Stop and go HYUNDAI I20 2023 Owner's Manual

Page 113 of 649

4-18
Instrument cluster
Immobiliser indicator
light (with smart key)
(if equipped)
7KLVLQGLFDWRUOLJKWLOOXPLQDWHVIRUXS
WRVHFRQGV
[When the vehicle detects the smart
key in the vehicle with the Engine
Start/Stop button in the ACC or ON
position.
- At this time, you can start the engine.
- The indicator light goes off after
starting the engine.
7KLVLQGLFDWRUOLJKWEOLQNVIRUDIHZ
VHFRQGV
[When the smart key is not in the
vehicle.
- At this time, you cannot start the
engine.
7KLVLQGLFDWRUOLJKWLOOXPLQDWHVIRU
VHFRQGVDQGJRHVRII
[If the smart key is in the vehicle and
the Engine Start/Stop button is ON,
but the vehicle cannot detect the
smart key.
In this case, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
7KLVLQGLFDWRUOLJKWEOLQNV
[When there is a malfunction with the
immobiliser system.
In this case, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
Turn signal indicator
light
7KLVLQGLFDWRUOLJKWEOLQNV
[When you operate the turn signals.
If any of the following occur, there may
be a malfunction with the turn signal
system.
- The turn signal indicator light
illuminates but does not blink
- The turn signal indicator light blinks
rapidly
- The turn signal indicator light does not
illuminate at all
If any of these conditions occur, we
recommend that you have your vehicle
inspected by a HYUNDAI authorised
repairer.
Low beam indicator light
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
When the headlamps are on.
High beam indicator light
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
[When the headlamps are on and in the
high beam position.
[When the turn signal lever is pulled
into the Flash-to-Pass position.

Page 114 of 649

4-19
04
High Beam Assist
indicator light (if
equipped)
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
When the high-beam is on with the light
switch in the AUTO position.
If your vehicle detects oncoming or
preceding vehicles, High Beam Assist
will switch the high beam to low beam
automatically.
For more details, refer to “High Beam
Assist (HBA)” section in chapter 5.
Light ON indicator light
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
When the tail lights is on.
Front fog indicator light
(if equipped)
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
When the front fog lights are on.
Rear fog indicator light
(if equipped)
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
When the rear fog lights are on.
Forward Safety warning
light (if equipped)
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
[When you set the ignition switch or
Engine Start/Stop button to the ON
position.
- The Forward Safety warning light
illuminates for approximately 3
seconds and then goes off.
[Whenever there is a malfunction with
Forward Collision-Avoidance Assist.
If this occurs, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
For more details, refer to “Forward
Collision-Avoidance Assist (FCA)”
section in chapter 7.
Lane Safety indicator
light (if equipped)
7KLVLQGLFDWRUOLJKWLOOXPLQDWHV
[[Green] When the function operating
conditions are satisfied.
[[White] The function operating
conditions are not satisfied.
[[Yellow] Whenever there is a
malfunction with Lane Keeping Assist.
If this occurs, we recommend that
you have the vehicle inspected by a
HYUNDAI authorised repairer.
For more details, refer to “Lane Keeping
Assist (LKA)” section in chapter 7.

Page 116 of 649

4-21
04
LCD display messages
Key not in vehicle
(for smart key system)
This warning message is displayed if the
smart key is not in the vehicle when you
open or close door in the ACC position
or ON position. The warning sound is
heard when you close door without a
smart key in vehicle.
When attempting to start the vehicle
always have the smart key with you.
Key not detected
(for smart key system)
This warning message is displayed if
the smart key is not detected when you
press the Engine Start/Stop button.
Press START button with key (for
smart key system)
This warning message is displayed if
you press the Engine Start/Stop button
whilst the warning message “Key not
detected” is displayed.
At this time, the immobiliser indicator
light blinks.
Low key battery
(for smart key system)
This warning message is displayed if the
battery of the smart key is discharged
whilst changing the Engine Start/Stop
button to the OFF position.
Press brake pedal to start engine
(for smart key system and
Automatic transmission/Dual clutch
transmission)
This warning message is displayed if the
Engine Start/Stop button changes to
the ACC position twice by pressing the
button repeatedly without depressing
the brake pedal.
You can start the vehicle by depressing
the brake pedal.
Press clutch pedal to start engine
(for smart key system and Manual
transmission)
This warning message is displayed if the
Engine Start/Stop button is in the ACC
position twice by pressing the button
repeatedly without depressing the clutch
pedal.
Depress the clutch pedal to start the
engine.
Press START button again
(for smart key system)
This message is displayed if you were
unable to start the vehicle when the
Engine Start/Stop button was pressed.
If this occurs, attempt to start the engine
by pressing the Engine Start/Stop button
again.
If the warning message appears each
time you press the Engine Start/Stop
button, we recommend that you have
your vehicle inspected by a HYUNDAI
authorised repairer.

