warning lights HYUNDAI I10 2019 User Guide

Page 137 of 486

5-9
05
Unlocking
OAC3059004R
To unlock:
1. Carry the Smart Key.
2. Either press the door handle but-
ton or press the Door Unlock but-
ton (2) on the smart key.
3. The doors will unlock. The hazard
warning lights will blink two times.
i Information
‡ 7he door handle button will only
operate when the smart key is within
1 m (40 in.) from the outside door
handle. 2ther people can also open
the doors without the smart key in
possession.
‡ After unlocking the doors, the doors
will lock automatically after 30 sec-
onds unless a door is opened.
Tailgate unlocking
To unlock:
1. Carry the smart key.
2. Either press the tailgate handle
button or press the Tailgate Unlock
button (3) on the smart key for
more than one second.
3. The hazard warning lights will blink
two times.
Once the tailgate is opened and then
closed, the tailgate will lock automati-
cally.
i Information
After unlocking the tailgate, the tail-
gate will lock automatically after 30
seconds unless the tailgate is opened.

Page 146 of 486

5-18
Convenient features
This system helps to protect your
vehicle and valuables. The horn will
sound and the hazard warning lights
will blink continuously if any of the fol-
lowing occur:
- A door is opened without using the
remote key or smart key.
- The tailgate is opened without
using the remote key or smart key.
- The engine bonnet is opened.
The alarm continues for 30 seconds,
then the system resets. To turn off
the alarm, unlock the doors with the
remote key or smart key.
The Theft Alarm System automati-
cally sets 30 seconds after you lock
the doors and the tailgate. For the
system to activate, you must lock the
doors and the tailgate from outside
the vehicle with the remote key or
smart key or by pressing the button
on the outside of the door handles
with the smart key in your posses-
sion.
The hazard warning lights will blink
and the chime will sound once to indi-
cate the system is armed.
Once the security system is set,
opening any door, the tailgate, or the
bonnet without using the remote key
or smart key will cause the alarm to
activate.
The Theft Alarm System will not set if
the bonnet, the tailgate, or any door is
not fully closed. If the system will not
set, check the bonnet, the tailgate, or
the doors are fully closed.
Do not attempt to alter this system or
add other devices to it.i Information
‡ 'o not lock the doors until all pas-
sengers have left the vehicle. If the
remaining passenger leaves the vehi-
cle when the system is armed, the
alarm will be activated.
‡ If the vehicle is not disarmed with
the remote key or smart key, open
the doors by using the mechanical
key and place the ignition switch in
the 21 position (for remote key) or
start the engine (for smart key) and
wait for 30 seconds.
‡ When the system is disarmed but a
door or tailgate is not opened within
30 seconds, the system will be
rearmed.
WARNING
Be sure to receive the services
related to the burglar alarm system
be checked by a HYUNDAI autho-
rised repairer. Arbitrary modifica-
tion or alteration of the burglar
alarm system may result in a mal-
function. A failure caused by arbi-
trary alteration or modification is
not covered by the warranty.
THEFTØALARM SYSTEM

Page 149 of 486

5-21
05
Tilt steering / Telescope
steering
WARNING
Never adjust the steering wheel
whilst driving. You may lose steer-
ing control and cause severe per-
sonal injury, death or accidents.
i Information
After adjustment, sometimes the lock-
release lever may not lock the steering
wheel.
It is not a malfunction. 7his occurs
when two gears are not engaged cor-
rectly. In this case, adjust the steering
wheel again and then lock the steering
wheel.
OAC3059009R
To change the steering wheel angle
and height:
1. Pull down the lock-release lever
(1).
$GMXVW WKH VWHHULQJ ZKHHO WR WKH
desired angle (2) and height (3, if
equipped). Move the steering
wheel, so it points toward your
chest, not toward your face. Make
sure you can see the instrument
panel warning lights and gauges.
3. Pull up the lock-release lever to
lock the steering wheel in place.
Push the steering wheel both up and
down to be certain it is locked in posi-
tion.
CAUTION
Whilst adjusting the steering wheel
height, please do not push or pull
it hard since the fixture can be
damaged.

