ECU HYUNDAI I10 2019 Owners Manual

Page 44 of 486

3-12
Safety system
WARNING
Cargo
Cargo should always be secured
to prevent it from being thrown
about the vehicle in a collision and
causing injury to the vehicle occu-
pants. Do not place objects in the
rear seats, since they cannot be
properly secured and may hit the
front seat occupants in a collision.
WARNING
Cargo loading
Make sure the engine is off, the
Automated manual transmission
is in N (Neutral) or the Manual
transmission is in R (Reverse) or
1st, and the parking brake is
securely applied whenever loading
or unloading cargo. Failure to take
these steps may allow the vehicle
to move if the shift lever is inadver-
tently moved to another position.
Head restraint
The vehicle’s front and rear seats
have adjustable head restraints. The
head restraints provide comfort for
passengers, but more importantly
they are designed to help protect
passengers from whiplash and other
neck and spinal injuries during an
accident, especially in a rear impact
collision.
WARNING
To reduce the risk of serious injury
or death in an accident, take the
following precautions when adjust-
ing your head restraints:
‡Always properly adjust the head
restraints for all passengers
BEFORE starting the vehicle.

Page 50 of 486

3-18
Safety system
SEAT BELTS
This section describes how to use the
seat belts properly. It also describes
some of the things not to do when
using seat belts.
Seat belt safety precautions
Always fasten your seat belt and
make sure all passengers have fas-
tened their seat belts before starting
any trip. Air bags (if equipped) are
designed to supplement the seat belt
as an additional safety device, but
they are not a substitute. Most coun-
tries require all occupants of a vehicle
to wear seat belts.
WARNING
Seat belts must be used by ALL
passengers whenever the vehicle
is moving. Take the following pre-
cautions when adjusting and wear-
ing seat belts:
‡ALWAYS properly restrain chil-
dren under age 13 in the rear
seats.
‡NEVER allow children to ride in
the front passenger seat. If a
child age 13 or older must be
seated in the front seat, move the
seat as far back as possible and
properly restrain them in the
seat.
‡NEVER allow an infant or child to
be carried on an occupant’s lap.
‡NEVER ride with the seatback
reclined when the vehicle is mov-
ing.
‡Do not allow children to share a
seat or seat belt.
‡Do not wear the shoulder belt
under your arm or behind your
back.‡Never wear a seat belt over frag-
ile objects. If there is a sudden
stop or impact, the seat belt can
damage it.
‡Do not use the seat belt if it is
twisted. A twisted seat belt will
not protect you properly in an
accident.
‡Do not use a seat belt if the web-
bing or hardware is damaged.
‡Do not latch the seat belt into the
buckles of other seats.
‡NEVER unfasten the seat belt
whilst driving. This may cause
loss of vehicle control resulting
in an accident.
‡Make sure there is nothing in the
buckle interfering with the seat
belt latch mechanism. This may
prevent the seat belt from fasten-
ing securely.
‡No modifications or additions
should be made by the user
which will either prevent the seat
belt adjusting devices from oper-
ating to remove slack, or prevent
the seat belt assembly from
being adjusted to remove slack.
WARNING
Damaged seat belts and seat belt
assemblies will not operate prop-
erly. Always replace:
‡Frayed, contaminated, or dam-
aged webbing.
‡Damaged hardware.
‡The entire seat belt assembly
after it has been worn in an acci-
dent, even if damage to webbing
or assembly is not apparent.

