brake sensor HYUNDAI I20 2017 Owners Manual

 
"&t%'s%st&'!"'%!'&&

• Front air bags may not inflate inside impact collisions, becauseoccupants move to the direction of
the collision, and thus in sideimpacts, frontal air bag deployment
would not provide additional occu
pant protection.
However, side impact or curtain air
bags may inflate depending on the
intensity, vehicle speed and angles
of impact. • In a slant or angled collision, the
force of impact may direct the
occupants in a direction where the
air bags would not be able to pro
vide any additional benefit, and
thus the sensors may not deploy
any air bags. • Just before impact, drivers often
brake heavily. Such heavy braking
lowers the front portion of the vehi
cle causing it to “ride” under a vehi
cle with a higher ground clearance.
Air bags may not inflate in this
"underride" situation because
deceleration forces that are detect
ed by sensors may be significantly
reduced by such “underride” colli
sions.
OSA038121OBH038060OPA037043

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3Types of warning indicator and
sound
••If an object is in between sensors
or close to a sensor, the displayed
indicator may differ from the above
illustration.
• Do not wash the vehicle's sensor with high pressure water.
• When you shift into the R (Reverse) position and one or
more of the below situation occurs,
this may indicate a malfunction
with the parking assist system.
• You don't hear an audible warning sound or the buzzer sounds inter-
mittently.
If this occurs, we recommend that
the system be checked by an
authorized HYUNDAI dealer.
Non-operational conditions of Parking Distance Warning(Reverse) SystemThe Parking Distance Warning
(Reverse) System may not operate
normally when:• Moisture is frozen to the sensor.
• The sensor is covered or stained
with foreign material, such as snow
or water, or the sensor cover is
blocked.There is a possibility of a parking
assist system malfunction when:• Driving on uneven road surfacessuch as unpaved roads, gravel,
bumps, or gradient.
• Objects generating excessive noise such as vehicle horns, loud motor-
cycle engines, or truck air brakes
can interfere with the sensor.
• Heavy rain or water spray is present.
• Wireless transmitters or mobile phones are present near the sensor.
• The sensor is covered with snow.
• Any non-factory equipment or accessories have been installed, or
if the vehicle bumper height or sen-
sor installation has been modified.
NOTICE
Distance from
object
Warning
indicator
Warning sound
120cm ~ 61cm
(47 in. ~ 24 in.)
Buzzer beeps
intermittently.
60cm ~ 31cm
(24 in. ~ 12 in.)
Buzzer beeps
more frequently.
Less than
30 cm (12 in.)
Buzzer beeps continuously.
• is displayed. (if equipped)

1.#',204/3424-3
FFuse Name
Symbol
Fuse rating
Circuit Protected
SENSOR
10A
Diesel 1.4 : Fuel Filter Warning Sensor
MODULE3
10A
A/C Control Module, E/R Junction Block (Multipurpose Check Conn ector), ATM Shift
Lever ILL., Center Facia Switch, Audio
PDM1
25A
Smart Key Control Module
PDM2
10A
Smart Key Control Module, Start/Stop Button Switch
MODULE2
10A
Parking Distance Warning Buzzer, Parking Distance Warning-Reverse LH/RH, Parking
Distance Warning-Reverse (CENTER) LH/RH
TCU
15A
CVT : Transaxle Range Switch, Pulse Generator 'A' / 'B',
M/T : Vehicle Speed Sensor, I/P Junction Block (Fuse - F26)
TA I L L P R H
RH
10A
Rear Combination Lamp (In/Out) RH, Head Lamp RH, ILL. (+), License Lamp (4DR),
License Lamp LH/RH (5DR)
TA I L L P L H
LH
10A
Rear Combination Lamp (In/Out) LH, Head Lamp LH, License Lamp
RR WIPER
15A
Rear Wiper Motor, PCB Block (Rear Wiper Relay)
ABS
10A
ABS Control Module
A/BAG
10A
SRS Control Module
ECU
10A
PCM/ECM, Smart Key Control Module
BRAKE SWITCH
10A
Stop Lamp Switch, Smart Key Control Module
CLUSTER
10A
Instrument Cluster
Driver’s side fuse panel

1.'(
,204/3424-3
$  "$# $Exterior careExterior general caution It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label. High-pressure washing• When using high-pressure washers,
make sure to maintain sufficient dis-
tance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
• Do not spray the camera, sensors or its surrounding area directly with a
high pressure washer. Shock appliedfrom high pressure water may cause
the device to not operate normally.• Do not bring the nozzle tip close to boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
Finish maintenanceWashing To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear and
clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits. A mild soap, safe for
use on painted surfaces, may be
used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the fin-
ish.
• Do not use strong soap, chemicaldetergents or hot water, and do not
wash the vehicle in direct sunlig ht
or when the body of the vehicle is
warm.
• Be careful when washing the side windows of your vehicle.
Especially, with high-pressure
water, water may leak through the
windows and wet the interior.
• To prevent dam age to the plastic
parts and lamps, do not clean with
chemical solvents or strong deter- gents. NOTICEWet brakes
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
water. If braking performance is
impaired, dry the brakes by apply-
ing them lightly while maint aining
a slow forward speed.
WARNING