ignition Hyundai Getz 2002 Owner's Manual

1- 6 FEATURES OF YOUR HYUNDAI
password, consult your authorized Hyundai dealer.
1. To set the password you may turn
the ignition key "ON" and then turn it "OFF" according to the digit num- bers, then the immobilizer indicatorwill blink along with the operation ofthe ignition key. For example, turnthe ignition key once for digit num-ber "1", and twice for "2", and so on. However, for the digit number "0", you must turn the ignition key for 10times.
2. Wait for 3~10 seconds.
3. You may set the remaining number of digits by following the same pro- cedures 1 and 2.
4. If all of four digits have been tried successfully, turn the ignition key "ON" and check that the immobi-lizer indicator illuminates. From thistime, you have to start your engine within 30 seconds. If you start your engine after 30 seconds, your en-gine will not start.
HTB197
B880D02A-GAT Limp home procedures In case the immobilizer warning indi- cator blinks for five seconds when theignition key is turned to "ON" position, this indicates that the immobilizer sys- tem is out of order. And you cannotstart the engine without the limp homeprocedures with ignition key.The following procedure is how to startthe engine with the function of the limp home. (0, 1, 2, 3 as a sample pass- word). NOTE: You can get the limp home pass- word when the vehicle is first deliv-ered to you. If you do not have the NOTE: If the engine dies while driving after limp home procedure, you can startyour engine within 8 seconds with-out limp home procedure again.
5. If the immobilizer indicator blinks for
five seconds, you have to try the limp home procedure again fromthe beginning.
After doing the limp home procedure,you have to consult with your autho- rized Hyundai dealer as soon as pos- sible.
! CAUTION:
o If you fail to try the limp home procedure with the sequence of three times, you have to wait forabout one hour to do the limphome procedure again.
o If you cannot start your engine in
spite of limp home procedure,have your vehicle towed by anauthorized Hyundai dealer.

FEATURES OF YOUR HYUNDAI 1- 7
UNLOCK
B040A01A-AAT DOOR LOCKS
B040B01A-AATLocking and Unlocking Front Doors With a Key
HTB056
LOCK
!WARNING:
o Unlocked doors can be danger- ous. Before you drive away (es- pecially if there are children inthe car), be sure that all the doorsare securely closed and locked so that the doors cannot be inad- vertently opened from the inside.This helps ensure that doors willnot be opened accidentally. Also,when combined with the properuse of seat belts, locking the doors helps keep occupants from being ejected from the car in caseof an accident.
o Before opening the door, always look for and avoid oncoming traf-fic. o The door can be locked or unlocked
with a key.
o Lock the door by turning the key toward the front of the vehicle andunlock it by turning the key towardthe rear. B040C01FC-GAT Locking From the Outside The doors can be locked without a key. To lock the doors from the outside, firstpush the inside lock switch to the "LOCK" position, so that the red mark on the switch is not visible, then closethe door.The door will not lock if the key is left inthe ignition switch when the front doorsclose. This is normal. (If installed) NOTE:
o When locking the door this way,
be careful not to lock the door with the ignition key left in thevehicle. HTB062

1- 8 FEATURES OF YOUR HYUNDAI
To engage the child-protector feature so that the door cannot be openedfrom the inside, move the child-protec-tor lever to the " " position and closethe door. Move the lever to the oppo- site direction of the " " position when normal door operation is desired. If you wish to be able to open the door from the outside, the outside doorhandle will function normally.
HTB212
B040G01FC-GAT Central Door Lock (If Installed)
HTB057
UNLOCK
LOCK
B040D01FC-GAT Locking From the Inside To lock the doors from the inside, simply close the door and push thelock switch to the "LOCK" position.When this is done, neither the outsidenor the inside door handle can be used. B040E03A-AAT CHILD-PROTECTOR REAR DOOR LOCK Your Hyundai is equipped with a "child- protector" rear door lock assembly. When the lock mechanism is engaged,the rear door cannot be opened fromthe inside. It's use is recommendedwhenever there are small children inthe rear seat.
o To protect against theft, always
remove the ignition key, close allwindows, and lock all doors andtail gate when leaving your ve-hicle unattended. NOTE: When the door is locked, the red mark on the switch is not visibleand the character "LOCK" on theswitch is visible.
HTB058

