snow chains HYUNDAI I20 2023 Owners Manual

6-37
06
Parking brake warning light
Check the Parking Brake
Warning Light by placing the
ignition switch to the ON
position (do not start the
engine).
This light will illuminate when the
parking brake is applied with the ignition
switch in the START or ON position.
Before driving, be sure the parking brake
is released and the Brake Warning Light
is OFF.
If the Parking Brake Warning Light
remains on after the parking brake is
released whilst the engine is running,
there may be a malfunction in the
brake system. Immediate attention is
necessary.
If at all possible, cease driving the
vehicle immediately. If that is not
possible, use extreme caution whilst
operating the vehicle and only continue
to drive the vehicle until you can reach a
safe location.
Anti-lock Brake System (ABS)
WARNING
An Anti-Lock Braking System (ABS) or
an Electronic Stability Control (ESC)
system will not prevent accidents
due to improper or dangerous driving
manoeuvres. Even though vehicle
control is improved during emergency
braking, always maintain a safe
distance between you and objects
ahead of you. Vehicle speeds should
always be reduced during extreme
road conditions. The braking distance
for vehicles equipped with ABS or ESC
may be longer than for those without
these systems in the following road
conditions.
Drive your vehicle at reduced speeds
during the following conditions:

[Rough, gravel or snow-covered
roads.

[On roads where the road surface is
pitted or has different surface height.

[Tyre chains are installed on your
vehicle.
The safety features of an ABS or ESC
equipped vehicle should not be tested
by high speed driving or cornering. This
could endanger the safety of yourself
or others.
ABS is an electronic braking system that
helps prevent a braking skid. ABS allows
the driver to steer and brake at the same
time.

6-58
Driving your vehicle
Hazardous driving conditions
When hazardous driving elements are
encountered such as water, snow,
ice, mud and sand, take the following
precautions:

[Drive cautiously and maintain a longer
braking distance.

[Avoid abrupt braking or steering.

[When your vehicle is stuck in snow,
mud, or sand, use the second
gear. Accelerate slowly to avoid
unnecessary wheel spin.

[Put sand, rock salt, tyre chains or
other non-slip materials under the
wheels to provide additional traction
whilst the vehicle becomes stuck in
ice, snow, or mud.
WARNING
Downshifting with an Automatic
transmission, whilst driving on slippery
surfaces can cause an accident. The
sudden change in tyre speed could
cause the tyres to skid. Be careful when
downshifting on slippery surfaces.
Rocking the vehicle
If it is necessary to rock the vehicle to
free it from snow, sand, or mud, first
turn the steering wheel right and left to
clear the area around your front wheels.
Then, shift back and forth between the
1st gear and R (Reverse, for manual
transmission vehicle) or R (Reverse)
and a forward gear (for Automatic
transmission vehicle/Dual clutch
transmission vehicle).
Try to avoid spinning the wheels, and do
not race the engine.
To prevent transmission wear, wait until
the wheels stop spinning before shifting
gears. Release the accelerator pedal
whilst shifting, and press lightly on the
accelerator pedal whilst the transmission
is in gear. Slowly spinning the wheels in
forward and reverse directions causes
a rocking motion that may free the
vehicle.
WARNING
If the vehicle is stuck and excessive
wheel spin occurs, the temperature
in the tyres can increase very quickly.
If the tyres become damaged, a tyre
blow out or tyre explosion can occur.
This condition is dangerous - you and
others may be injured. Do not attempt
this procedure if people or objects are
anywhere near the vehicle.
If you attempt to free the vehicle, the
vehicle can overheat quickly, possibly
causing an engine compartment fire or
other damages. Try to avoid spinning
the wheels as much as possible to
prevent overheating of either the tyres
or the engine. DO NOT allow the vehicle
to spin the wheels above 35 mph (56
km/h).
i Information
7KH(6&V\VWHPLIHTXLSSHGPXVWEH
WXUQHG2))EHIRUHURFNLQJWKHYHKLFOH
63(&,$/'5,9,1*&21',7,216

6-61
06
The severe weather conditions of winter
quickly wear out tyres and cause other
problems. To minimise winter driving
problems, you should take the following
suggestions:
Snow or icy conditions
You need to keep sufficient distance
between your vehicle and the vehicle in
front of you.
Apply the brakes gently. Speeding, rapid
acceleration, sudden brake applications,
and sharp turns are potentially
very hazardous practices. During
deceleration, use engine braking to the
fullest extent. Sudden brake applications
on snowy or icy roads may cause the
vehicle to skid.
To drive your vehicle in deep snow, it
may be necessary to use snow tyres or
to install tyre chains on your tyres.
Always carry emergency equipment.
Some of the items you may want to
carry include tyre chains, tow straps or
chains, a flashlight, emergency flares,
sand, a shovel, jumper cables, a window
scraper, gloves, ground cloth, coveralls,
a blanket, etc.
Snow tyres
WARNING
Snow tyres should be equivalent
in size and type to the vehicle’s
standard tyres. Otherwise, the safety
and handling of your vehicle may be
adversely affected.
If you mount snow tyres on your vehicle,
make sure to use radial tyres of the same
size and load range as the original tyres.
Mount snow tyres on all four wheels
to balance your vehicle’s handling in
all weather conditions. The traction
provided by snow tyres on dry roads
may not be as high as your vehicle’s
original equipment tyres. Check with
the tyre dealer for maximum speed
recommendations.
i Information
'RQRWLQVWDOOVWXGGHGW\UHVZLWKRXWILUVW
FKHFNLQJORFDODQGPXQLFLSDOUHJXODWLRQV
IRUSRVVLEOHUHVWULFWLRQVDJDLQVWWKHLUXVH
WINTER DRIVING

