HYUNDAI I20 2018 Owners Manual

$$!%%#$#%
$#!!" !If the engine doesn't turn over or
turns over slowly • Be sure the shift lever is in N
(Neutral) or P (Park) if it is a
Continuously Variable Transaxle
vehicle. The engine starts only
when the shift lever is in N
(Neutral) or P (Park).
• Check the battery connections to be sure they are clean and tight.
• Turn on the interior light. If the light dims or goes out when you operate
the starter, the battery is drained.
Do not push or pull the vehicle to
start it. This could cause damage to
your vehicle. See instructions for "Jump Starting"
provided in this chapter.
If the engine turns over normally but doesn't start • Check the fuel level and add fuel if
necessary.
If the engine still does not start, we
recommend that you call an author-
ized HYUNDAI dealer for assistance.
!$#'#"'"' %'$%'&&&%Push or pull starting the vehicle
may cause the catalytic converter
to overload which can lead to
damage to the emission control
system.
WARNING

Jump starting can be dangerous if
done incorrectly. Follow the jump
starting procedure in this section to
avoid serious injury or damage to
your vehicle. If in doubt about how to
properly jump start your vehicle, we
strongly recommend that you have a
service technician or towing service
do it for you.!" !$#
!
$#'#"'"' %'$%'&&&%
To prevent SERIOUS INJURY or
DEATH to you or bystanders,
always follow these precautions
when working ne ar or handling the
battery:
Always read and follow
instructions carefully when
handling a battery.
Wear e ye protection
designed to protect the
eyes from acid splashes.
Keep all flames, sparks, or
smoking materi als away
from the battery.
Hydrogen is always pres-
ent in battery cells, is high-
ly combustible, and ma y
explode if ignited.
(Continued)
(Continued)
Keep batteries out of
reach of children.
Batteries contain sulfuric
acid which is highly corro-
sive. Do not allow acid to
contact your eyes, skin or
clothing.
If acid gets into your eyes, flush
your eyes with clean water for at
least 15 minutes and get immedi-
ate medical attention. If acid gets
on yo ur skin, thoroughly wash the
area. If you feel pain or a burning
sensation, get medical attention
immedi ately.•
When lifting a plastic-cased bat-
tery, excessive pressure on the
case may cause battery acid to
leak. L ift with a battery carrier or
with your hands on opposite cor-
ners.
•
Do not attempt to jump start
your vehicle if your battery is
frozen.
(Continued)
WARNING
(Continued)•
NEVER attempt to recharge the
battery when the vehicle’s bat-
tery cables are connected to the
battery.
•
The electrical ignition system
works with high voltage. NEVER
touch these components with
the engine run ning or when the
ignition switch is in the ON posi-
tion.
•
Do not allow the (+) and (-)
jumper cables to touch. It may
cause sparks.
•
The battery may rupture or
explode when you jump start
with a low or frozen battery.
•
Never attempt jump start if you
observe cracks, leaks or other
damage on Battery.

TTo prevent damage to your vehicle:
• Only use a 12-volt power supply (battery or jumper system) to jump
s tart your vehicle.
• Do not attempt to jump start your vehicle by push-starting.
Information
An inappropriately disposedbattery can be harmful to the
environment and human
health. Dispose the battery
according to your local law(s)
or regulation.
Jump starting procedure 1.Position the vehicles close enough that the jumper cables will reach,
but do not allow the vehicles to
touch.
2.Avoid fans or any moving parts in the engine compartment at all
times, even when the vehicles are
turned off.
3.Turn off all electrical devices such as radios, lights, air conditioning,
etc. Put the vehicles in P (Park, for
Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle), and set the
parking brakes. Turn both vehicles
OFF.
iNOTICE
!$#'#"'"' %'$%'&&&%
Pb
•
Improper jump starting proce-
dure can result in battery explo-
sion and acid burn hazard.
•
Loosely connected battery
cables could damage the elec-
tronic control units.
•
To disconnect battery terminals
wait for at least 2 minutes to
allow discharge of high voltage
or it cou ld lead to personal
injury.
•
While disconnecting, always dis-
connect the -VE terminal first
and while connecting, always
connect the -VE terminal last.
CAUTION

