Lock HYUNDAI I20 2023 Owners Manual
Page 585 of 649
9-26
Maintenance
Filter inspection
The climate control air filter should be
replaced according to the Maintenance
Schedule. If the vehicle is operated in
severely air-polluted cities or on dusty
rough roads for a long period, it should
be inspected more frequently and
replaced earlier. When you replace the
climate control air filter, replace it by
performing the following procedure,
and be careful to avoid damaging other
components.
Replace the filter according to the
Maintenance Schedule.
Filter replacement
OBC3050036R
1. Open the glove box.
OBC3090022R
2. Push in both sides of the glove box as
shown. This will ensure that the glove
box stopper pins will get released
from its holding location allowing the
glove box to hang.
OBC3N090013
3. Press and hold the lock on the left side
of the cover.
4. Pull out the cover.
5. Replace the climate control air filter.
6. Reassemble in the reverse order of
disassembly.
NOTICE
ODH073012
Install a new climate control air filter
in the correct direction with the
arrow symbol ( ) facing downwards,
otherwise, it may be noisy and the
effectiveness of the filter may be
reduced.
CLIMATE CONTROL AIR FILTER
Page 610 of 649
9-51
09
6 P D U W V W U H D P * 7 * ' L 6 P D U W V W U H D P * 7 * ' L + ( 9
Fuse Name Symbol (A) Circuit Protected
ALT(180A)
[150A]Alternator, Multi Fuse - F2, Fuse - F31/F32/F33/F34/
F35/F36
MDPS
80A MDPS Unit
DCT1
40ATCM
E-CLUTCH1Electronic Clutch Module
DCT2
40A TCM
ECU1
30A E/R Junction Block (RLY.1)
IG1
30A[With Smart Key] PDM Relay Box (IG1, ACC Relay)
[W/O Smart Key] Ignition Switch
FUEL PUMP
20A E/R Junction Block (RLY.5)
BATTERY
MANAGEMENT1
15A E/R Junction Block (Fuse - F40/F43)
ECU3
15A ECM, Clutch Switch
ECU2
15A ECM
A/CON 1
10A E/R Junction Block (RLY.10)
DCT4
40A Smart Gear Actuator
CVVD
40A CVVD Actuator
IG2
30A[With Smart Key] PDM Relay Box (IG2 Relay)
[W/O Smart Key] Ignition Switch, START MTR RLY
BATT1
50AICU Junction Block (IPS1, IPS3, IPS5, IPS7, IPS8,
IPS11)
BATT3
50AICU Junction Block (Fuse - F8/F15/F21/F25/F29,
Long Term Load Latch Relay-F16/F9/F22)
DCT3
15A TCM
E-CLUTCH2Electronic Clutch Module
HORN
15A E/R Junction Block (RLY.11, RLY.12)
AMS
10A Battery Sensor
BATT2
50A ICU Junction Block (IPS2, IPS4, IPS6, IPS9, IPS10)
BATT4
50AICU Junction Block (Power Window Relay-F5/F12,
Fuse - F3/F4/F10/F11)
C/FAN
60A E/R Junction Block (RLY.2)
Page 611 of 649
9-52
Maintenance
Fuse Name Symbol (A) Circuit Protected
IGN COIL15A Ignition Coil #1/#2/#3
ECU5
20A ECM
ECU6
15A ECM
SENSOR 1
10AE/R Junction Block (RLY.2/10),
Oil Control Valve #1/#2 (Intake/Exhaust),
Purge Control Solenoid Valve, RCV Control, V_Oil
Pump Solenoid Valve
SENSOR 2
10A Oxygen Sensor (Up/Down)
RR DEFOG
40A ICU Junction Block (Rear Defogger Relay)
ABS 1
40A ESP Control Module
BLOWER
40A E/R Junction Block (RLY.13)
PTC
HEATER
50A E/R Junction Block (RLY.14)
ABS 2
30A ESP Control Module
POWER
OUTLET
40A ICU Junction Block (Power Outlet Relay)
WIPER 2
10A E/T Junction Block (RLY. 4), Front Wiper Motor, IBU
SENSOR3
15A E/T Junction Block (RLY. 5)
MHSG
10A Mild Hybrid Starter & Generator Motor
BATTERY
C/FAN
10A BMS Cooling Fan, E/R Junction Block (Fuse - F8)
WIPER 1
25AE/T Junction Block (RLY. 4), Front Wiper Motor,
Ignition Switch
BATTERY
MANAGEMENT2
10ABMS Control Module, E/R Junction Block (Fuse -
F8)
6 P D U W V W U H D P * 7 * ' L 6 P D U W V W U H D P * 7 * ' L + ( 9
Page 613 of 649
9-54
Maintenance
Fuse Name Symbol (A) Circuit Protected
ALT(125A)
[150A]Alternator, Multi Fuse - F2, Fuse - F31/F32/F33/F34/
F35/F36
MDPS