Page 117 of 649

4-22
Instrument cluster
Shift to N to start engine
(for smart key system and
Automatic transmission/Dual clutch
transmission)
This warning message is displayed if
you try to start the engine with the shift
button not in the N (Neutral) position.
i Information
<RXFDQVWDUWWKHHQJLQHZLWKWKHVKLIW
OHYHULQWKH1 1HXWUDO SRVLWLRQ
Check BRAKE SWITCH fuse (for
smart key system and Automatic
transmission/Dual clutch
transmission)
This warning message is displayed if the
brake switch fuse is disconnected.
You need to replace the fuse with a new
one. If that is not possible, you can start
the engine by pressing the Engine Start/
Stop button for 10 seconds in the ACC
position.
Door, Bonnet, Tailgate open
indicator
OBC3040012
This warning is displayed if any door
or bonnet or tailgate is left open. The
warning will indicate which door is open
in the display.
CAUTION
Before driving the vehicle, you should
confirm that the door/bonnet/tailgate
is fully closed. Also, check there is no
door/bonnet/tailgate open warning
light or message displayed on the
instrument cluster.

Page 119 of 649

4-24
Instrument cluster
Low engine oil (if equipped)
This warning message is displayed when
the engine oil level should be checked.
If this warning message is displayed,
check the engine oil level as soon as
possible and add engine oil as required.
Slowly pour the recommended oil little
by little into a funnel.
Use only the specified engine oil. (Refer
to "Recommended lubricants and
capacities" section in chapter 2.)
Do not overfill the engine oil. Make sure
the oil level is not above F (Full) mark on
the dipstick.
NOTICE
If the message is displayed
continuously after adding the engine
oil and travelling approximately 31~
62 mile (50~100 km) after the engine
warms up, we recommend that the
system be checked by a HYUNDAI
authorised repairer.
Engine has overheated
(if equipped)
This warning message is displayed
when the engine coolant temperature
is above 120°C (248°F). This means that
the engine is overheated and may be
damaged.
If your vehicle is overheated, refer to
“Overheating” section in chapter 8.
Check headlight (if equipped)
This warning message is displayed if the
headlamps are not operating properly.
In addition, if a specific lamp(turn signal
lamp etc.) is not operating properly, the
warning message according to a specific
lamp (turn signal lamp etc.) is displayed.
A corresponding bulb may need to be
replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check brake light (if equipped)
This warning message is displayed if the
stop lamps are not operating properly. A
lamp may need to be replaced.
Make sure to replace the burned out
bulb with a new one of the same
wattage rating.
Check Active Air Flap system (if
equipped)
This message is displayed in the
following situations:
- There is a malfunction with the
actuator flap
- There is a malfunction with the
actuator air flap controller
- The air flap does not open
When all of the above conditions are
fixed, the warning will disappear.

Page 128 of 649

4-33
04
'RRU
ItemsExplanation
Automatically
lock[(QDEOHRQ6KLIW$OOGRRUVZLOOEHDXWRPDWLFDOO\ORFNHGLIWKHVKLIW
button is shifted from the P (Park) position to the R (Reverse), N
(Neutral), or D (Drive) position. (only when the engine is running.)
[(QDEOHRQ6SHHG$OOGRRUVZLOOEHDXWRPDWLFDOO\ORFNHGZKHQWKH
vehicle speed exceeds 9.3mph (15km/h).
[2II7KHDXWRGRRUORFNRSHUDWLRQZLOOEHGHDFWLYDWHG
Automatically
unlock[2Q6KLIWWR3$OOGRRUVZLOOEHDXWRPDWLFDOO\XQORFNHGLIWKHVKLIW
button is shifted to the P (Park) position. (only when the engine is
running.)
[2QNH\RXW2QYHKLFOHRII$OOGRRUVZLOOEHDXWRPDWLFDOO\XQORFNHG
when the ignition key is removed from the ignition switch or the
Engine Start/Stop button is set to the OFF position.
[2II7KHDXWRGRRUXQORFNRSHUDWLRQZLOOEHFDQFHOOHG
&RQYHQLHQFH
ItemsExplanation
Rear occupant
alertTo activate or deactivate the Rear Occupant Alert.
For more details, refer to "Rear Occupant Alert (ROA) system" in
chapter 5.
Welcome mirror[2QGRRUXQORFN7KHRXWVLGHUHDUYLHZPLUURUVDUHXQIROGHG
automatically when the doors are unlocked.
[2QGULYHUDSSURDFK7KHRXWVLGHUHDUYLHZPLUURUVDUHXQIROGHG
automatically when the vehicle is approached with the smart key.
For more details, refer to ''Welcome System'' in chapter 5.
Wireless
charging systemTo activate or deactivate the wireless charging system in the front seat.
For more details, refer to "Wireless cellular phone charging system" in
chapter 5.
Auto rear wiper
(in R)To activate or deactivate the Auto Rear Wiper function.If you move the
shift button from D to R when the front wiper operates, the rear wiper
will operate automatically. Then, if you move the shift button from R to
D, the rear wiper will stop.
Advanced anti-
theftTo activate or deactivate the Advanced Anti-Theft function.
Vehicle auto-
shut OffTo activate or deactivate the Vehicle Auto-Shut Off function.
Service interval[6HUYLFHLQWHUYDO
To activate or deactivate the service interval function.
[$GMXVWLQWHUYDO
If the service interval menu is activated, you may adjust the time and
distance.
[5HVHW
To reset the service interval.
❈ The information provided may differ depending on which functions are applicable
to your vehicle.