FEATURES OF YOUR HYUNDAI 1- 9
HTB052 Park the car and stop the engine. Arm the system as described below.
1) Remove the ignition key from the
ignition switch.
2) Make sure that the engine hood and
tail gate are locked.
3) Lock the doors using the transmitter
of the keyless entry system.
After completion of the steps above, the turn signal lights will blink once to indicate that the system is armed. NOTE:
1) If any door, tail gate or engine hood remains open, the system will not be armed.
2) If this happens, rearm the system as described above.
The central door locking is operated bypushing the driver's door lock switchtoward the front or rear of the vehicle.If the passenger and rear doors areopen when the switch is pushed, the door will remain locked when closed. NOTE:
o When pushing the switch toward
the rear, all doors and tail gate will unlock.When pushing the switch towardthe front, all doors and tail gate will lock.
o When the door is unlocked, the red mark on the switch is visible and the character "LOCK" on theswitch is visible.
o The central door locking is oper- ated by turning the key (with theft-alarm system: driver's door andpassenger's door, without theft-alarm system: driver's door only)toward the front or rear of thevehicle. B070A01A-AAT THEFT-ALARM SYSTEM (If Installed) This system is designed to provide protection from unauthorized entry intothe car. This system is operated inthree stages: the first is the "Armed"stage, the second is the "Alarm" stage, and the third is the "Disarmed" stage. If triggered, the system provides anaudible alarm with blinking of the turnsignal lights. B070B01O-GAT Armed Stage
CAUTION:
Do not arm the system until all passengers have left the car. If thesystem is armed while apassenger(s) remains in the car,the alarm may be activated when the remaining passenger(s) leaves the car.
!

1- 10 FEATURES OF YOUR HYUNDAI
HTB202
B070D01TB-AAT Disarmed Stage
B070C01FC-GATAlarm Stage The alarm will be activated if any of the following occurs while the car is parkedand the system is armed.
1) A front or rear door is opened with-
out using the transmitter.
2) The tail gate is opened without us- ing the transmitter.
3) The engine hood is opened.The alarming horn will sound and the turn signal light will blink continuously for 27 seconds (E.C only/ Except E.C3 times). To turn off the system, unlockthe door or tail gate with the transmit-ter. The system will be disarmed when thedriver's or passenger's door is un-locked by depressing the button on the transmitter. After completion of the step above, the turn signal lights will blink twice toindicate that the system is disarmed. NOTE: Once the system has been dis- armed, it can not be rearmed exceptby repeating the arming procedures. CAUTION:
Only the transmitter can disarm thearmed stage. If the transmitter does not disarm the system, it is neces- sary to take the following steps;
1. Unlock the door with the key, which will cause, the alarm to be activated.
2. Insert the key in the ignition key
cylinder and turn the ignition keyto "ON" position.
3. Wait for 30 seconds. After completing the steps above, the system will be disarmed.
!

1- 12 FEATURES OF YOUR HYUNDAI
HTB257
B050A01A-AAT WINDOW GLASS
To raise or lower the window, turn the window regulator handle clockwise orcounterclockwise.HTB064
(1) HTB066
In order to prevent operation of the passenger front and rear windows, awindow lock switch is provided on thearmrest of the driver's door. To disablethe power windows, press the windowlock switch. To revert to normal operation, press the window lock switch a second time. Auto-Down Window (Driver's Side) The Auto-Down window is moved to its fully open position by pushing theswitch. To stop at the desired position push the switch again.
B060A01E-AAT POWER WINDOWS (If Installed)
The power windows operate when the ignition key is in the "ON" position. Themain switches are located on the driver's armrest and control the front and rear windows on both sides of thevehicle. The windows may be openedby depressing the appropriate windowswitch and closed by pulling up theswitch. To open the window on the driver's side, press the switch(1) down. The window moves as long as theswitch is operated.
WARNING:
When opening or closing the win-dows, make sure your passenger'sarms, hands and body are safelyout of the way.
!

FEATURES OF YOUR HYUNDAI 1- 13
HTB026
HTB024
B080A01FC-GAT ADJUSTABLE SEATS B080B01FC-GAT FRONT SEATS Adjusting Seat Forward andRearward
To move the seat toward the front or rear, pull the lock release lever up-ward. This will release the seat on itstrack so you can move it forward orrearward to the desired position. When you find the position you want, release the lever and slide the seat forward orrearward on its track until it locks intothe desired position and cannot bemoved further.
WARNING:
1) Be careful that someone's head, hands and body are not trappedby a closing window.
2) Never try to operate the main switch on the driver's door andthe individual door window switch in opposing directions at the same time. If this is done, thewindow will stop and cannot beopened or closed.
3) Do not leave children alone in the
car. Always remove the ignition key for their safety.
!
!WARNING:
Never attempt to adjust the seat while the vehicle is moving. This could result in loss of control, or an accident which may cause death,serious injury, or property damage.
B080C01A-AAT Adjusting Seatback Angle

