screen HYUNDAI I20 2023 User Guide
Page 196 of 649
5-55
05
AUTO (Automatic) control
(if equipped)
The rain sensor located at the top of the
windscreen glass senses the amount of
rainfall and controls the wiping cycle for
the proper interval. The wiper operation
time will be automatically controlled,
depending on rainfall.
When the rain stops, the wiper stops. To
vary the speed setting, turn the speed
control knob.
If the wiper switch is set in AUTO mode
when the ignition switch is in the ON
position, the wiper will operate once to
perform a self-check of the system. Set
the wiper to the OFF position when the
wiper is not in use.
WARNING
To avoid personal injury from the
windscreen wipers, when the engine
is running and the windscreen wiper
switch is placed in the AUTO mode:
Do not touch the upper end of the
windscreen glass facing the rain sensor.
Do not wipe the top of the windscreen
glass with a damp or wet cloth.
Do not put pressure on the windscreen
glass.
NOTICE
When washing the vehicle, set the
Z L S H U V Z L W F K L Q W K H 2 ) ) S R V L W L R Q W R V W R S
the auto wiper operation. The wiper
may operate and be damaged if the
switch is set in the AUTO mode whilst
washing the vehicle.
Do not remove the sensor cover
located at the top of the passenger side
windscreen glass. Damage to system
parts could occur and may not be
covered by your vehicle warranty.
Windscreen washers
OTLE045168
In the OFF (O) position, pull the lever
gently toward you to spray washer
fluid on the windscreen and to run the
wipers 1-3 cycles. The spray and wiper
operation will continue until you release
the lever. If the washer does not work,
you may need to add washer fluid to the
washer fluid reservoir.
WARNING
When the outside temperature is
below freezing, ALWAYS warm the
windscreen using the defroster to
prevent the washer fluid from freezing
on the windscreen and obscuring your
vision which could result in an accident
and serious injury or death.
Page 197 of 649
5-56
Convenient features
CAUTION
[ To prevent possible damage to the
washer pump, do not operate the
washer when the fluid reservoir is
empty.
[ To prevent possible damage to the
wipers or windscreen, do not operate
the wipers when the windscreen is
dry.
[ To prevent damage to the wiper
arms and other components, do
not attempt to move the wipers
manually.
[ To prevent possible damage to the
wipers and washer system, use anti-
freezing washer fluids in the winter
season or cold weather.
Rear window wiper and washer
switch (if equipped)
OTLE045167
The rear window wiper and washer
switch is located at the end of the wiper
and washer switch lever.
Turn the switch to desired position to
operate the rear wiper and washer.
· 2 – High wiper speed
· 1 – Low wiper speed
· O – Off
OTLE045167
Push the lever away from you to spray
rear washer fluid and to run the rear
wipers 1~3 cycles. The spray and wiper
operation will continue until you release
the lever. (if equipped)
Auto rear wiper (if equipped)
The rear wiper will operate whilst the
vehicle is in reverse with the front wiper
ON by selecting the function on the LCD
display.
* R W R S 8 V H U 6 H W W L Q J V
Page 200 of 649
5-59
05
OBC3050103
The mode selection knob controls the
direction of the air flow through the
ventilation system.
Air can be directed to the floor,
dashboard outlets, or windscreen. Five
symbols are used to represent Face,
Bi-Level, Floor, Floor-Defrost and
Defrost air position.
) D F H / H Y H O % '
Air flow is directed toward the upper
body and face. Additionally, each outlet
can be controlled to direct the air
discharged from the outlet.
% L / H Y H O % & '
Air flow is directed towards the face and
the floor.
) O R R U / H Y H O $ & '
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windscreen, side
window defrosters and side vents.
) O R R U ' H I U R V W / H Y H O
$ & '
Most of the air flow is directed to the
floor and the windscreen with a small
amount directed to the side window
defrosters and side vents.
' H I U R V W / H Y H O $ '
Most of the air flow is directed to the
windscreen with a small amount of air
directed to the side vents.
Page 202 of 649
5-61
05
i Information
2 S H U D W L Q J W K H V \ V W H P S U L P D U L O \ L Q ) U H V K
P R G H L V U H F R P P H Q G H G 8 V H 5 H F L U F X O D W L R Q
mode temporarily only when needed.
