brake light HYUNDAI I10 2020 User Guide

Page 291 of 486

6-35
06
Parking brake warning light
 &KHFN WKH 3DUNLQJ %UDNH
Warning Light by placing
the ignition switch to the
ON position (do not start
the engine).
This light will be illuminated when the
parking brake is applied with the igni-
tion switch in the START or ON posi-
tion.
%HIRUH GULYLQJ EH VXUH WKH SDUNLQJ
EUDNH LV UHOHDVHG DQG WKH %UDNH
Warning Light is OFF.
,I WKH 3DUNLQJ %UDNH :DUQLQJ /LJKW
remains on after the parking brake is
released whilst the engine is running,
there may be a malfunction in the
brake system. Immediate attention is
necessary.
If at all possible, cease driving the
vehicle immediately. If that is not pos-
sible, use extreme caution whilst
operating the vehicle and only con-
tinue to drive the vehicle until you can
reach a safe location.
Anti-lock Brake System (ABS)
WARNING
$Q $QWL/RFN %UDNLQJ 6\VWHP
(ABS) or an Electronic Stability
Control (ESC) system will not pre-
vent accidents due to improper or
dangerous driving manoeuvres.
Even though vehicle control is
improved during emergency brak-
ing, always maintain a safe dis-
tance between you and objects
ahead of you. Vehicle speeds
should always be reduced during
extreme road conditions. The brak-
ing distance for vehicles equipped
with ABS or ESC may be longer
than for those without these sys-
tems in the following road condi-
tions.
Drive your vehicle at reduced
speeds during the following condi-
tions:

Page 292 of 486

6-36
Whilst driving
Using ABS
To obtain the maximum benefit from
\RXU$%6 LQ DQ HPHUJHQF\ VLWXDWLRQ
do not attempt to modulate your
brake pressure and do not try to
pump your brakes. Depress your
brake pedal as hard as possible.
When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the
brakes, or feel a corresponding sen-
sation in the brake pedal. This is nor-
PDODQGLWPHDQV\RXU$%6LVDFWLYH
$%6GRHVQRWUHGXFHWKHWLPHRUGLV-
tance it takes to stop the vehicle.
Always maintain a safe distance from
the vehicle in front of you.
$%6ZLOOQRWSUHYHQWDVNLGWKDWUHVXOWV
from sudden changes in direction,
such as trying to take a corner too
fast or making a sudden lane change.
Always drive at a safe speed for the
road and weather conditions.
$%6 FDQQRW SUHYHQW D ORVV RI VWDELOL-
ty. Always steer moderately when
braking hard. Severe or sharp steer-
ing wheel movement can still cause
your vehicle to veer into oncoming
traffic or off the road.
On loose or uneven road surfaces,
operation of the anti-lock brake sys-
tem may result in a longer stopping
distance than for vehicles equipped
with a conventional brake system.
7KH$%6ZDUQLQJOLJKW
) will stay
on for several seconds after the igni-
tion switch is in the ON position.
'XULQJ WKDW WLPH WKH $%6 ZLOO JR
through self-diagnosis and the light
will go off if everything is normal. If
the light stays on, you may have a
SUREOHP ZLWK \RXU $%6 :H UHFRP-
mend that you contact a HYUNDAI
authorised repairer as soon as pos-
sible.
WARNING
If the ABS warning light () is on
and stays on, you may have a
problem with the ABS. Your power
brakes will work normally. To
reduce the risk of serious injury or
death, we recommend that you
contact a HYUNDAI authorised
repairer as soon as possible.
NOTICE
When you drive on a road having
poor traction, such as an icy road,
and apply your brakes continuous-
ly, the ABS will be active continu-
ously and the ABS warning light
(
) may illuminate. Pull your
vehicle over to a safe place and
turn the engine off.
Restart the engine. If the ABS
warning light is off, then your ABS
system is normal.
Otherwise, you may have a prob-
lem with your ABS system. We rec-
ommend that you contact a
HYUNDAI authorised repairer as
soon as possible.
i Information
When you jump start your vehicle
because of a drained battery, the ABS
warning light (
) may turn on at the
same time. 7his happens because of the
low battery voltage. It does not mean
your ABS is malfunctioning. +ave the
battery recharged before driving the
vehicle.

Page 295 of 486

6-39
06
‡6WDWH
2$&78
3UHVV DQG KROG WKH (6& 2)) EXWWRQ
continuously for more than 3 sec-
onds. The ESC OFF indicator light
and/or message “Traction control and
ESC disabled” illuminates and a
warning chime sounds. In this state,
both the traction control function of
ESC (engine management) and the
brake control function of ESC (brak-
ing management) are disabled.
If the ignition switch is placed in the
LOCK/OFF position when ESC is off,
ESC remains off. Upon restarting the
vehicle, the ESC will automatically
turn on again.
Indicator lights
„ ESC indicator light (blinks)
„ ESC OFF indicator light (comes on)
27'
27'
When the ignition switch is in the ON
position, the ESC indicator light illu-
minates, then goes off if the ESC sys-
tem is operating normally.
The ESC indicator light blinks when-
ever the ESC is operating.
If the ESC indicator light stays on,
your vehicle may have a malfunction
with the ESC system. When this
warning light illuminates we recom-
mend that the vehicle be checked by
a HYUNDAI authorised repairer as
soon as possible.
The ESC OFF indicator light comes
on when the ESC is turned off with
the button.
WARNING
When the ESC is blinking, this
indicates the ESC is active:
Drive slowly and NEVER attempt
to accelerate. NEVER turn the ESC
off whilst the ESC indicator light is
blinking or you may lose control of
the vehicle resulting in an acci-
dent.

