HYUNDAI I20 2017 Owners Manual

1.$&
,204/3424-3
FFuse Name
Symbol
Fuse rating
Circuit Protected
Multi Fuse
MDPS
1
80A
MDPS Unit
ALT
[125A]
(150A)
Alternator, Fuse - F8 / F9 / F10 / F11
Fuse
ECU 4
[15A]
ECM/PCM
B+3
30A
I/P Junction Block (Power Connector (Fuse - F45, F46), Fuse - F 5, F9, F34)
IG1
30A
W/O Button Start : Ignition Switch
With Button Start : PDM Relay Box (IG1 / ACC Relay)
B+1
30A
I/P Junction Block (Fuse - F11, F12, F20, F23, F24)
GLOW
(80A)
E/R Junction Block (RLY. 1)
B+5
40A
I/P Junction Block (P/OUTLET Relay)
B+4
40A
I/P Junction Block (Fuse - F6)
ABS
30A
ABS Control Module
ABS
40A
ABS Control Module, Multipurpose Check Connector
Engine compartment main fuse panel[ ] : G4LA (Gasoline 1.2)
( ) : D4FC (Diesel 1.4)

1.$%,204/3424-3[ ] : MFR (Multi Focus Reflector) Headlight
( ) : Bi-Function Projection HeadlightPCB Block (Gasoline engine)FF use Name
Symbol
Fuse rating
Circuit Protected
ECU 1
30A
PCB Block (Engine Control Relay, Fuse - F25)
HORN
15A
Horn Relay, B/Alarm Horn Relay
FUEL PUMP
20A
F/Pump Relay
WIPER FRT
25A
Wiper Lo Relay
DRL
(10A)
DRL Relay
H/LAMP LO
20A
H/Lamp Lo Relay
H/LAMP HI
[20A] (10A)
H/Lamp Hi Relay
C/FAN
40A
C/Fan Lo Relay, C/Fan Hi Relay
BLOWER
50A
Blower Relay
IG 2
30A
Start Relay, W/O Button Start : Ignition Switch, With Button St art : PDM Relay Box (IG2 Relay)
B+2
30A
I/P Junction Block (P/WDW Relay, TAIL Relay, Fuse - F1)
TCU 1
10A
1.2 CVT : PCM
ECU 3
15A
F/Pump Relay, ECM, C/Fan HI/LO Relay, Camshaft Position Sensor #1/#2, Oxygen Sensor
(Up/Down), Oil Control Valve #1/#2, Purge Control Solenoid Valve, Variable Intake Solenoid
Valve, A/CON Relay, Immobilizer Module
B/UP LAMP
B/UP
LAMP
10A
CVT : PCM, Transaxle Range Switch, Instrument Cluster, Audio
M/T : Back-Up Lamp Switch, I/P Junction Block (Fuse - F26)

1.$+
,204/3424-3
PCB Block (Gasoline engine)FFuse Name
Symbol
Fuse rating
Circuit Protected
H/LAMP RH
10A
Head Lamp RH
H/LAMP LH
10A
Head Lamp LH
TCU 2
15A
1.4 A/T : PCM
ECU 2
15A
ECM/PCM, Injector #1/#2/#3#4
IGN COIL
15A
Ignition Coil #1/#2/#3/#4, Condenser

1.$),204/3424-3PCB Block (Diesel engine)FFuse Name
Symbol
Fuse rating
Circuit Protected
ECU 1
30A
PCB Block (Engine Control Relay)
HORN
15A
Horn Relay, B/Alarm Horn Relay
WIPER FRT
25A
Wiper Lo Relay
DRL
(10A)
DRL Relay
H/LAMP LO
20A
H/Lamp Lo Relay
H/LAMP HI
[20A] (10A)
H/Lamp Hi Relay
C/FAN
50A
C/Fan Lo Relay, C/Fan Hi Relay
BLOWER
50A
Blower Relay
IG 2
30A
Start Relay, W/O Button Start : Ignition Switch, With Button St art : PDM Relay Box (IG2 Relay)
B+2
30A
I/P Junction Block (P/WDW Relay, TAIL Relay, Fuse : F1)
ECU 3
10A
Stop Lamp Switch, C/FAN Lo/Hi Relay, A/CON Relay
B/UP LAMP
B/UP
LAMP
10A
Back-Up Lamp Switch, I/P Junction Block (Fuse - F26)
H/LAMP RH
10A
Head Lamp RH
H/LAMP LH
10A
Head Lamp LH
[ ] : MFR (Multi Focus Reflector) Headlight
( ) : Bi-Function Projection Headlight