FEATURES OF YOUR HYUNDAI 1- 33
WARNING:
To obtain maximum benefit from a pre-tensioner seat belt:
1. The seat belt must be worn cor- rectly.
2. The seat belt must be adjusted to
the correct position.!
NOTE:
o Both the driver's and frontpassenger's pre-tensioner seat belts will be activated in certainfrontal collisions. The pre- tensioner seat belts can be acti- vated with the airbags. The pre-tensioners will be activated un-der these conditions even if theseat belts are not being worn atthe time of the collision.
o When the pre-tensioner seat belts
are activated, a loud noise maybe heard and fine dust, whichmay appear to be smoke, may bevisible in the passenger com-partment. These are normal op- erating conditions and are not hazardous. illuminates while the vehicle isbeing driven, please have an au-thorized Hyundai dealer inspectthe pre-tensioner seat belt or SRSairbag system as soon as pos-sible.
WARNING:
o Pre-tensioners are designed to operate only one time. After acti- vation, pre-tensioner seat belts must be replaced. All seat belts,of any type, should always bereplaced after they have beenworn during a collision.
o The pre-tensioner seat belt as- sembly mechanisms become hotduring activation. Do not touchthe pre-tensioner seat belt as-semblies for several minutes af-ter they have been activated.
o Do not attempt to inspect or re- place the pre-tensioner seat beltsyourself. This must be done byan authorized Hyundai dealer.
o Do not strike the pre-tensioner seat belt assemblies.!
o Although it is harmless, the finedust may cause skin irritation and should not be breathed for pro-longed periods. Wash your handsand face thoroughly after an acci- dent in which the pre-tensioner seat belts were activated.
! CAUTION:
o Because the sensor that activates the SRS airbag is connected with the pre-tensioner seat belt, the SRS airbag warning light on the instrument panel will blink for ap-proximately 6 seconds after theignition key has been turned to the"ON" position, and then it should turn off.
o If the pre-tensioner seat belt is
not working properly, this warn- ing light will illuminate even ifthere is no malfunction of theSRS airbag system . If the SRS airbag warning light does not illuminate when the ignition keyis turned to "ON", or if it remainsilluminated after blinking for ap-proximately 6 seconds, or if it

1- 36 FEATURES OF YOUR HYUNDAI
The SRS consists of the following com- ponents:
- Driver's Airbag Module
- Passenger's Airbag Module
- SRS Service Reminder Indicator (SRI)
- SRS Control Module (SRSCM)
The SRSCM continually monitors allelements while the ignition is "ON" todetermine if a frontal or near-frontalimpact is severe enough to requireairbag deployment.
B240B01FC-GAT SRS Components and Functions
B240B01L
B240B02L
The SRS service reminder indicator (SRI) on the instrument panel will blinkfor about 6 seconds after the ignitionkey is turned to the "ON" position orafter the engine is started, after which the SRI should go out. The airbag modules are located both in the center of the steering wheel and inthe front passenger's panel above theglove box. When the SRSCM detects aconsiderable impact to the front of the vehicle, it will automatically deploy the airbags.
B240B03L

1- 38 FEATURES OF YOUR HYUNDAI
B990B03Y-GAT Side Impact Airbag (If Installed) Your Hyundai is equipped with a side airbag in each front seat. The purposeof the airbag is to provide the vehicle's driver and/or the front passenger with additional protection than that offeredby the seatbelt alone. The side impactairbags are designed to deploy onlyduring certain side impact collisions,depending on the crash severity, angle, speed and point of impact. The air bags are not designed to deploy in allside impact situations.o The SRS can function only when
the ignition key is in the "ON" position. If the SRS SRI does notcome on, or continuously re- mains on, after flashing for about 6 seconds when the ignition keyis turned to the "ON" position, orafter the engine is started, orcomes on while driving, the SRSis not working properly. If this occurs, have your vehicle imme- diately inspected by yourHyundai dealer.
o Before you replace a fuse or dis- connect a battery terminal, turn the ignition key to the "LOCK" position or remove the ignitionkey. Never remove or replace theair bag related fuse(s) when theignition key is in the "ON" posi-tion. Failure to heed this warning will cause the SRS SRI to illumi- nate.
B990B02Y
HTB072
Side airbag sensor
!WARNING:
o For best protection from the side impact airbag system and to avoid being injured by the de- ploying side impact airbag, both front seat occupants should sitin an upright position with theseat belt properly fastened. Thedriver's hands should be placedon the steering wheel at the 9:00 and 3:00 o'clock positions. The passenger's arms and handsshould be placed in their laps.
o Do not use any accessory seat covers.