80A MDPS Unit
ECU1
30A E/R Junction Block (RLY.1)
IG1
30A[With Smart Key] PDM Relay Box (IG1, ACC Relay)
[W/O Smart Key] Ignition Switch
FUEL PUMP
20A E/R Junction Block (RLY.5)
ECU3
15A ECM, Clutch Switch
ECU2
15A ECM
A/CON 1
10A E/R Junction Block (RLY.8)
IG2
30A[With Smart Key] PDM Relay Box (IG2 Relay)
[W/O Smart Key] Ignition Switch, START MTR RLY
BATT1
50AICU Junction Block (IPS1, IPS3, IPS5, IPS7, IPS8,
IPS11)
BATT3
50AICU Junction Block (Fuse - F8/F15/F21/F25/F29,
Long Term Load Latch Relay-F16/F9/F22)
HORN
15A E/R Junction Block (RLY.11, RLY.12)
AMS
10A Battery Sensor
BATT2
50A ICU Junction Block (IPS2, IPS4, IPS6, IPS9, IPS10)
BATT4
50AICU Junction Block (Power Window Relay-F5/F12,
Fuse - F3/F4/F10/F11)
C/FAN
40A E/R Junction Block (RLY.9/10)
IGN COIL
20A Ignition Coil #1/#2/#3/#4
ECU5
20A ECM
ECU6
15A ECM
SENSOR 1
10AE/R Junction Block (RLY.8/9/10),
Oil Control Valve #1/#2 (Intake/Exhaust),
Purge Control Solenoid Valve
SENSOR 2
10A Oxygen Sensor (Up/Down)
RR DEFOG
40A ICU Junction Block (Rear Defogger Relay)
ABS 1
40A ESP Control Module
6 P D U W V W U H D P *
Page 614 of 649
9-55
09
6 P D U W V W U H D P *
Fuse Name Symbol (A) Circuit Protected
BLOWER40A E/R Junction Block (RLY.13)
PTC
HEATER
50A E/R Junction Block (RLY.14)
ABS 2
30A ESP Control Module
POWER
OUTLET
40A ICU Junction Block (Power Outlet Relay)
WIPER 2
10A E/R Junction Block (RLY. 4), Front Wiper Motor, IBU
INJECTOR1
15AE/R Junction Block (RLY. 5), Injector #1-1/#2-1/#3-
1/#4-1
INJECTOR2
15A Injector #1-2/#2-2/#3-2/#4-2
WIPER 1
25AE/T Junction Block (RLY. 4), Front Wiper Motor,
Ignition Switch
Page 616 of 649
9-57
09
3 H W U R O
Fuse Name Symbol (A) Circuit Protected
ALT(125A)
[150A]Alternator, Multi Fuse - F2, Fuse - F31/F32/F33/F34/
F35/F36
MDPS
80A MDPS Unit
ECU1
30A E/R Junction Block (RLY.1)
IG1
30A[With Smart Key] PDM Relay Box (IG1, ACC Relay)
[W/O Smart Key] Ignition Switch
FUEL PUMP
20A E/R Junction Block (RLY.5)
TCU1
15A PCM, Clutch Switch
ECU2
15A ECM/PCM
EOP
40A Electronic Oil Pump
IG2
30A[With Smart Key] PDM Relay Box (IG2 Relay)
[W/O Smart Key] Ignition Switch, START MTR RLY
BATT1
50AICU Junction Block (IPS1, IPS3, IPS5, IPS7, IPS8,
IPS11)
BATT3
50AICU Junction Block (Fuse - F8/F15/F21/F25/F29,
Long Term Load Latch Relay-F16/F9/F22)
HORN
15A E/R Junction Block (RLY.11, RLY.12)
AMS
10A Battery Sensor
BATT2
50A ICU Junction Block (IPS2, IPS4, IPS6, IPS9, IPS10)
BATT4
50AICU Junction Block (Power Window Relay-F5/F12,
Fuse - F3/F4/F10/F11)
C/FAN
40A E/R Junction Block (RLY.9/10)
IGN COIL
20A Ignition Coil #1/#2/#3/#4, Condensor
ECU5
20A ECM/PCM
ECU6
15A ECM/PCM
SENSOR 1
10AE/R Junction Block (RLY.9/10),
Oil Control Valve #1/#2 (Intake/Exhaust),
Purge Control Solenoid Valve, Variable Intake
Solenoid Valve
SENSOR 2
10A Oxygen Sensor (Up/Down)
RR DEFOG
40A ICU Junction Block (Rear Defogger Relay)
Page 617 of 649
9-58
Maintenance
3 H W U R O
Fuse Name Symbol (A) Circuit Protected
ABS 140A ESP Control Module
BLOWER
40A E/R Junction Block (RLY.13)
PTC
HEATER
50A E/R Junction Block (RLY.14)
ABS 2
30A ESP Control Module
POWER
OUTLET
40A ICU Junction Block (Power Outlet Relay)
WIPER 2
10A E/R Junction Block (RLY. 4), Front Wiper Motor, IBU
INJECTOR
15A E/R Junction Block (RLY. 5), Injector #1/#2/#3/#4
WIPER 1
25AE/R Junction Block (RLY. 4), Front Wiper Motor,
Ignition Switch
Page 618 of 649
9-59
09
We recommend that you consult with a
HYUNDAI authorised repairer to replace
most vehicle light bulbs. It is difficult
to replace vehicle light bulbs because
other parts of the vehicle must be
removed before you can get to the bulb.
