weight HYUNDAI I10 2021 Owners Manual

1-6
Foreword
Vehicle damage or driveability prob-
lems may not be covered by the man-
ufacturer’s warranty if they result from
the use of:
1. Gasohol containing more than
10% ethanol.
2. Petrol or gasohol containing meth-
anol.
3. Leaded fuel or leaded gasohol.
CAUTION
Never use gasohol which contains
methanol. Discontinue use of any
gasohol product which impairs
drivability.
Other fuels
Using fuel additives such as:
- Silicone fuel additive
- MMT (Magnanese, Mn) fuel addi-
tive
- Ferrocene (iron-based) fuel addi-
tive
- Other metallic-based fuel additives
may result in cylinder misfire, poor
acceleration, engine stalling, damage
to the catalyst, or abnormal corro-
sion, and may cause damage to the
engine resulting in a reduction in the
overall life of the powertrain.
NOTICE
Damage to the fuel system or per-
formance problem caused by the
use of these fuels may not be cov-
ered by your New Vehicle Limited
Warranty.
Use of MTBE
HYUNDAI recommends avoiding
fuels containing MTBE (Methyl
Tertiary Butyl Ether) over 15.0% vol.
(Oxygen Content 2.7% weight) in
your vehicle.
Fuel containing MTBE over 15.0%
vol. (Oxygen Content 2.7% weight)
may reduce vehicle performance and
produce vapour lock or hard starting.
CAUTION
Your New Vehicle Limited Warranty
may not cover damage to the fuel
system and any performance prob-
lems that are caused by the use of
fuels containing methanol or fuels
containing MTBE (Methyl Tertiary
Butyl Ether) over 15.0% vol.
(Oxygen Content 2.7% weight.)
Do not use methanol
Fuels containing methanol (wood
alcohol) should not be used in your
vehicle. This type of fuel can reduce
vehicle performance and damage
components of the fuel system,
engine control system and emission
control system.

Exterior overview (I)............................................................................................ 2-2
Exterior overview (II) .......................................................................................... 2-3
Interior overview ................................................................................................. 2-4
Instrument panel overview ................................................................................ 2-5
Engine compartment ......................................................................................... 2-7
Dimensions .........................................................................................................2-8
Engine specification ...........................................................................................2-8
Bulb wattage .......................................................................................................2-9
Tyres and wheels............................................................................................... 2-10
Air conditioning system..................................................................................... 2-11
Tyre load and speed capacity ........................................................................... 2-11
Gross vehicle weight ......................................................................................... 2-11
Luggage volume ................................................................................................ 2-11
Recommended lubricants and capacities .......................................................2-12
Recommended SAE viscosity number .........................................................2-13
Vehicle identification number (VIN) .................................................................2-14
Vehicle certification label ..................................................................................2-14
Tyre specification and pressure label ...............................................................2-15
Engine number ..................................................................................................2-15
Air conditioner compressor label .................................................................... 2-16
Fuel label ........................................................................................................... 2-16
Declaration of conformity ................................................................................. 2-17
2. Vehicle information
2

2-11
02
AIR CONDITIONING SYSTEM
ItemWeight of Volume Classification
Refrigerant oz. (g)15.17±0.88 (430±25)R-134a
R-1234yf
Compressor lubricant oz. (g)3.53 (100) PAG
Contact a HYUNDAI authorised repairer for more details.
lbs. (kg)
TYRE LOAD AND SPEED CAPACITY
ItemTyre sizeWheel
sizeLoad Capacity Speed Capacity
LI *1kg SS *2PSKNPK
Full size tyre175/65R14 5.5JX14 86 530 T 118 (190)
185/55R15 6.0JX15 86 530 H 130 (210)
195/45R16 6.5JX16 84 500 H 130 (210)
Temporary
tyreT115/70D15 3.5JX15 90 600 M 81 (130)
LUGGAGE VOLUMEGROSS VEHICLE WEIGHT
*1 LI : LOAD INDEX *2 SS : SPEED SYMBOL
ItemsPetrol Engine
1.0 MPI 1.2 MPI
VDA
l (cu ft)MIN. 252 (8.90)
MAX. 1,050 (37.08)
Min : Behind rear seat to upper edge of the seat back.
Max : Behind front seat to roof.
6HDWHU5 Seater
1.0 MPI 1.2 MPI 1.0 MPI 1.2 MPI
AMT MTMT
(ECO)AMT MT AMT MT AMT MT
2,954
(1,340)2,954
(1,340)2,888
(1,310)2,976
(1,350)2,976
(1,350)3,108
(1,410)3,108
(1,410)3,152
(1,430)3,152
(1,430)