Page 151 of 486

5-23
05
Inside rearview mirror
%HIRUH \RX VWDUW GULYLQJ DGMXVW WKH
rearview mirror to the centre on the
view through the rear window.
WARNING
Make sure your line of sight is not
obstructed. Do not place objects in
the rear seat, cargo area, or behind
the rear head restraints which
could interfere with your vision
through the rear window.
WARNING
To prevent serious injury during
an accident or deployment of the
air bag, do not modify the rearview
mirror and do not install a wide
mirror.
WARNING
NEVER adjust the mirror whilst
driving. This may cause loss of
vehicle control resulting in an acci-
dent.
NOTICE
When cleaning the mirror, use a
paper towel or similar material
dampened with glass cleaner. Do
not spray glass cleaner directly on
the mirror as that may cause the
liquid cleaner to enter the mirror
housing.
Day/night rearview mirror
(if equipped)
OAH2048020
[A] : Day, [B] : Night
0DNHWKLVDGMXVWPHQWEHIRUH\RXVWDUW
GULYLQJ DQG ZKLOVW WKH GD\QLJKW OHYHU
is in the day position.
3XOO WKH GD\QLJKW OHYHU WRZDUGV \RX
to reduce glare from the headlights
of the vehicles behind you during
night driving.
Remember that you lose some rear-
view clarity in the night position.
MIRRORS

Page 264 of 486

6-8
Whilst driving
Key ignition switch positions
Switch
PositionAction Notice
/2&.The ignition key can be removed
in the LOCK position.The steering wheel locks to pro-
tect the vehicle from theft.
(if equipped)
ACCElectrical accessories are
usable.The steering wheel unlocks.
If difficulty is experienced turning
the ignition switch to the ACC
position, turn the key whilst turn-
ing the steering wheel right and
left to release tension.
ONThis is the normal key position
when the engine has started.
All features and accessories are
usable.
The warning lights can be
checked when you turn the igni-
tion switch from ACC to ON.Do not leave the ignition switch
in the ON position when the
engine is not running to prevent
the battery from discharging.
STARTTo start the engine, turn the igni-
tion switch to the START posi-
tion. The switch returns to the
ON position when you let go of
the key.The engine will crank until you
release the key.

Page 295 of 486

6-39
06
‡6WDWH
2$&78
3UHVV DQG KROG WKH (6& 2)) EXWWRQ
continuously for more than 3 sec-
onds. The ESC OFF indicator light
and/or message “Traction control and
ESC disabled” illuminates and a
warning chime sounds. In this state,
both the traction control function of
ESC (engine management) and the
brake control function of ESC (brak-
ing management) are disabled.
If the ignition switch is placed in the
LOCK/OFF position when ESC is off,
ESC remains off. Upon restarting the
vehicle, the ESC will automatically
turn on again.
Indicator lights
„ ESC indicator light (blinks)
„ ESC OFF indicator light (comes on)
27'
27'
When the ignition switch is in the ON
position, the ESC indicator light illu-
minates, then goes off if the ESC sys-
tem is operating normally.
The ESC indicator light blinks when-
ever the ESC is operating.
If the ESC indicator light stays on,
your vehicle may have a malfunction
with the ESC system. When this
warning light illuminates we recom-
mend that the vehicle be checked by
a HYUNDAI authorised repairer as
soon as possible.
The ESC OFF indicator light comes
on when the ESC is turned off with
the button.
WARNING
When the ESC is blinking, this
indicates the ESC is active:
Drive slowly and NEVER attempt
to accelerate. NEVER turn the ESC
off whilst the ESC indicator light is
blinking or you may lose control of
the vehicle resulting in an acci-
dent.

Page 300 of 486

6-44
Whilst driving
The ISG system is to reduce the fuel
consumption by automatically shut-
ting down the engine, when the vehi-
cle is at a standstill (i.e. red stop light,
VWRSVLJQDQGWUDIILFMDP 
The engine is automatically started
upon satisfying the starting condi-
tions.
The ISG system is always active,
when the engine is running.
i Information
When the engine is automatically
started by the IS* system, some warn-
ing lights (i.e. ABS, ESC, ESC 2FF,
EPS, and parking brake warning light)
may illuminate for a few seconds due
to the low battery voltage. +owever, it
does not indicate a malfunction with
the IS* system.
To activate the ISG system
Prerequisite for activation
The ISG system operates in the fol-
lowing situations.
‡ 7KHGULYHU‹VVHDWEHOWLVIDVWHQHG

Page 355 of 486

7-3
07
OAC3079001TU
The hazard warning flasher serves as
a warning to other drivers to exercise
extreme caution when approaching,
overtaking, or passing your vehicle.
It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
To turn the hazard warning flasher on
or off, press the hazard warning flash-
er button with the ignition switch in
any position. The button is located in
the centre fascia panel. All turn signal
lights will flash simultaneously.
‡The hazard warning flasher oper-
ates whether your vehicle is run-
ning or not.
‡The turn signals do not work when
the hazard flasher is on
HAZARD WARNING FLASHER IN CASE OF AN EMERGENCY
WHILST DRIVING
,IWKHHQJLQHVWDOOVZKLOVW
GULYLQJ
‡Reduce your speed gradually,
keeping a straight line. Move cau-
tiously off the road to a safe place.
‡Turn on your hazard warning flash-
er.
‡Try to start the engine again. If your
vehicle will not start, we recom-
mend that you contact a HYUNDAI
authorised repairer.
,IWKHHQJLQHVWDOOVDWDFURVV-
URDGRUFURVVLQJ
If the engine stalls at a crossroads or
crossing, if safe to do so, move the
shift lever to the N (Neutral) position
and then push the vehicle to a safe
location.