Prolonged operation of the heater in
5 H F L U F X O D W L R Q P R G H D Q G Z L W K R X W W K H $ &
2 1 F D Q F D X V H I R J J L Q J R I W K H Z L Q G V F U H H Q
, Q D G G L W L R Q S U R O R Q J H G X V H R I W K H $ &
2 1 L Q 5 H F L U F X O D W L R Q P R G H P D \ U H V X O W L Q
excessively dry, dehumidified air in the
cabin and may promote formation of
musty vent odor due to stagnant air.
WARNING
[ & R Q W L Q X H G X V H R I W K H F O L P D W H F R Q W U R O
system operation in Recirculation
mode for a prolonged period of
time may cause drowsiness to the
occupants in the cabin. This may lead
to loss of vehicle control which may
lead to an accident.
[ & R Q W L Q X H G X V H R I W K H F O L P D W H F R Q W U R O
system operation in Recirculation
P R G H Z L W K W K H $ & 2 ) ) P D \ D O O R Z
humidity to increase inside the cabin.
This may cause condensation to
accumulate on the windscreen and
obscure visibility.
[ ' R Q R W V O H H S L Q \ R X U Y H K L F O H R U
remain parked in your vehicle with
the windows up and either the
heater or the air conditioning ON for
prolonged periods of time. Doing so
may increase the levels of carbon
dioxide in the cabin which may lead
to serious injury or death.
Fan speed control
OBC3050106
Turn the knob to the right to increase
the fan speed and airflow. Turn the knob
to the left to decrease fan speed and
airflow.
Setting the fan speed control knob to
the “0” position turns off the fan.
NOTICE
Operating the fan speed when the
ignition switch is in the ON position
could cause the battery to discharge.
Operate the fan speed when the engine
is running.
Air conditioning (if equipped)
OBC3050107
Press the A/C button to turn the air
conditioning system on (indicator light
will illuminate). Press the button again to
turn the air conditioning system off.
Page 203 of 649
5-62
Convenient features
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press the
Front Defrost mode.
2 S H U D W L R Q 7 L S V
[ 7 R N H H S G X V W R U X Q S O H D V D Q W I X P H V
from entering the vehicle through the
ventilation system, temporarily set the
air intake control to the recirculation
mode. Be sure to return the control
to fresh mode position when the
irritation has passed to keep fresh air
in the vehicle. This will help keep the
driver alert and comfortable.
[ 7 R S U H Y H Q W L Q W H U L R U I R J R Q W K H
windscreen, set the air intake control
to fresh mode and fan speed to
the desired position, turn on the
air conditioning system, and adjust
the temperature control to desired
temperature.
Air conditioning
HYUNDAI Air Conditioning Systems are
filled with R-134a or R1234yf refrigerant.
1. Start the engine.
2. Push the air conditioning button.
3. Select the Face Level
mode.
4. Set the air intake control to
Recirculation mode temporarily to
allow the cabin to cool quickly. When
the desired temperature in the cabin
is reached, change the air intake
control back to Fresh mode.
5. Adjust the fan speed control and
temperature control to maintain
maximum comfort.
i Information
OBC3050052
< R X U Y H K L F O H L V I L O O H G Z L W K 5 D R U
5 \ I D F F R U G L Q J W R W K H U H J X O D W L R Q L Q
your country at the time of production.
< R X F D Q I L Q G R X W Z K L F K D L U F R Q G L W L R Q L Q J
refrigerant is applied to your vehicle on
the label located inside of the bonnet.
Page 208 of 649
5-67
05
Automatic heating and air
conditioning
OBC3050110R
1. Press the AUTO button.
The modes, fan speeds, air intake and
air-conditioning will be controlled
automatically according to the
temperature setting you select.
OBC3050111R
2. Push the temperature control switch
to set the desired temperature. If
the temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.
[ 7 R W X U Q W K H D X W R P D W L F R S H U D W L R Q R I I
select any button of the following:
- Mode selection button
- Front windscreen defroster button
(Press the button one more time
to deselect the front windscreen
G H I U R V W H U I X Q F W L R Q 7 K H S $ 8 7 2T V L J Q
will illuminate on the information
screen once again.) - Fan speed control toggle switch
The selected function will be
controlled manually whilst other
functions operate automatically.
[ ) R U \ R X U F R Q Y H Q L H Q F H X V H W K H $ 8 7 2
button and set the temperature to
22°C (72°F).
OAI3059112I
i Information
1 H Y H U S O D F H D Q \ W K L Q J Q H D U W K H V H Q V R U W R
ensure better control of the heating and
cooling system.