4.Connect the jumper cables in theexact sequence shown in the illus-
tration. First connect one jumper
cable to the red, positive (+)
jumper terminal of your vehicle (1).
5.Connect the other end of the jumper cable to the red, positive
(+) battery/jumper terminal of the
assisting vehicle (2).
6.Connect the second jumper cable to the black, negative (-)
battery/chassis ground of the
assisting vehicle (3). 7.Connect the other end of the sec-
ond jumper cable to the black, neg-
ative (-) chassis ground of your
vehicle (4).
Do not allow the jumper cables to
contact anything except the correct
battery or jumper terminals or the
correct ground. Do not lean over
the battery when making connec-
tions.
8.Start the engine of the assisting vehicle and let it run at approxi-
mately 2,000 rpm for a few min-
utes. Then start your vehicle.
If your vehicle will not start after a
few attempts, it probably requires
servicing. In this event please seek
qualified assistance. If the cause of
your battery discharging is not
apparent, we recommend that your
vehicle be checked by an authorized
HYUNDAI dealer. Disconnect the jumper cables in the
exact reverse order you connected
them:
1.Disconnect the jumper cable from
the black, negative (-) chassis
ground of your vehicle (4).
2.Disconnect the other end of the jumper cable from the black, nega-
tive (-) battery/chassis ground of
the assisting vehicle (3).
3.Disconnect the second jumper cable from the red, positive (+) bat-
tery/jumper terminal of the assist-
ing vehicle (2).
4.Disconnect the other end of the jumper cable from the red, positive
(+) jumper terminal of your vehicle
(1).
!
$#'#"'"' %'$%'&&&%
OLMB063002/Q
Jumper Terminal
Jumper Cables
Booster Battery
(-)
(+) (+)
(-)
Never connect Jumper Cable
directly to the negative (-) terminal
of discharged Battery (Your
Vehicle Bat tery), or an Explosion
may occur.
WARNING

If your temperature gauge indicates
overheating, you experience a loss
of power, or hear loud pinging or
knocking, the engine may be over-
heating. If this happens, you should:
1.Pull off the road and stop as soonas it is safe to do so.
2.Place the shift lever in P (Park, for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle) and set the
parking brake. If the air condition-
ing is ON, turn it OFF.
3.If engine coolant is running out under the vehicle or steam is com-
ing out from the hood, stop the
engine. Do not open the hood until
the coolant has stopped running or
the steaming has stopped. If there
is no visible loss of engine coolant
and no steam, leave the engine
running and check to be sure the
engine cooling fan is operating. If
the fan is not running, turn the
engine off. 4.Check for coolant leaking from the
radiator, hoses or under the vehi-
cle. (If the air conditioning had
been in use, it is normal for cold
water to be draining from it when
you stop.)
5.If engine coolant is leaking out, stop the engine immediately and
we recommend that you call an
authorized HYUNDAI dealer for
assistance.$$ !%%#$#%% %"!!!$#'#"'"' %'$%'&&&%
While the engine is run-
ning, keep hands,
clothing and tools away
from the moving parts
such as the cool ing fan
and drive belt to pre-
vent serious injury.WARNING
NEVER remove the
radiator cap or the
drain plug while the
engine and radiator are
hot. Hot coolant and
ste am may blow out under pres-
sure, causing serious injury.
Turn the engine off and wait until
the engine cools down. Use
extreme care when removing the
radiator cap. Wrap a thick towel
around it, and turn it c ounterclock-
wise slowly to the first stop. Step
back while the pressure is
released from the cooling sy stem.
When you are sure all the pres-
sure has been released, press
down on the cap, using a thick
towel, and continue turning coun-
terclockwise to remove it.WARNING

6.If you cannot find the cause of theoverheating, wait until the engine
temperature has returned to nor-
mal. Then, if coolant has been lost,
carefully add coolant to the reser-
voir to bring the fluid level in the
reservoir up to the halfway mark.
7.Proceed with caution, keeping alert for further signs of overheat-
ing. If overheating happens again,
we recommend that you call an
authorized HYUNDAI dealer for
assistance. •
•
Serious loss of coolant indicates a
leak in the cooling system and we
recommend the system be
checked b y an authorized
HYUNDAI dealer.
• When the engine overheats from low engine coolant, suddenly
adding engin e coolant may cause
cracks in the engine. To prevent
damage, add engine coolant slow-
ly in small quanti ties.NOTICE
!
$#'#"'"' %'$%'&&&%

