximately 15 seconds as
long as any door is not
opened. The front and rear
room lamps go out gradually
after approximately 15 sec
onds if the door is closed.
However, if the ignition switch
is in the ON position or all
doors are locked, the front and
rear lamps will turn off immedi
ately. If a door is opened with
the ignition switch in the ACC
position or the LOCK/OFF
position, the front and rear
lamps stay on for about 20
minutes. However, if a door is
opened with the ignition switch
in the ON position, the lamps
stays on continuously.
NOTICE
OIB044015/Q
Do not use the interior lights when
driving in the dark. The interior
lights may obscure your view and
cause an accident.
WARNING

7-75
7
Maintenance
Engine Compartment Fuse Panel
ItemNameSymbolFuse RatingCircuit Protected
MULTIFUSEMDPS80AMDPS(Motor Power Steering)
ALTALT125A/150AG4FC (125A): Alternator, Battery, All Fuses connected to Alternator fuse
D4FC/D4FB (150A): Alternator, Battery, All Fuses connected to Alternator fuse
FUSE
ECU 2E210A/15AG4FC(10A): ECU (M/T), PCU(A/T)
D4FC(15A): CAM SNSR, Glow RLY, WGT,EGR Control Valve, Air Flow SNSR, IMMO
D4FB (15A): CAM SNSR, VGT Vacuum, IMMO
HEAD LAMPHIGH BEAM10AHead Lamp High Solenoid Relay (BiFunctional Type)
ABS 240AABS / ESC Control Module
ECU 4E425A/15AG4FC(25A): ECU (M/T), PCU(A/T)
D4FC(15A): Inlet Meter Valve,
D4FB(15A): Glow Plug Relay, Fuel Meter Unit
TCU 1625AD4FB: TCU(A/T)
B+540AInstrument Panel Fuse Block Fuse: FS01
ABS 140AABS / ESC Control Module, Engine Room Diagnosis
B+450AInstrument Panel Fuse Block Fuse: FS06, IPS1, IPS2, IPS3
* G4FC : Gamma 1.6 (Gasoline), D4FC : UII 1.4 (Diesel), D4FB : UII 1.6 (Diesel)

7-83
7
Maintenance
6. Install a new headlight bulb and
snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
BiFunction projection
headlamp
This headlamp is bifunction type that
switches the low beam to high or the
high beam to low using solenoid sys
tem. So, the moving sound may be
heard when the headlamp switches
the low beam to high or the high beam
to low and it does not indicate mal
function of the headlamp.
Turn signal light
1. Remove the turn signal light bulb cover by turning it counterclock
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
Front fog light bulb replacement
1.Remove the under cover by rotating the screws and bolts.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulbsocket from the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the housing.
5.Install the new bulbsocket into the housing by aligning the tabs on the
socket with the slots in the hous
ing. Push the socket into the hous
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
i