Page 210 of 649
5-69
05
OBC3050112R
The mode selection button controls the
direction of the air flow through the
ventilation system.
) D F H / H Y H O % '
Air flow is directed toward the upper
body and face. Additionally, each outlet
can be controlled to direct the air
discharged from the outlet.
) O R R U / H Y H O $ & '
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windscreen and
side window defrosters.
) O R R U ' H I U R V W $ & '
Most of the air flow is directed to the
floor and the windscreen with a small
amount directed to the side window
defrosters.
OBC3050113R
' H I U R V W / H Y H O $ '
Most of the air flow is directed to the
windscreen with a small amount of air
directed to the side window defrosters.
OBC3N051101AU
, Q V W U X P H Q W S D Q H O Y H Q W V
The instrument panel vent air flow can
be directed up/down or left/right using
the vent adjustment lever.
To close the vent adjustment lever,
rotate it to the outer side till the end. To
open the vent, rotate it to the inner side.
Page 211 of 649
5-70
Convenient features
Temperature control
OBC3050111R
The temperature will increase by
pushing the switch to up.
The temperature will decrease by
pushing the switch to down.
The temperature will increase or
decrease by 0.5°C (1°F) for each
incremental location. When set to the
lowest temperature setting, the air
conditioning will operate continuously.
7 H P S H U D W X U H F R Q Y H U V L R Q
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from °C
to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 seconds
whilst pressing the OFF button.
- Instrument cluster
Go to User Settings o Units o
Temperature Unit.
The temperature unit on both the cluster
LCD display and the climate control
screen will change.
Air intake control
OBC3050114R
This is used to select the outside (fresh)
air position or recirculated air position.
To change the air intake control position,
push the control button.
5 H F L U F X O D W H G D L U S R V L W L R Q
With the recirculated air
position selected, air from
the passenger
compartment will be
drawn through the heating
system and heated or
cooled according to the
function selected.
2 X W V L G H I U H V K D L U S R V L W L R Q
With the outside (fresh) air
position selected, air
enters the vehicle from
outside and is heated or
cooled according to the
function selected.
Page 212 of 649
5-71
05
i Information
2 S H U D W L Q J W K H V \ V W H P S U L P D U L O \ L Q ) U H V K
P R G H L V U H F R P P H Q G H G 8 V H 5 H F L U F X O D W L R Q
mode temporarily only when needed.
Prolonged operation of the heater in
5 H F L U F X O D W L R Q P R G H D Q G Z L W K R X W W K H $ &
2 1 F D Q F D X V H I R J J L Q J R I W K H Z L Q G V F U H H Q
, Q D G G L W L R Q S U R O R Q J H G X V H R I W K H $ &
2 1 L Q 5 H F L U F X O D W L R Q P R G H P D \ U H V X O W L Q
excessively dry, dehumidified air in the
cabin and may promote formation of
musty vent odor due to stagnant air.
WARNING
[ Continued use of the climate control
system operation in Recirculation
mode for a prolonged period of
time may cause drowsiness to the
occupants in the cabin. This may lead
to loss of vehicle control which may
lead to an accident.
[ Continued use of the climate control
system operation in Recirculation
P R G H Z L W K W K H $ & 2 ) ) P D \ D O O R Z
humidity to increase inside the cabin.
This may cause condensation to
accumulate on the windscreen and
obscure visibility.
[ Do not sleep in your vehicle or
remain parked in your vehicle with
the windows up and either the
heater or the air conditioning ON for
prolonged periods of time. Doing so
may increase the levels of carbon
dioxide in the cabin which may lead
to serious injury or death.
Fan speed control
OBC3050115R
Push the switch to up to increase the fan
speed and airflow. Push the switch to
down to decrease fan speed and airflow.
NOTICE
Operating the fan speed when the
ignition switch is in the ON position
could cause the battery to discharge.
Operate the fan speed when the engine
is running.
Page 213 of 649
5-72
Convenient features
Air conditioning
OBC3050116R
Push the A/C button to manually turn
the air conditioning system on (indicator
light will illuminate).
Push the button again to turn the air
conditioning system off.
OFF mode
OBC3050117R
Push the OFF button of the front to turn
off the climate control system.
You can still operate the air intake
buttons as long as the ignition switch is
in the ON position.
However, the air climate control system
turns on when you push the mode
selection buttons.
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning ON
with the temperature control knob set
to heat in order to dehumidify the air
before it enters into the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press the
Front Defrost mode.