3-27
03
Seat belt use and children
Infant and small children
Most countries have child restraint
laws which require children to travel
in approved child restraint devices,
including booster seats. The age at
which seat belts can be used instead
of child restraints differs among coun-
tries, so you should be aware of the
specific requirements in your country,
and where you are travelling. Infant
and child restraints must be properly
placed and installed in a rear seat.
For more details, refer to the “Child
Restraint Systems” in this chapter.
WARNING
ALWAYS properly restrain infants
and small children in a child restraint
appropriate for the child’s height
and weight.
To reduce the risk of serious injury
or death to a child and other passen-
gers, NEVER hold a child in your lap
or arms when the vehicle is moving.
The violent forces created during an
accident will tear the child from your
arms and throw the child against the
interior of the vehicle.
Small children are best protected
from injury in an accident when prop-
erly restrained in the rear seat by a
child restraint system that meets the
requirements of the Safety Standards
of your country. Before buying any
child restraint system, make sure that
it has a label certifying that it meets
Safety Standard of your country. The
restraint must be appropriate for your
child’s height and weight. Check the
label on the child restraint for this
information. Refer to “Child Restraint
Systems” in this chapter.
Larger children
Children under age 13 and who are
too large for a booster seat must
always occupy the rear seat and use
the available lap/shoulder belts. A
seat belt should lie across the upper
thighs and be snug across the shoul-
der and chest to restrain the child
safely. Check belt fit periodically. A
child’s squirming could put the belt
out of position. Children are afforded
the most safety in the event of an
accident when they are restrained by
a proper restraint system and/or seat
belts in the rear seat.
If a larger child over age 13 must be
seated in the front seat, the child
must be securely restrained by the
available lap/shoulder belt and the
seat should be placed in the rearmost
position.
If the shoulder belt portion slightly
touches the child’s neck or face, try
placing the child closer to the centre
of the vehicle. If the shoulder belt still
touches their face or neck, they need
to be returned to an appropriate
booster seat in the rear seat.
WARNING
‡Always make sure larger chil-
dren’s seat belts are worn and
properly adjusted.
‡NEVER allow the shoulder belt to
contact the child’s neck or face.
‡Do not allow more than one child
to use a single seat belt.

3-29
03
CHILD RESTRAINT SYSTEM
ãCRS
ä
Our recommendation:
Children always in the rear
WARNING
Always properly restrain children
in the rear seats of the vehicle,
unless the air bag on the front pas-
senger seat is deactivated.
Children of all ages are safer when
restrained in the rear seat. A child
riding in the front passenger seat
can be forcefully struck by an
inflating air bag resulting in
SERIOUS INJURY or DEATH.
Children under age 13 must always
ride in the rear seats and must always
be properly restrained to minimise
the risk of injury in an accident, sud-
den stop or sudden manoeuvre.
According to accident statistics, chil-
dren are safer when properly
restrained in the rear seats than in
the front seat. Children too large for a
Child Restraint System must use the
seat belts provided.
Most countries have Child Restraint
Systems which require children to
travel in approved Child Restraint
Systems. The laws governing the age
or height/weight restrictions at which
seat belts can be used instead of
Child Restraint System differs among
countries, so you should be aware of
the specific requirements in your
country, and where you are travelling.Child Restraint Systems must be
properly placed and installed in the
rear seat. You must use a commer-
cially available Child Restraint
System that meets the requirements
of the Safety Standards of your coun-
try.
Child Restraint Systems are general-
ly designed to be secured in a vehicle
seat by lap belt or the lap belt portion
of a lap/shoulder belt, or by a top-
tether and/or ISOFIX anchorage in
the rear seats of the vehicle.
Child Restraint System (CRS)
always in the rear
Infants and younger children must be
restrained in an appropriate rear-
ward-facing or forward-facing CRS
that has first been properly secured
to the rear seat of the vehicle. Read
and comply with the instructions for
installation and use provided by the
manufacturer of the Child Restraint
System.
WARNING
‡Always follow the Child Restraint
System manufacturer’s instruc-
tions for installation and use.
‡Always properly restrain your
child in the Child Restraint
System.
‡Do not use an infant carrier or a
child safety seat that “hooks”
over a seatback, it may not pro-
vide adequate protection in an
accident.
‡After an accident, we recom-
mend a HYUNDAI dealer check
the Child Restraint System, seat
belts, ISOFIX anchorages and
top-tether anchorages.