Page 298 of 486

6-42
Whilst driving
Emergency Stop Signal (ESS)
The Emergency Stop Signal system
alerts the driver behind by blinking
the stop light when the vehicle is
braked rapidly and severely.
7KHV\VWHPLVDFWLYDWHGZKHQ

Page 299 of 486

6-43
06
Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it
is washed.
Your vehicle will not stop as quickly if
the brakes are wet. Wet brakes may
cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns
to normal. If the braking action does
not return to normal, stop as soon as
it is safe to do so and we recommend
that you call a HYUNDAI authorised
repairer for assistance.
DO NOT drive with your foot resting
on the brake pedal. Even light, but
constant pedal pressure can result in
the brakes overheating, brake wear,
and possibly even brake failure.
If a tyre goes flat whilst you are driv-
ing, apply the brakes gently and keep
the vehicle pointed straight ahead
whilst you slow down. When you are
moving slowly enough for it to be safe
to do so, pull off the road and stop in
a safe location.
Keep your foot firmly on the brake
pedal when the vehicle is stopped to
prevent the vehicle from rolling for-
ward.

Page 300 of 486

6-44
Whilst driving
The ISG system is to reduce the fuel
consumption by automatically shut-
ting down the engine, when the vehi-
cle is at a standstill (i.e. red stop light,
VWRSVLJQDQGWUDIILFMDP 
The engine is automatically started
upon satisfying the starting condi-
tions.
The ISG system is always active,
when the engine is running.
i Information
When the engine is automatically
started by the IS* system, some warn-
ing lights (i.e. ABS, ESC, ESC 2FF,
EPS, and parking brake warning light)
may illuminate for a few seconds due
to the low battery voltage. +owever, it
does not indicate a malfunction with
the IS* system.
To activate the ISG system
Prerequisite for activation
The ISG system operates in the fol-
lowing situations.
‡ 7KHGULYHU‹VVHDWEHOWLVIDVWHQHG

Page 347 of 486

6-91
06
The severe weather conditions of
winter quickly wear out tyres and
cause other problems. To minimise
winter driving problems, you should
WDNHWKHIROORZLQJVXJJHVWLRQV
Snow or icy conditions
You need to keep sufficient distance
between your vehicle and the vehicle
in front of you.
Apply the brakes gently. Speeding,
rapid acceleration, sudden brake
applications, and sharp turns are
potentially very hazardous practices.
During deceleration, use engine brak-
ing to the fullest extent. Sudden brake
applications on snowy or icy roads
may cause the vehicle to skid.
To drive your vehicle in deep snow, it
may be necessary to use snow tyres
or to install tyre chains on your tyres.
Always carry emergency equipment.
Some of the items you may want to
carry include tyre chains, tow straps
or chains, a flashlight, emergency
IODUHVVDQGDVKRYHOMXPSHUFDEOHV
a window scraper, gloves, ground
cloth, coveralls, a blanket, etc.
Snow tyres
WARNING
Snow tyres should be equivalent
in size and type to the vehicle’s
standard tyres. Otherwise, the
safety and handling of your vehi-
cle may be adversely affected.
If you mount snow tyres on your vehi-
cle, make sure to use radial tyres of
the same size and load range as the
RULJLQDOW\UHV0RXQWVQRZW\UHVRQDOO
four wheels to balance your vehicle’s
handling in all weather conditions.
The traction provided by snow tyres
on dry roads may not be as high as
your vehicle’s original equipment
tyres. Check with the tyre dealer for
maximum speed recommendations.
i Information
'o not install studded tyres without
first checking local and municipal reg-
ulations for possible restrictions
against their use.
WINTER DRIVING

