Lock HYUNDAI I20 2023 Owners Manual

9-65
09
„Front Fog light
OBC3090040
)RJOLJKWLIHTXLSSHG
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.
Headlight and front fog light
aiming (For Europe, if equipped)
Headlight aiming
„Type A
OBC3090041
„Type B
OBC3090057
„Type C
OBC3TN091004
1. Inflate the tyres to the specified
pressure and remove any loads from
the vehicle except the driver, spare
tyre, and tools.
2. The vehicle should be placed on a flat
floor.

9-66
Maintenance
3. Draw vertical lines (Vertical lines
passing through respective head
light centres) and a horizontal line
(Horizontal line passing through
centre of head lamps) on the screen.
4. With the headlight and battery in
normal condition, aim the headlights
so the brightest portion falls on the
horizontal and vertical lines.
5. To aim the low beam left or
right, turn the driver clockwise or
counterclockwise. To aim the low
beam up or down, turn the driver
clockwise or counterclockwise.
To aim the high beam up or
down, turn the driver clockwise or
counterclockwise.Front fog light aiming (if equipped)
OBC3090042
The front fog light can be aimed as the
same manner of the head lights aiming.
With the front fog lights and battery
normal condition, aim the front fog
lights. To aim the front fog light up
or down, turn the driver clockwise or
counterclockwise.

9-70
Maintenance
Side repeater light replacement
Type A
OBC3090044
If the LED lamp does not operate, we
recommend you to have the vehicle
checked by a HYUNDAI authorised
repairer.
Type B
OAC3089047TU
1. Remove the lamp assembly from the
vehicle by prying the lens and pulling
the assembly out.
2. Disconnect the bulb electrical
connector.
3. Separate the socket and the
lens parts by turning the socket
counterclockwise until the tabs on the
socket align with the slots on the lens
part.
4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens
part.
7. Connect the bulb electrical connector.
8. Reinstall the lamp assembly to the
body of the vehicle.

9-72
Maintenance
OBC3090047
[1] : Turn Signal Light, [2] : Tail/Stop Light,
[3] : Tail light
7XUQVLJQDOOLJKW7DLOVWRSOLJKW
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
7DLOOLJKW
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the nuts by turning the nuts
counter clockwise.
4. Take the light assembly out.
OBC3090049R
[1] : Rear Fog Light, [2] : Back-up Light
5HDUIRJOLJKW%DFNXS/LJKW
1. Remove the rear tire and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.

9-74
Maintenance
OBC3090048
[1] : Turn Signal Light,
7XUQVLJQDOOLJKW
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
7DLOOLJKW6WRSOLJKW
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit. The LED lamp has to be
replaced with the unit.
Unless a skilled technician checks or
repairs the LED lamp, it may damage
related parts of the vehicle.
OBC3090050
[1] : Rear Fog Light, [2] : Back-up Light
5HDUIRJOLJKW
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.
%DFNXSOLJKW
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the nuts by turning the nuts
counter clockwise.
4. Take the light assembly out.

9-76
Maintenance
OBC3V091003
[1] : Turn Signal Light, [2] : Tail/Stop Light,
[3] : Tail light
7XUQVLJQDOOLJKW7DLOVWRSOLJKW7DLO
OLJKW
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
OBC3V091004
[1] : Rear Fog Light
5HDUIRJOLJKW5HDUUHIOHFWLRQOLJKW
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.

9-77
09
Type D
OBC3V091006
(1) Turn signal lamp
(2) Tail/Stop light
(3) Rear fog light/Rear reflection light
7XUQVLJQDOODPS7DLOOLJKW6WRS
OLJKW
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. The LED lamps cannot be
replaced as a single unit because it is an
integrated unit.
The LED lamp has to be replaced with
the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.
OBC3V091004
[1] : Rear Fog Light
5HDUIRJOLJKW5HDUUHIOHFWLRQOLJKW
1. Remove the rear tyre and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.

9-78
Maintenance
High mounted stop light
replacement
OBC3090051
1. Open the tailgate.
2. Remove the socket by turning it
counterclockwise until the tabs on the
socket align with the slots.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
License plate light bulb
replacement
OAI3089029
1. Using a flat-blade screwdriver gently
pry the lens cover from the lamp
housing.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb by pulling it straight
out.
4. Install a new bulb.
5. Reinstall in the reverse order.