3-30
Safety system
Selecting a Child Restraint
System (CRS)
When selecting a CRS for your child,
always:
‡Make sure the CRS has a label cer-
tifying that it meets applicable
Safety Standards of your country.
‡Select a Child Restraint System
based on your child’s height and
weight. The required label or the
instructions for use typically provide
this information.
‡Select a Child Restraint System
that fits the vehicle seating position
where it will be used.
‡Read and comply with the warnings
and instructions for installation and
use provided with the Child
Restraint System.
Child Restraint System types
There are three main types of Child
Restraint Systems: rearward-facing
seats, forward-facing seats, and
booster seats. They are classified
according to the child’s age, height
and weight.
CRS09
Rearward-facing Child Restraint
System
A rearward-facing Child Restraint
System provides restraint with the
seating surface against the back of
the child. The harness system holds
the child in place, and in an accident,
acts to keep the child positioned in
the Child Restraint Systems and
reduce the stress to the fragile neck
and spinal cord.
All children under the age of one year
must always ride in a rearward-facing
Child Restraint System. There are
different types of rearward-facing
Child Restraint Systems: infant-only
Child Restraint Systems can only be
used rearward-facing. Convertible
and 3-in-1 Child Restraint Systems
typically have higher height and
weight limits for the rearward-facing
position, allowing you to keep your
child rearward-facing for a longer
period of time.
Keep using Child Restraint Systems
in the rearward-facing position as
long as children fit within the height
and weight limits allowed by the Child
Restraint System’s manufacturer.

3-31
03
OIB034017
Forward-facing Child Restraint
System
A forward-facing Child Restraint
System provides restraint for the
child’s body with a harness. Keep
children in a forward-facing Child
Restraint System with a harness until
they reach the top height or weight
limit allowed by your Child Restraint
System’s manufacturer.
Once your child outgrows the for-
ward-facing Child Restraint System,
your child is ready for a booster seat.
Booster seats
A booster seat is Child Restraint
System designed to improve the fit of
the vehicle’s seat belt system. A
booster seat positions the seat belt
so that it fits properly over the stron-
ger parts of your child’s body. Keep
your children in booster seats until
they are big enough to fit in a seat
belt properly.
For a seat belt to fit properly, the lap
belt must lie comfortable across the
upper thighs, not the stomach. The
shoulder belt should lie comfortable
across the shoulder and chest and
not across the neck or face. Children
under age 13 must always be prop-
erly restrained to minimise the risk of
injury in an accident, sudden stop or
sudden manoeuvre.
Installing a Child Restraint
System (CRS)
WARNING
Before installing your Child
Restraint System always:
Read and follow the instructions
provided by the manufacturer of
the Child Restraint System.
Failure to follow all warnings and
instructions could increase the
risk of the SERIOUS INJURY or
DEATH if an accident occurs.
WARNING
If the vehicle head restraint pre-
vents proper installation of a Child
Restraint System, the head
restraint of the respective seating
position shall be readjusted or
entirely removed.
After selecting a proper Child
Restraint System and checking that
the Child Restraint System fits prop-
erly in the rear of this vehicle, you are
ready to install the Child Restraint
System according to the manufactur-
er’s instruction. There are three gen-
eral steps in installing the Child
Restraint Systems properly:
‡Properly secure the Child
Restraint System to the vehicle.
All Child Restraint System must be
secured to the vehicle with the lap
belt or lap part of a lap/shoulder belt
or with the ISOFIX top-tether and/or
ISOFIX anchorage.