Page 350 of 486

6-94
Whilst driving
To prevent locks from freezing
To prevent the locks from being fro-
zen, spray approved de-icing fluid or
glycerin into key holes. When a lock
opening is already covered with ice,
spray approved de-icing fluid over the
ice to remove it. When an internal
part of a lock freezes, try to thaw it
with a heated key. Carefully use the
KHDWHGNH\WRDYRLGDQLQMXU\
Use approved window washer anti-
freeze solution in system
To prevent the window washer from
being frozen, add authorized window
washer anti-freeze solution, as speci-
fied on the window washer container.
Window washer anti-freeze solution
is available from a HYUNDAI autho-
rised repairer, and most vehicle
accessory outlets. Do not use engine
coolant or other types of anti-freeze
solution to prevent any damage to the
vehicle paint.
Do not let your parking brake
freeze
Under some conditions your parking
brake can freeze in the engaged posi-
tion.
This is most likely to happen when
there is an accumulation of snow or
ice around or near the rear brakes or
if the brakes are wet. When there is
the risk that your parking brake may
freeze, temporarily apply it with the
VKLIWOHYHULQ1 IRU$XWRPDWHG0DQXDO
Transmission) or in first or reverse
gear (for manual transmission). Also,
block the rear wheels in advance, so
the vehicle may not roll. Then, release
the parking brake.Do not let ice and snow
accumulate underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driv-
ing in such conditions during the
severe winter, you should check
underneath the vehicle on a regular
basis, to ensure that the front wheels
and the steering components is
unblocked.
Carry emergency equipment
In accordance with weather condi-
tions, you should carry appropriate
emergency equipment, whilst driving.
Some of the items you may want to
carry include tyre chains, tow straps
or chains, flashlight, emergency
IODUHV VDQG VKRYHO MXPSHU FDEOHV
window scraper, gloves, ground cloth,
coveralls, blanket, etc.
Do not place objects or materials
in the engine compartment
3XWWLQJ REMHFWV RU PDWHULDOV LQ WKH
engine compartment may cause an
engine failure or combustion,
because they may block the engine
cooling. Such damage will not be
covered by the manufacturer’s war-
ranty.

Page 359 of 486

7-7
07
i,QIRUPDWLRQ
3E
An inappropriately disposed
battery can be harmful to the
environment and human
health. Dispose of the battery
according to your local law(s)
or regulations.
Jump starting procedure
1. Position the vehicles close enough
that the jumper cables will reach,
but do not allow the vehicles to
touch.
2. Avoid fans or any moving parts in
the engine compartment at all
times, even when the vehicles are
turned off.
3. Turn off all electrical devices such
as radios, lights, air conditioning,
etc. Put the vehicles in N (Neutral,
for Automated manual transmis-
sion vehicle) or neutral (for Manual
transmission vehicle), and set the
parking brakes. Turn both vehicles
OFF.
OAC3079002TU
4. Connect the jumper cables in the
exact sequence shown in the illus-
tration. First connect one jumper
cable to the red, positive (+) jump-
er terminal of your vehicle (1).
5. Connect the other end of the jump-
er cable to the red, positive (+) bat-
tery/jumper terminal of the assist-
ing vehicle (2).
6. Connect the second jumper cable
to the black, negative (-) battery/
chassis ground of the assisting
vehicle (3).
7. Connect the other end of the sec-
ond jumper cable to the black, neg-
ative (-) chassis ground of your
vehicle (4).
Do not allow the jumper cables to
contact anything except the correct
battery or jumper terminals or the
correct ground. Do not lean over
the battery when making connec-
tions.

Page 446 of 486

8-50
Maintenance
&RQVXOW D +<81'$, DXWKRULVHG UH-
SDLUHU WR UHSODFH PRVW YHKLFOH OLJKW
EXOEV ,W LV GLIILFXOW WR UHSODFH YHKLFOH
OLJKWEXOEVEHFDXVHRWKHUSDUWVRIWKH
YHKLFOH PXVW EH UHPRYHG EHIRUH \RX
FDQJHWWRWKHEXOE7KLVLVHVSHFLDOO\
WUXH IRU UHPRYLQJ WKH KHDGOLJKW DV-
VHPEO\WRJHWWRWKHEXOE V 
5HPRYLQJLQVWDOOLQJWKHKHDGOLJKWDV-
VHPEO\ FDQ UHVXOW LQ GDPDJH WR WKH
vehicle.
WARNING
Prior to replacing a light, depress
the foot brake, move the shift lever
into the N (Neutral, for Automated
manual transmission vehicle) or
neutral (for manual transmission
vehicle), apply the parking brake,
place the ignition switch in the
LOCK/OFF position, and take the
key with you when leaving the ve-
hicle to avoid sudden movement
of the vehicle and to prevent pos-
sible electric shock.
Be aware the bulbs may be hot and
may burn your fingers.
NOTICE
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause
damage to the fuse or electric wir-
ing system.
i Information
The headlight and tail lamp lenses
could appear frosty if the vehicle is
washed after driving or the vehicle is
driven at night in wet weather. This
condition is caused by temperature dif-
ference between the lamp inside and
outside and, it does not indicate a
problem with your vehicle. When
moisture condenses in the lamp, it will
be removed after driving with the
headlight on. The removable level may
differ depending on lamp size, lamp
position and environmental condition.
However, if moisture is not removed,
we recommend that your vehicle is in-
spected by a HYUNDAI authorised re-
pairer.
i Information (For Europe)
Traffic Change
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direction,
this asymmetric part will dazzle on-
coming car driver. To prevent dazzle,
ECE regulation demand several tech-
nical solutions (ex. automatic change
system, adhesive sheet, down aiming).
These headlights are designed not to
dazzle opposite drivers. So, you need
not change your headlights in a coun-
try with opposite traffic direction.
LIGHT BULBS

Page:   < prev 1-10 11-20