Page 446 of 486

8-50
Maintenance
&RQVXOW D +<81'$, DXWKRULVHG UH-
SDLUHU WR UHSODFH PRVW YHKLFOH OLJKW
EXOEV ,W LV GLIILFXOW WR UHSODFH YHKLFOH
OLJKWEXOEVEHFDXVHRWKHUSDUWVRIWKH
YHKLFOH PXVW EH UHPRYHG EHIRUH \RX
FDQJHWWRWKHEXOE7KLVLVHVSHFLDOO\
WUXH IRU UHPRYLQJ WKH KHDGOLJKW DV-
VHPEO\WRJHWWRWKHEXOE V 
5HPRYLQJLQVWDOOLQJWKHKHDGOLJKWDV-
VHPEO\ FDQ UHVXOW LQ GDPDJH WR WKH
vehicle.
WARNING
Prior to replacing a light, depress
the foot brake, move the shift lever
into the N (Neutral, for Automated
manual transmission vehicle) or
neutral (for manual transmission
vehicle), apply the parking brake,
place the ignition switch in the
LOCK/OFF position, and take the
key with you when leaving the ve-
hicle to avoid sudden movement
of the vehicle and to prevent pos-
sible electric shock.
Be aware the bulbs may be hot and
may burn your fingers.
NOTICE
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause
damage to the fuse or electric wir-
ing system.
i Information
The headlight and tail lamp lenses
could appear frosty if the vehicle is
washed after driving or the vehicle is
driven at night in wet weather. This
condition is caused by temperature dif-
ference between the lamp inside and
outside and, it does not indicate a
problem with your vehicle. When
moisture condenses in the lamp, it will
be removed after driving with the
headlight on. The removable level may
differ depending on lamp size, lamp
position and environmental condition.
However, if moisture is not removed,
we recommend that your vehicle is in-
spected by a HYUNDAI authorised re-
pairer.
i Information (For Europe)
Traffic Change
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direction,
this asymmetric part will dazzle on-
coming car driver. To prevent dazzle,
ECE regulation demand several tech-
nical solutions (ex. automatic change
system, adhesive sheet, down aiming).
These headlights are designed not to
dazzle opposite drivers. So, you need
not change your headlights in a coun-
try with opposite traffic direction.
LIGHT BULBS

Page 479 of 486

I-7
I
If you have a flat tyre (with tyre mobility kit) ..................................................... 7-25
Introduction ...................................................................................................... 7-25
Notes on the safe use of the tyre Mobility Kit ................................................. 7-26
Components of the Tyre Mobility Kit .............................................................. 7-27
Using the Tyre Mobility Kit ............................................................................. 7-28
Distributing the sealant ..................................................................................... 7-30
Checking the tyre inflation pressure ................................................................. 7-30
Ignition switch ....................................................................................................... 6-7
Key ignition switch ........................................................................................... 6-7
Engine Start/Stop button ................................................................................. 6-10
Important safety precautions.................................................................................. 3-2
Always wear your seat belt ................................................................................ 3-2
Restrain all children ........................................................................................... 3-2
Air bag hazards ................................................................................................... 3-2
Driver distraction ................................................................................................ 3-2
Control your speed ............................................................................................. 3-3
Keep your vehicle in safe condition ................................................................... 3-3
In case of an emergency whilst driving ................................................................. 7-3
If the engine stalls whilst driving ....................................................................... 7-3
If the engine stalls at a crossroad or crossing ..................................................... 7-3
If you have a flat tyre whilst driving .................................................................. 7-4
Infotainment system............................................................................................. 5-90
USB port ........................................................................................................... 5-90
Antenna ............................................................................................................ 5-90
Steering wheel audio control ............................................................................ 5-91
Audio / Video / Navigation system .................................................................. 5-92
Bluetooth
® Wireless Technology hands-free ................................................... 5-93
How vehicle radio works .................................................................................. 5-93
Infotainment System specifications ................................................................... 5-125
Instrument cluster .................................................................................................. 4-2
Instrument cluster control ................................................................................... 4-3
Gauges and meters ............................................................................................. 4-3
Transmission shift indicator ............................................................................... 4-7
Warning and indicator lights .............................................................................. 4-8
LCD display messages ..................................................................................... 4-20

Page:   < prev 1-10 11-20