Page 59 of 486

3-27
03
Seat belt use and children
Infant and small children
Most countries have child restraint
laws which require children to travel
in approved child restraint devices,
including booster seats. The age at
which seat belts can be used instead
of child restraints differs among coun-
tries, so you should be aware of the
specific requirements in your country,
and where you are travelling. Infant
and child restraints must be properly
placed and installed in a rear seat.
For more details, refer to the “Child
Restraint Systems” in this chapter.
WARNING
ALWAYS properly restrain infants
and small children in a child restraint
appropriate for the child’s height
and weight.
To reduce the risk of serious injury
or death to a child and other passen-
gers, NEVER hold a child in your lap
or arms when the vehicle is moving.
The violent forces created during an
accident will tear the child from your
arms and throw the child against the
interior of the vehicle.
Small children are best protected
from injury in an accident when prop-
erly restrained in the rear seat by a
child restraint system that meets the
requirements of the Safety Standards
of your country. Before buying any
child restraint system, make sure that
it has a label certifying that it meets
Safety Standard of your country. The
restraint must be appropriate for your
child’s height and weight. Check the
label on the child restraint for this
information. Refer to “Child Restraint
Systems” in this chapter.
Larger children
Children under age 13 and who are
too large for a booster seat must
always occupy the rear seat and use
the available lap/shoulder belts. A
seat belt should lie across the upper
thighs and be snug across the shoul-
der and chest to restrain the child
safely. Check belt fit periodically. A
child’s squirming could put the belt
out of position. Children are afforded
the most safety in the event of an
accident when they are restrained by
a proper restraint system and/or seat
belts in the rear seat.
If a larger child over age 13 must be
seated in the front seat, the child
must be securely restrained by the
available lap/shoulder belt and the
seat should be placed in the rearmost
position.
If the shoulder belt portion slightly
touches the child’s neck or face, try
placing the child closer to the centre
of the vehicle. If the shoulder belt still
touches their face or neck, they need
to be returned to an appropriate
booster seat in the rear seat.
WARNING
‡Always make sure larger chil-
dren’s seat belts are worn and
properly adjusted.
‡NEVER allow the shoulder belt to
contact the child’s neck or face.
‡Do not allow more than one child
to use a single seat belt.

Page 61 of 486

3-29
03
CHILD RESTRAINT SYSTEM ãCRSä
Our recommendation:
Children always in the rear
WARNING
Always properly restrain children
in the rear seats of the vehicle,
unless the air bag on the front pas-
senger seat is deactivated.
Children of all ages are safer when
restrained in the rear seat. A child
riding in the front passenger seat
can be forcefully struck by an
inflating air bag resulting in
SERIOUS INJURY or DEATH.
Children under age 13 must always
ride in the rear seats and must always
be properly restrained to minimise
the risk of injury in an accident, sud-
den stop or sudden manoeuvre.
According to accident statistics, chil-
dren are safer when properly
restrained in the rear seats than in
the front seat. Children too large for a
Child Restraint System must use the
seat belts provided.
Most countries have Child Restraint
Systems which require children to
travel in approved Child Restraint
Systems. The laws governing the age
or height/weight restrictions at which
seat belts can be used instead of
Child Restraint System differs among
countries, so you should be aware of
the specific requirements in your
country, and where you are travelling.Child Restraint Systems must be
properly placed and installed in the
rear seat. You must use a commer-
cially available Child Restraint
System that meets the requirements
of the Safety Standards of your coun-
try.
Child Restraint Systems are general-
ly designed to be secured in a vehicle
seat by lap belt or the lap belt portion
of a lap/shoulder belt, or by a top-
tether and/or ISOFIX anchorage in
the rear seats of the vehicle.
Child Restraint System (CRS)
always in the rear
Infants and younger children must be
restrained in an appropriate rear-
ward-facing or forward-facing CRS
that has first been properly secured
to the rear seat of the vehicle. Read
and comply with the instructions for
installation and use provided by the
manufacturer of the Child Restraint
System.
WARNING
‡Always follow the Child Restraint
System manufacturer’s instruc-
tions for installation and use.
‡Always properly restrain your
child in the Child Restraint
System.
‡Do not use an infant carrier or a
child safety seat that “hooks”
over a seatback, it may not pro-
vide adequate protection in an
accident.
‡After an accident, we recom-
mend a HYUNDAI dealer check
the Child Restraint System, seat
belts, ISOFIX anchorages and
top-tether anchorages.