This is especially true for removing the
headlight assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to the
vehicle.
WARNING
Prior to replacing a light, depress the
foot brake, move the shift lever into the
N (Neutral, for automatic transmission
vehicle) or neutral (for manual
transmission vehicle), apply the parking
brake, place the ignition switch in the
LOCK/OFF position, and take the key
with you when leaving the vehicle to
avoid sudden movement of the vehicle
and to prevent possible electric shock.
% H D Z D U H W K H E X O E V P D \ E H K R W D Q G P D \
burn your fingers.
NOTICE
% H V X U H W R U H S O D F H W K H E X U Q H G R X W E X O E
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electric wiring system.
i Information
7 K H K H D G O L J K W D Q G W D L O O D P S O H Q V H V F R X O G
D S S H D U I U R V W \ L I W K H Y H K L F O H L V Z D V K H G D I W H U
G U L Y L Q J R U W K H Y H K L F O H L V G U L Y H Q D W Q L J K W
L Q Z H W Z H D W K H U 7 K L V F R Q G L W L R Q L V F D X V H G
E \ W H P S H U D W X U H G L I I H U H Q F H E H W Z H H Q W K H
O D P S L Q V L G H D Q G R X W V L G H D Q G L W G R H V Q R W
L Q G L F D W H D S U R E O H P Z L W K \ R X U Y H K L F O H
: K H Q P R L V W X U H F R Q G H Q V H V L Q W K H O D P S
L W Z L O O E H U H P R Y H G D I W H U G U L Y L Q J Z L W K W K H
K H D G O L J K W R Q 7 K H U H P R Y D E O H O H Y H O P D \
G L I I H U G H S H Q G L Q J R Q O D P S V L ] H O D P S
S R V L W L R Q D Q G H Q Y L U R Q P H Q W D O F R Q G L W L R Q
+ R Z H Y H U L I P R L V W X U H L V Q R W U H P R Y H G Z H
U H F R P P H Q G W K D W \ R X U Y H K L F O H L V L Q V S H F W H G
E \ D + < 8 1 ' $ , D X W K R U L V H G U H S D L U H U
i Information (For Europe)
7 U D I I L F & K D Q J H
7 K H O R Z E H D P O L J K W G L V W U L E X W L R Q L V
D V \ P P H W U L F , I \ R X J R D E U R D G W R D F R X Q W U \
Z L W K R S S R V L W H W U D I I L F G L U H F W L R Q W K L V
D V \ P P H W U L F S D U W Z L O O G D ] ] O H R Q F R P L Q J F D U
G U L Y H U 7 R S U H Y H Q W G D ] ] O H ( & ( U H J X O D W L R Q
G H P D Q G V V H Y H U D O W H F K Q L F D O V R O X W L R Q V H [
D X W R P D W L F F K D Q J H V \ V W H P D G K H V L Y H V K H H W
G R Z Q D L P L Q J 7 K H V H K H D G O L J K W V D U H
G H V L J Q H G Q R W W R G D ] ] O H R S S R V L W H G U L Y H U V
6 R \ R X Q H H G Q R W F K D Q J H \ R X U K H D G O L J K W V
L Q D F R X Q W U \ Z L W K W K H R S S R V L W H W U D I I L F
G L U H F W L R Q
LIGHT BULBS
Page 621 of 649
9-62
Maintenance
+ H D G O L J K W / R Z + L J K
1. Turn the front wheel at inwards.
OAC3089042TU
OAC3089043TU
OBC3090055
2. Remove the Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blots (C).
3. Push the wheel guard aside and
remove the headlight bulb cover by
turning it counterclockwise from bulb
assembly.
OBC3090038
OBC3TN091005
„CUV
4. Disconnect the headlight bulb socket-
connector.
5. Unsnap the headlight bulb retaining
wire by depressing the end and
pushing it upward.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.
Page 622 of 649
9-63
09
OBC3090039
OBC3TN091006
„CUV
7 X U Q V L J Q D O O L J K W
1. Open the bonnet.
2. Remove the turn signal light or low
beam assist-static light bulb cover by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
3 R V L W L R Q O L J K W ' D \ W L P H U X Q Q L Q J O L J K W
L I H T X L S S H G
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamp has to be replaced
with the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.