3-37
03
Note 1) : The universal belted CRS applies to all mass groups.
Note 2) : Seating position not suitable for child restraint system if the passenger’s front
air bag is activate.
Note
3) : To install a ISOFIX Child Restraint Systems :
- Driver Seat : You should move the seat at mid position and adjust the height
of seat to highest and head restraint stay angle to 9° position.
- Front Passenger Seat : You should move the seat at foremost and head
restraint stay angle to 9° position.
Note
4) : To install a ISOFIX Child Restraint Systems:
You should remove the head restraint of the seat.
Note
5) : The seating position (number 5) is not suitable for fitment of child restraint sys-
tem with support leg.
K Do not use forward facing child restraint system when child’s weight is below 13 kg at
all seat.
K For semi-universal or vehicle specific CRS(ISOFIX or belted CRS), please see the
vehicle list provided in the manual of CRS.
Seat
NumberPosition
in the vehicle
1 Front right
2 Front centre
3 Front left
42
nd row right
5* 2
nd row centre
62
nd row left
* : 5 Seater, if equippedOOSEV038035R
Recommended Child Restraint Systems (for Europe)
Mass
groupName Manufacturer Type of FixationECE-R44/R129
Approval No.
Group 0+Cabriofix &
FamilyfixMaxi Cosi ISOFIX E4 04443907
Group I Duo Plus Britax Römer ISOFIX and top-tether E1 04301133
Group II KidFix II XP Britax RömerForward-facing with ISOFIX
and vehicle beltE1 04301323
Group III Junior III GracoForward-facing with vehicle
beltE11 03.44.164
E11 03.44.165
CRS Manufacturer information
Maxi Cosi Cabriofix & Familyfix http://www.maxi-cosi.com
Britax Römmer http://www.britax.com
Graco http//www.gracobaby.com

5-43
05
NOTICE
If the driver exits the vehicle
through another door besides the
driver door, the battery saver func-
tion does not operate and the
headlight delay function does not
WXUQ2))DXWRPDWLFDOO\
This may cause the battery to dis-
charge. To avoid battery dis-
FKDUJH WXUQ 2)) WKH KHDGOLJKWV
manually from the headlight switch
before exiting the vehicle.
Daytime running light (DRL)
(if equipped)
The Daytime Running Lights (DRL)
can make it easier for others to see
the front of your vehicle during the
day, especially after dawn and before
sunset.
The DRL system will turn the dedi-
cated light OFF when:
1. The parking brake is applied.
2. The engine is turned off.
Headlight levelling device
OAC3059028R
7R DGMXVW WKH KHDGOLJKW EHDP OHYHO
according to the number of the pas-
sengers and loading weight in the
luggage area, turn the beam levelling
switch.
The higher the number on the switch
position, the lower the headlight
beam level. Always keep the head-
light beam at the proper levelling
position, or headlights may dazzle
other road users.
/LVWHG EHORZ DUH H[DPSOHV RI DSSUR-
priate switch settings for varying
loads. For loading conditions other
WKDQ WKRVH OLVWHG DGMXVW WKH VZLWFK
position to the most similar situation.
Loading conditionSwitch position
Driver only0
Driver + Front pas-
senger0
Full passengers
(including driver)1
Full passengers
(including driver) +
0D[LPXPSHUPLVVLEOH
loading2
'ULYHU0D[LPXP
permissible loading 3

6
6. Whilst driving
Special driving conditions ............................................................................... 6-88
Hazardous driving conditions...................................................................... 6-88
Rocking the vehicle ................................................................................... 6-88
Smooth cornering ........................................................................................ 6-89
Driving at night ............................................................................................. 6-89
Driving in the rain ......................................................................................... 6-89
Driving in flooded areas ............................................................................... 6-90
Highway driving ............................................................................................ 6-90
Winter driving
................................................................................................... 6-91
Snow or icy conditions .................................................................................. 6-91
Winter Precautions ....................................................................................... 6-93
Vehicle weight
.................................................................................................. 6-95
Overloading .................................................................................................. 6-95
Trailer towing
................................................................................................... 6-96