Page 63 of 486

3-31
03
OIB034017
Forward-facing Child Restraint
System
A forward-facing Child Restraint
System provides restraint for the
child’s body with a harness. Keep
children in a forward-facing Child
Restraint System with a harness until
they reach the top height or weight
limit allowed by your Child Restraint
System’s manufacturer.
Once your child outgrows the for-
ward-facing Child Restraint System,
your child is ready for a booster seat.
Booster seats
A booster seat is Child Restraint
System designed to improve the fit of
the vehicle’s seat belt system. A
booster seat positions the seat belt
so that it fits properly over the stron-
ger parts of your child’s body. Keep
your children in booster seats until
they are big enough to fit in a seat
belt properly.
For a seat belt to fit properly, the lap
belt must lie comfortable across the
upper thighs, not the stomach. The
shoulder belt should lie comfortable
across the shoulder and chest and
not across the neck or face. Children
under age 13 must always be prop-
erly restrained to minimise the risk of
injury in an accident, sudden stop or
sudden manoeuvre.
Installing a Child Restraint
System (CRS)
WARNING
Before installing your Child
Restraint System always:
Read and follow the instructions
provided by the manufacturer of
the Child Restraint System.
Failure to follow all warnings and
instructions could increase the
risk of the SERIOUS INJURY or
DEATH if an accident occurs.
WARNING
If the vehicle head restraint pre-
vents proper installation of a Child
Restraint System, the head
restraint of the respective seating
position shall be readjusted or
entirely removed.
After selecting a proper Child
Restraint System and checking that
the Child Restraint System fits prop-
erly in the rear of this vehicle, you are
ready to install the Child Restraint
System according to the manufactur-
er’s instruction. There are three gen-
eral steps in installing the Child
Restraint Systems properly:
‡Properly secure the Child
Restraint System to the vehicle.
All Child Restraint System must be
secured to the vehicle with the lap
belt or lap part of a lap/shoulder belt
or with the ISOFIX top-tether and/or
ISOFIX anchorage.

Page 64 of 486

3-32
Safety system
‡Make sure the Child Restraint
System is firmly secured. After
installing a Child Restraint System
to the vehicle, push and pull the
seat forward and from side-to-side
to verify that it is securely attached
to the seat. A Child Restraint
System secured with a seat belt
should be installed as firmly as pos-
sible. However, some side-to- side
movement can be expected.
When installing a Child Restraint
System, adjust the vehicle seat (up
and down, forward and rearward)
so that your child fits in the Child
Restraint System in a comfortable
manner.
‡Secure the child in the Child
Restraint System. Make sure the
child is properly strapped in the
Child Restraint System according
to the Child Restraint System man-
ufacturer’s instructions.
CAUTION
A Child Restraint System in a
closed vehicle can become very
hot. To prevent burns, check the
seating surface and buckles before
placing your child in the Child
Restraint System.
ISOFIX anchorage and top-tether
anchorage (ISOFIX anchorages
system) for children
The ISOFIX system holds a Child
Restraint System during driving and
in an accident. This system is
designed to make installation of the
Child Restraint System easier and
reduce the possibility of improperly
installing your Child Restraint System.
The ISOFIX system uses anchors in
the vehicle and attachments on the
Child Restraint System. The ISOFIX
system eliminates the need to use
seat belts to secure the Child
Restraint System to the rear seats.
ISOFIX anchorages are metal bars
built into the vehicle. There are two
lower anchors for each ISOFIX seat-
ing position that will accommodate a
Child Restraint System with lower
attachments.
To use the ISOFIX system in your
vehicle, you must have a Child
Restraint System with ISOFIX attach-
ments. (An ISOFIX Child Restraint
System may only be installed if it has
vehicle-specific or universal approval
in accordance with the requirements
of ECE-R44 or ECE-R129.)
The Child Restraint System manufac-
turer will provide you with instructions
on how to use the Child Restraint
System with its attachments for the
ISOFIX anchorages.

Page 66 of 486

3-34
Safety system
Securing a Child Restraint
System with the “ISOFIX
Anchorage System”
To install a ISOFIX-compatible Child
Restraint System in either of the rear
outboard seating positions:
1. Move the seat belt buckle away
from the ISOFIX anchorages.
2. Move any other objects away from
the anchors that could prevent a
secure connection between the
Child Restraint System and the
ISOFIX anchorages.
3. Place the Child Restraint System
on the vehicle seat, then attach the
seat to the ISOFIX anchorages
according to the instructions pro-
vided by the Child Restraint
System manufacturer.
4. Follow the instructions of the Child
Restraint System’s manufacturer
for proper installation and connec-
tion of the ISOFIX attachments on
the Child Restraint System to the
ISOFIX anchorages.
WARNING
Take the following precautions
when using the ISOFIX system:
‡Read and follow all installation
instructions provided with your
Child Restraint System.
‡To prevent the child from reach-
ing and taking hold of unretract-
ed seat belts, buckle all unused
rear seat belts and retract the
seat belt webbing behind the
child. Children can be strangled
if a shoulder belt becomes
wrapped around their neck and
the seat belt tightens.
‡NEVER attach more than one
Child Restraint System to a sin-
gle anchorage. This could cause
the anchor or attachment to
come loose or break.
‡Always have the ISOFIX system
inspected by your dealer after an
accident. An accident can dam-
age the ISOFIX system and may
not properly secure the Child
Restraint System.