Page 131 of 649

4-36
Instrument cluster
Trip computer
The trip computer is a microcomputer-
controlled driver information system that
displays information related to driving.
i Information
6RPHGULYLQJLQIRUPDWLRQVWRUHGLQWKH
WULSFRPSXWHU IRUH[DPSOH$YHUDJH
9HKLFOH6SHHG UHVHWVLIWKHEDWWHU\LV
GLVFRQQHFWHG
Trip modes
Fuel Economy
[Average Fuel Economy
[Instant Fuel Economy

Accumulated Info
[Tripmeter
[Average Fuel Economy
[Elapsed Time

Drive Info
[Tripmeter
[Average Fuel Economy
[Elapsed Time

Auto Stop (if equipped)

Digital Speedometer
OBC3050050
To change the trip mode, toggle the
", " switch on the steering wheel.
Fuel economy
OIK047124N
$YHUDJH)XHO(FRQRP\ 
[The average fuel economy is
calculated by the total driving distance
and fuel consumption since the last
average fuel economy reset.
[The average fuel economy can be
reset both manually and automatically.

Page 133 of 649

4-38
Instrument cluster
The information is accumulated starting
from the last reset.
To manually reset the information, press
and hold the OK button when viewing
the accumulated driving info. The trip
distance, the average fuel economy,
and total driving time will reset
simultaneously.
The accumulated driving information
will continue to be counted whilst the
engine is still running (for example,
when the vehicle is in traffic or stopped
at a stop light).
i Information
7KHYHKLFOHPXVWEHGULYHQIRUD
PLQLPXPRIPHWHUV PLOHV 
VLQFHWKHODVWLJQLWLRQNH\F\FOHZLOOEH
UHFDOFXODWHG
Drive Info display
„Type A
OJX1040011E
„Type B
OJX1040065E
This display shows the accumulated trip
distance (1), the average fuel economy
(2), and the total driving time (3).

Page 134 of 649

4-39
04
The information is combined for each
ignition cycle. However, when the
engine has been OFF for 4 hours or
longer the Drive Info screen will reset.
To manually reset the information, press
and hold the OK button when viewing
the Drive Info. The trip distance, the
average fuel economy, and total driving
time will reset simultaneously.
The driving information will continue
to be counted whilst the engine is still
running (for example, when the vehicle
is in traffic or stopped at a stop light.)
i Information
7KHYHKLFOHPXVWEHGULYHQIRUD
PLQLPXPRIPHWHUV PLOHV 
VLQFHWKHODVWLJQLWLRQNH\F\FOHZLOOEH
UHFDOFXODWHG
Digital speedometer
OJX1040018E
This message shows the speed of the
vehicle (km/h, MPH).
OJX1069044
$XWRVWRS LIHTXLSSHG
AUTO STOP display shows the elapsed
time of engine stop by Idle Stop and Go
system.
For more details, refer to “Idle Stop and
Go (ISG)” section in chapter 6.

Page 138 of 649

4-43
04
„Type A
OJX1040012E/OJX1040067E
„Type B
$FFXPXODWHGLQIR
Accumulated trip distance (1), average
fuel economy (2), and total driving time
(3) are displayed.
The information is accumulated starting
from the last reset.
To reset manually, press the OK switch
on the steering wheel for more than
1 second when ‘Accumulated Info’ is
displayed.
OJX1040018E
'LJLWDOVSHHGRPHWHU
Digital speedometer display shows the
speed of the vehicle.
OBC3070068
$WWHQWLRQOHYHO LIHTXLSSHG
The driver’s attention level is shown
based on the driver’s driving pattern.
For more details, refer to "Driver
Attention Warning (DAW)“ section in
chapter 7.
OJX1069044
$XWRVWRS LIHTXLSSHG
AUTO STOP display shows the elapsed
time of engine stop by Idle Stop and Go
system.
For more details, refer to “Idle Stop and
Go (ISG)” section in chapter 6.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 ... 130 next >