1.$(
,204/3424-3
PCB Block (Diesel engine)FFuse Name
Symbol
Fuse rating
Circuit Protected
ECU 4
20A
ECM
ECU 2
15A
E/R Junction Block (RLY. 1), Electrical EGR Control Valve, Mass Air Flow Sensor,
WGT Control Solenoid Valve, Camshaft Position Sensor, Immobilizer Module
ECU 5
10A
Fuel Pressure Regulator Valve

1.$#,204/3424-3!#Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlight
assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to
the vehicle.
Information
After heavy driving, rain or washing
headlight and taillight lenses could
appear frosty. This condition is caused
by the temperature difference
between the lamp inside and outside.
This is similar to the condensation on
your windows inside your vehicle dur-
ing the rain and doesn’t indicate a
problem with your vehicle. If the
water leaks into the lamp bulb circuit-
ry, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause dam -
age to the fuse or electric wiring sys-
tem.
i
Prior to replacing a light, depress
the foot brake, move the shift lever
into the P (Park, for Continuo usly
Variable Transaxle vehicle) or
neutral (for Manual Transaxle
vehicle), apply the parking brake,
plac e the ignition switch in the
LOCK/OFF position, and take the
key with you when leaving the
vehicle to av oid sudden move-
ment of the vehicle and to prevent
possible electric shock.
Be aware the bulbs may be h ot
and may burn your fingers.
WARNING

1.$$
,204/3424-3
HHeadlight, Parking (Position)
Light, Turn signal Light, Low
Beam Assist-Static Light, Fog
Light and Daytime Running Light
bulb replacement(1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Daytime Running Light
(if equipped)
(5) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector) Headlight (1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight (1) Headlight (Low/High) *
1
(2) Parking (Position) Light
(3) Front Turn signal Light
(4) Front Fog Light (if equipped)
*1: MFR (Multi Focus Reflector)
Headlight
OIB077068
■ 5 Door
• Type A
OIB077069
■5 Door
• Type B
OIB077070
■Cross
• Type A

1.$',204/3424-3
(1) Headlight (Low/High) *
2
(2) Low Beam Assist-Static Light
(3) Front Turn Signal Light
(4) Position Light/ Daytime Running Light (DRL)
(5) Front Fog Light (if equipped)
*2: Bi-Function Projection Headlight
II nformation
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, consult an
authorized HYUNDAI dealer.
The Fog Light aiming adjustment can be done by removing UNDER
COVER. Consult an authorised
HYUNDAI dealer.i(Continued)•
Always handle them carefully,
and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact w ith liquids. Never touch
the glass with bare hands.
Residual oil may cause the bulb
to overheat and burs t when lit. A
bulb should be operated only
when installed in a headlight.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
•
Wear eye protection when
changing a bulb. Allow the bulb
to cool down before handling it.
Halogen bulbs•
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
(Continued)
WARNING
OLMB073042L
OIB077060
■Cross
• Type B

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

1.',204/3424-3LLow Beam Assist-Static Light1. Open the hood.
2. Remove the Low Beam Assist-
Static Light bulb cover by turning it
counterclockwise.
3. Disconnect the Low Beam Assist- Static Light bulb socket-connector.
4. Unsnap the Low Beam Assist- Static Light bulb retaining wire by
depressing the end and pushing it
upward.
5. Remove the bulb from the Low Beam Assist-Static Light assem-
bly. 6. Install a new Low Beam Assist-
Static Light bulb and snap the Low
Beam Assist-Static Light bulb
retaining wire into position by
aligning the wire with the groove
on the bulb.
7. Connect the Low Beam Assist- Static Light bulb socket connector.
8. Install the Low Beam Assist-Static Light bulb cover by turning it clock-
wise.
Parking (Position) light1. Remove the socket from theassembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light or Daytime runninglight (if equipped)
OIB075061
Low Beam Assist-Static Light
OIB077071OIB077072OIB077073
■
5 Door
• Type A (without DRL)■5 Door
• Type A (with DRL)■ Cross