Page 67 of 486

3-35
03
Securing a Child Restraint
System seat with “Top-tether
Anchorage” system
OAC3039011TU
Top-tether anchorages for Child
Restraint Systems are located on the
rear of the seatback.
OAC3039012TU
1. Route the Child Restraint System
seat strap over the seatback.
For vehicles with adjustable head
restraint, route the tether strap
under the head restraint and
between the head restraint posts,
otherwise route the tether strap
over the top of the seatback.
2. Connect the top-tether to the top-
tether anchorage, then tighten the
top-tether according to the instruc-
tions of your Child Restraint
System’s manufacturer to firmly
attach the Child Restraint System
to the seat.
WARNING
Take the following precautions
when installing the top-tether:
‡Read and follow all installation
instructions provided with your
Child Restraint System.
‡NEVER attach more than one
Child Restraint System to a sin-
gle ISOFIX top-tether anchorage.
This could cause the anchorage
or attachment to come loose or
break.
‡Do not attach the top-tether to
anything other than the correct
top-tether anchorage. It may not
work properly if attached to
something else.
‡Child Restraint anchorages are
designed to withstand only those
loads imposed by correctly fitted
Child Restraint System.
Under no circumstances are they
to be used for adult seat belts or
harnesses or for attaching other
items or equipment to the vehi-
cle.

Page 70 of 486

3-38
Safety system
WARNING
‡Never place a Child Restraint
System on the front passenger
seat, unless the passenger air
bag is deactivated.
‡For semi-universal or vehicle
specific CRS (ISOFIX or belted
CRS), please see the vehicle list
provided in the manual of CRS.
‡It is recommended to remove the
head restraint, when CRS is
unstable due to head restraint.
Securing a Child Restraint
System with a lap/shoulder belt
When not using the ISOFIX system,
all Child Restraint Systems must be
secured to a rear seat with the lap
part of a lap/shoulder belt.
OHI038145
Installing a Child Restraint System
with a lap/shoulder belt
To install a Child Restraint System on
the rear seats, do the following:
1. Place the Child Restraint System
on a rear seat and route the lap/
shoulder belt around or through
the restraint, following the restraint
manufacturer’s instructions. Make
sure the seat belt webbing is not
twisted.
i Information
When using the rear centre seat belt,
you should also refer to the “Rear
Centre Seat Belt” in this chapter.

Page 79 of 486

3-47
03
WARNING
To reduce the risk of serious injury
or death from an inflating curtain
air bags, take the following pre-
cautions:
‡All seat occupants must wear
seat belts at all times to help
keep occupants positioned prop-
erly.
‡Properly secure child restraints
as far away from the door as pos-
sible.
‡Do not place any objects over
the air bag. Also, do not attach
any objects around the area the
air bag inflates such as the door,
side door glass, front and rear
pillar, roof side rail.
‡Do not hang other objects except
clothes, especially hard or break-
able objects. In an accident, it
may cause vehicle damage or
personal injury.
‡Do not allow passengers to lean
their heads or bodies onto doors,
put their arms on the doors,
stretch their arms out of the win-
dow, or place objects between
the doors and seats.
‡Do not open or repair the side
curtain air bags.
How does the air bags system
operate?
OAC3039023R
The SRS consists of the following
components:
(1) Driver’s front air bag module
(2) Passenger’s front air bag module*
(3) Side air bag modules*
(4) Curtain air bag modules*
(5) Retractor pre-tensioner assem-
blies*
(6) Air bag warning light
(7) SRS control module (SRSCM)/
Rollover sensor*
(8) Front impact sensors
(9) Side impact sensors*
(10) Side pressure sensors*
(11) Passenger’s front air bag OFF
indicator (front passenger’s seat
only) *
(12) Passenger’s front air bag ON/
OFF switch *
* : if equipped
The SRSCM continually monitors
SRS components whilst the ignition
switch is in the ON position to deter-
mine if a crash impact is severe
enough to require air bag deployment
or pre-tensioner seat belt deploy-
ment.

Page:   1-10 11-20 21-30 next >