warning light HYUNDAI I20 2017 Workshop Manual

Page 280 of 400

+)
!-0,0*&."'$-.,/#0%(/
"'(%!
#(V(&
 &($( &"
Hazardous driving conditions
When hazardous driving conditions
are encountered such as water\b
snow\b ice\b mud or sand:
Drive cautiously and allow extra dis
tance for braking.
Avoid sudden movements in braking
or steering.
If stuck in snow\b mud\b or sand\b use
second gear. Accelerate slowly to
avoid spinning the drive wheels.
Use sand\b rock salt\b or other nonslip
material under the drive wheels to
provide traction when stalled in ice\b
snow\b or mud.
Rocking the vehicle
If it is necessary to rock the vehicle
to free it from snow\b sand\b or mud\b
first turn the steering wheel right and
left to clear the area around your
front wheels. Then\b shift back and
forth between 1st and R (Reverse\b
for Manual Transaxle vehicle) or R
(Reverse) and a forward gear (for
Automatic Transaxle/Continuously
Variable Transaxle vehicle). Try to
avoid spinning the wheels\b and do
not race the engine.
To prevent transaxle wear\b wait until
the wheels stop spinning before
shifting gears. Release the accelera
tor pedal while shifting\b and press
lightly on the accelerator pedal while
the transaxle is in gear. Slowly spin
ning the wheels in forward and
reverse directions causes a rocking
motion that may free the vehicle. If the tires spin at high speed the
tires can explode\b and you or others
may be injured. Do not attempt this
procedure if people or objects are
anywhere near the vehicle.
The vehicle can overheat causing an
engine compartment fire or other
damage. Spin the wheels as little as
possible and avoid spinning the
wheels at speeds over 5
6 k
m/h (35
mph) as indicated on the speedome
ter.
If you are still stuck after rocking the
vehicle a few times\b have the vehicle
pulled out by a tow vehicle to avoid
engine overheating\b possible dam
age to the transaxle\b and tire dam
age. See “Towing” in chapter 6.
NOTICE
NOTICE
Downshifting with an Automatic
Transaxle/ Continuously Variable
Transaxle\b while driving on slippery
surfaces can cause an accident.
The sudden change in tire speed
could cause the tires to skid. Be
careful when downshifting on slip
pery surfaces.
WARNING

Page 283 of 400

Snow or icy conditions
You need to keep sufficient distance
between your vehicle and the vehicle
in front of you.
Apply the brakes gently. Speeding\b
rapid acceleration\b sudden brake
applications\b and sharp turns are
potentially very hazardous practices.
During deceleration\b use engine
braking to the fullest extent. Sudden
brake applications on snowy or icy
roads may cause skids to occur.
To drive your vehicle in deep snow\b it
may be necessary to use snow tires
or to install tire chains on your tires.
Always carry emergency equipment.
Some of the items you may want to
carry include tire chains\b tow straps
or chains\b a flashlight\b emergency
flares\b sand\b a shovel\b jumper cables\b
a window scraper\b gloves\b ground
cloth\b coveralls\b a blanket\b etc.
Snow tires
If you mount snow tires on your vehi
cle\b make sure to use radial tires of
the same size and load range as the
original tires. Mount snow tires on all
four wheels to balance your vehicle’s
handling in all weather conditions.
The traction provided by snow tires
on dry roads may not be as high as
your vehicle's original equipmenttires. Check with the tire dealer for
maximum speed recommendations.
Information
Do not install studded tires without
first checking local and municipal reg
ulations for possible restrictions
against their use\b
i
W(&$'#
#(V(&
Snow tires should be equivalent in
size and type to the vehicle's stan
dard tires. Otherwise\b the safety
and handling of your vehicle may
be adversely affected.
WARNING

!-0,0*&."'$-.,/#0%(/
+)+

Page 289 of 400

The hazard warning flasher serves
as a warning to other drivers to exer-
cise extreme caution when
approaching, overtaking, or passing
your vehicle.
It should be used whenever emer-
gency repairs are being made or
when the vehicle is stopped near the
edge of a roadway.
To turn the hazard warning flasher
on or off, press the hazard warning
flasher button with the ignition switch
in any position. The button is located
in the center console switch panel. All turn signal lights will flash simul-
taneously.
• The hazard warning flasher oper-
ates whether your vehicle is run-
ning or not.
• The turn signals do not work when the hazard flasher is on."" " #$#"% !$#'#"'"' %'$%'&&&%
OIB067001