! $#'#"'"' %'$%'&&&%
JJack and tools ➀Jack
➁ Jack handle
➂ Wheel lug nut wrench
➃ Towing hook
The jack, jack handle, and wheel lug
nut wrench, towing hook are stored
in the luggage compartment under
the luggage box cover.
The jack is provided for emergency
tire changing only.
Removing and storing the spare
tireTurn the winged hold down bolt
counterclockwise to remove the
spare tire.
Store the spare tire in the same com-
partment by turning the winged hold
down bolt clockwise.
To prevent the spare tire and tools
from “rattling,” store them in their
proper location.
$"%""!!$ %
OIB067021
OIB067020
Changing a tire can be dangerous.
Follow the instructions in this sec-
tion when changing a tire to
redu ce the risk of serious injury or
death.
WARNING

!
$#'#"'"' %'$%'&&&%
If it is hard to loosen the tire hold-
down wing bolt by hand, you can
loosen it easily using the wheel lug
nut wrench.
1. Put the wrench (1) inside of the tire hold-down wing bolt.
2. Turn the tire hold-down wing bolt counterclockwise with the wrench.
CChanging tires A vehicle can slip or roll off of a
jack causing serious injury or
death to you or those nearby.
Take th e following safety precau-
tions:•
Do not get under a vehicle that
is supported by a jack.
•
NEVER attempt to change a tire
in the lane of traffic. ALWAYS
move the vehicle completely off
the road o n level, firm ground
away from traffic before trying to
change a tire. If you cannot find
a level, firm place off the road,
call a towing service for assis-
tance.
•
Be sure to use the jack provided
with the vehicle.
(Continued)
(Continued)•
ALWAYS place the jack on the
designated jacking positions on
the vehicle and NEVER on the
bumpers or any other part of the
vehicle for jacking support.
•
Do not start or run the engine
while the vehicle is on the jack.
•
Do not allow anyone to remain
in the vehicle while it is on the
jack.
•
Keep children away from the
road and the vehicle.
WARNING
OIB067022

!$#'#"'"' %'$%'&&&%
Follow these steps to change your
v ehicle’s tire:
1.Park on a level, firm surface.
2.Move the shift lever into P (Park, for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle), apply the park-
ing brake, and place the ignition
switch in the LOCK/OFF position.
3.Press the hazard warning flasher button.
4.Remove the wheel lug nut wrench, jack, jack handle, and spare tire
from the vehicle.
5.Block both the front and rear of the tire diagonally opposite of the tire
you are changing. 6.Loosen the wheel lug nuts counter-
clockwise one turn each in the
order shown above, but do not
remove any lug nuts until the tire
has been raised off of the ground. 7.Place the jack at the designated
jacking position under the frame
closest to the tire you are chang-
ing. The jacking positions are
plates welded to the frame with two
tabs and a raised dot. Never jack
any other position or part of the
vehicle.
OIB067006
OIB067005

!

$#'#"'"' %'$%'&&&%
8.Insert the jack handle into the jackand turn it clockwise, raising the
vehicle until the tire clears the ground. Make sure the vehicle is
stable on the jack. 9.Loosen the lug nuts with the wheel
lug nut wrench and remove them
with your fingers. Remove the
wheel from the studs and lay it flat
on the ground out of the way.
Remove any dirt or debris from the
studs, mounting surfaces, and
wheel.
10. Install the spare tire onto the studs of the hub.
11. Tighten the lug nuts with your fin- gers onto the studs with the
smaller end of the lug nuts clos-
est to the wheel.
12. Lower the vehicle to the ground by turning the jack handle coun-
terclockwise. 13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug
nut until they are tight. After
changing tires, we recommend
that an authorized HYUNDAI
dealer tighten the lug nuts to their
proper torque as soon as possi-
ble. T
T
he wheel lug nut should be
tightened to 11~13 kgf.m (79~94
lbf.ft).
OIB067008
OIB067007