Page 291 of 400

$$!%%#$#%$#!!" !If the engine doesn't turn over or
turns over slowly • Be sure the shift lever is in N
(Neutral) or P (Park) if it is a
Continuously Variable Transaxle
vehicle. The engine starts only
when the shift lever is in N
(Neutral) or P (Park).
• Check the battery connections to be sure they are clean and tight.
• Turn on the interior light. If the light dims or goes out when you operate
the starter, the battery is drained.
Do not push or pull the vehicle to
start it. This could cause damage to
your vehicle. See instructions for "Jump Starting"
provided in this chapter.
If the engine turns over normally but doesn't start • Check the fuel level and add fuel if
necessary.
If the engine still does not start, we
recommend that you call an author-
ized HYUNDAI dealer for assistance.
! $#'#"'"' %'$%'&&&%Push or pull starting the vehicle
may cause the catalytic converter
to overload which can lead to
damage to the emission control
system.
WARNING

Page 315 of 400

"$# !"$" "$#The following lists are vehicle checks
and inspections that should be per-
formed at the frequencies indicated
to help ensure safe, dependable
operation of your vehicle.
Any adverse conditions should be
brought to the attention of your deal-
er as soon as possible.
These Owner Maintenance Checks
are generally not covered by war-
ranties and you may be charged for
labor, parts and lubricants used.
Owner maintenance schedule When you stop for fuel:• Check the engine oil level.
• Check the coolant level in coolant
reservoir.
• Check the windshield washer fluid level.
• Look for low or under-inflated tires.
• Check the radiator and condenser. Check if the front of the radiator
and condenser are clean and not
blocked with leaves, dirt or insects
etc.
If any of the above parts areextremely dirty or you are not sure
of their condition, we recommend
that you contact an authorized
HYUNDAI dealer.
While operating your vehicle:• Note any changes in the sound of the exhaust or any smell of
exhaust fumes in the vehicle.
• Check for vibrations in the steering wheel. Notice any increased steer-
ing effort or looseness in the steer-
ing wheel, or change in its straight-
ahead position.
• Notice if your vehicle constantly turns slightly or "pulls" to one side
when traveling on smooth, level
road.
• When stopping, listen and check for unusual sounds, pulling to one
side, increased brake pedal travel
or "hard-to-push" brake pedal.
• If any slipping or changes in the operation of your transaxle occurs,
check the transaxle fluid level.
• Check Continuously Variable Transaxle P (Park) function.
• Check the parking brake.
• Check for fluid leaks under your vehicle (water dripping from the air
conditioning system during or after
use is normal).
1.',204/3424-3
Be careful when checking your
engine coolant level when the
engine is hot. Scalding hot coolant
and stea m may blow out under
pressure. This could cause burns
or other serious injury.
WARNING

Page 316 of 400

AAt least monthly:• Check the coolant level in theengine coolant reservoir.
• Check the operation of all exterior lights, including the stoplights, turn
signals and hazard warning flash-
ers.
• Check the inflation pressures of all tires including the spare for tires
that are worn, show uneven wear,
or are damaged.
• Check for loose wheel lug nuts.
At least twice a year (i.e., every Spring and Fall):• Check the radiator, heater and air
conditioning hoses for leaks or
damage.
• Check the windshield washer spray and wiper operation. Clean
wiper blades with clean cloth
dampened with washer fluid.
• Check the headlight alignment.
• Check the muffler, exhaust pipes, shields and clamps.
• Check the lap/shoulder belts for wear and function.
At least once a year:• Clean the body and door drainholes.
• Lubricate the door hinges and checks, and hood hinges.
• Lubricate the door and hood locks and latches.
• Lubricate the door rubber weather- strips.
• Check the air conditioning system.
• Inspect and lubricate Continuously Variable Transaxle linkage and
controls.
• Clean the battery and terminals.
• Check the brake/clutch fluid level.
1.1
,204/3424-3

Page 339 of 400

1.+',204/3424-3$#!$#
#!$$Draining water from fuel filterThe fuel filter for diesel engine plays
an important role of separating water
from fuel and accumulating the water
in its bottom.
If water accumulates in the fuel filter,
the warning light comes on when the
ignition switch is in the ON position.
If this warning light turned
on, we recommend that
the system be serviced by
an authorized HYUNDAI
dealer.If the water accumulated in the fuel
filter is not drained at proper times,
damages to the major parts such as
the fuel system can be caused by water permeation in the fuel filter.
Extracting air from the fuel filterIf you drive until you have no fuel left
or if you replace the fuel filter, be
sure to extract air from the fuel sys-
tem as it makes it difficult to start the
engine.
1. Pump up and down(1) approxi- mately 50 times until the pump is
hard.
2. Extract air from the fuel filter by removing the bolt(2) with a cross-
tip screw driver and reinstall the
bolt(2).
3. Pump up and down(1) approxi- mately 15 times.
4. Extract air from the fuel filter by removing the bolt(2) with a cross-
tip screw driver and reinstall the
bolt(2).
5. Pump up and down(1) approxi- mately 5 times.
Information
Use cloths when you extract air sothat the fuel is not sprayed around.
Clean the fuel around the fuel filter or the injection pump before start-
ing the engine to prevent fire.
Finally, check each part if the fuel is leaking.i
NOTICE
OIB074016

Page 346 of 400

1.)#,204/3424-3
(Continued)If any electrolyte gets
into your eyes, flush
your eyes with clean
water for at least 15
minut es and get imme-
diate medical attention.
If electrolyte gets on
your skin, thoroughly
wash the contacted
area. If you feel a pain
or a burning sensation,
get medical attention
immediately.
Wear eye protection
wh en charging or work-
ing near a battery.
Always provide ventila-
tion when working in an
enclosed space.
(Continued)
(Continued)
An inappropriately dis-
posed battery can be
harmful to the environ-
ment and human
health. Di spose the
battery according to
your local law(s) or reg-
ulation.
The battery contains
lead. Do not dispos e of
it after use. Please
return the battery to an
authorized HYUNDAI
dealer to be recycled.•
When lifting a plastic-cased bat-
tery, excessive pressure on the
case may cause battery acid to
leak, r esulting in personal injury.
Lift with a battery carrier or with
your hands on opposite corners.
(Continued)
Battery dangers
Always read the follow-ing instructions careful-
ly when handling a bat-
tery.
Keep light ed cigarettes
and all other flames or
sparks away from the
battery.
Hydrogen, a highly combustible gas, i s
always present in bat-
tery cells and may
explode if ignited.
Keep batteries out of the reach of children
because batteries con-
tain highly corrosive
SULFURIC ACID. Do
not allow battery acid to
contact your sk in, eyes,
clothing or paint finish.
(Continued)
WARNING

Page 355 of 400

1.((
,204/3424-3
WWheel replacement When replacing the metal wheels for
any reason, make sure the new
wheels are equivalent to the original
factory units in diameter, rim width
and offset.
Tire tractionTire traction can be reduced if you
drive on worn tires, tires that are
improperly inflated or on slippery
road surfaces. Tires should be
replaced when tread wear indicators
appear. Slow down whenever there
is rain, snow or ice on the road, to
reduce the possibility of losing con-
trol of the vehicle.Tire maintenance In addition to proper inflation, correct
wheel alignment helps decrease tire
wear. If you find a tire worn unevenly,
have your dealer check the wheel
alignment.
When you have new tires installed,
make sure they are balanced. This
will increase vehicle ride comfort and
tire life. Additionally, a tire should
always be rebalanced if it is removed
from the wheel.
Tire sidewall labelingThis information identifies and
describes the fundamental charac-
teristics of the tire and also provides
the tire identification number (TIN)
for safety standard certification. The
TIN can be used to identify the tire in
case of a recall.1. Manufacturer or brand nameManufacturer or Brand name is
shown.
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
a bilities, handling characteristics,
ground clearance, body-to-tire
clearance, snow chain clearance,
spee dometer and odometer cali-
bration, headlight aim and bumper
height.
WARNING
I030B04JM
1
1
2
34
5,6
7

Page 361 of 400

1.#&
,204/3424-3
$
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses.
This vehicle has 2 fuse panels, one
located in the driver’s side panel bol-
ster, the other in the engine compart-
ment near the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If a fuse
has blown, the element inside the
fuse will be melted.
If the electrical system does not
work, first check the driver’s side
fuse panel.
Before replacing a blown fuse, dis-
connect the negative battery cable.
Always replace a blown fuse with
one of the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and imme-
diately consult an authorized
HYUNDAI dealer.Three kinds of fuses are used: blade type for lower amperage rating, slowblow type and multi fuse for higheramperage ratings.
Do not use a screwdriver or any
other metal object to remove fuses
because it may cause a short circuit
and damage the system.
Information
The actual fuse/relay panel label may
differ from equipped items. iNOTICENOTICE
OTA070039
Normal
Normal
■ Slow Blow type
■ Multi fuse
B
B
l
l
o
o
w
w
n
n
Normal

Blade type
Fuse replacement•
Never replace a fuse with any-
thing but another fuse of the
same rating.

A higher capacity fuse could
cause damage and possibly a
fire.

Never install a wire or aluminum
foil instead of the proper fuse -
even as a temporary repair. It
may ca use extensive wiring
damage and a possible fire.
WARNING
B
B
l
l
o
o
w
w
n
n
B
B
l
l
o
o
w
w
n
n

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 61-70 next >