6-62
Driving your vehicle
Tyre chains
OBC3060010
Since the sidewalls of radial tyres are
thinner than other types of tyres, they
may be damaged by mounting some
types of tyre chains on them. Therefore,
the use of snow tyres is recommended
instead of tyre chains. Do not mount
tyre chains on vehicles equipped with
aluminium wheels; if unavoidable use a
wire type chain. If tyre chains must be
used, use genuine HYUNDAI parts and
install the tyre chain after reviewing
the instructions provided with the tyre
chains. Damage to your vehicle caused
by improper tyre chain use is not
covered by your vehicle manufacturer’s
warranty.
NOTICE
If your vehicle has 215/45R17 or
205/55R17 size tyres do not use tyre
chain; they can damage your vehicle
(wheel, suspension and body).
WARNING
The use of tyre chains may adversely
affect vehicle handling:

[Drive less than 20 mph (30 km/h)
or the chain manufacturer’s
recommended speed limit,
whichever is lower.

[Drive carefully and avoid bumps,
holes, sharp turns, and other road
hazards, which may cause the vehicle
to bounce.

[Avoid sharp turns or locked wheel
braking.
i Information

6-63
06
&KDLQ,QVWDOODWLRQ
When installing tyre chains, follow the
manufacturer’s instructions and mount
them as tightly possible. Drive slowly
(less than 20 mph (30 km/h)) with
chains installed. If you hear the chains
contacting the body or chassis, stop and
tighten them. If they still make contact,
slow down until the noise stops. Remove
the tyre chains as soon as you begin
driving on cleared roads.
When mounting snow chains, park
the vehicle on level ground away from
traffic. Turn on the vehicle Hazard
Warning Flasher and place a triangular
emergency warning device behind the
vehicle (if available). Always place the
vehicle in P (Park), apply the parking
brake and turn off the engine before
installing snow chains.
NOTICE
When using tyre chains:

[Wrong size chains or improperly
installed chains can damage your
vehicle’s brake lines, suspension,
body and wheels.

[Use SAE “S” class or wire chains.

[If you hear noise caused by chains
contacting the body, retighten the
chain to prevent contact with the
vehicle body.

[To prevent body damage, retighten
the chains after driving 0.3~0.6 miles
(0.5~1.0 km).

[Do not use tyre chains on vehicles
equipped with aluminium wheels. If
unavoidable, use a wire type chain.

[Use wire chains less than 0.47 in (12
mm) wide to prevent damage to the
chain’s connection.
Winter Precautions
Use high quality ethylene glycol coolant
Your vehicle is delivered with high
quality ethylene glycol coolant in the
cooling system. It is the only type of
coolant that should be used because it
helps prevent corrosion in the cooling
system, lubricates the water pump and
prevents freezing. Be sure to replace or
replenish your coolant in accordance
with the maintenance schedule. Before
winter, have your coolant tested to
assure that its freezing point is sufficient
for the temperatures anticipated during
the winter.
Check battery and cables
Winter temperatures affect battery
performance. Inspect the battery and
cables, as specified in the chapter
9. The battery charging level can be
checked by a HYUNDAI authorised
repairer or in a service station.
Change to “winter weight” oil if
necessary
In some regions during winter, it is
recommended to use the “winter
weight” oil with lower viscosity. For
further information, refer to the chapter
2. When you are not sure about a type
of winter weight oil, consult a HYUNDAI
authorised repairer.

6-64
Driving your vehicle
Check spark plugs and ignition system
Inspect the spark plugs, as specified
in the chapter 9. If necessary, replace
them. Also check all ignition wirings and
components for any cracks, wear-out,
and damage.
To prevent locks from freezing
To prevent the locks from being frozen,
spray approved de-icing fluid or glycerin
into key holes. When a lock opening is
already covered with ice, spray approved
de-icing fluid over the ice to remove it.
When an internal part of a lock freezes,
try to thaw it with a heated key. Carefully
use the heated key to avoid an injury.
Use approved window washer anti-
freeze solution in system
To prevent the window washer from
being frozen, add authorised window
washer anti-freeze solution, as specified
on the window washer container.
Window washer anti-freeze solution is
available from a HYUNDAI authorised
repairer, and most vehicle accessory
outlets. Do not use engine coolant or
other types of anti-freeze solution to
prevent any damage to the vehicle paint.
Do not let your parking brake freeze
Under some conditions your parking
brake can freeze in the engaged
position.
This is most likely to happen when
there is an accumulation of snow or
ice around or near the rear brakes or if
the brakes are wet. When there is the
risk that your parking brake may freeze,
temporarily apply it with the shift lever
in N (for Automatic Transmission/Dual
clutch transmission) or in the 1st gear or
reverse gear (for Manual transmission).
Also, block the rear wheels in advance,
so the vehicle may not roll. Then, release
the parking brake.Do not let ice and snow accumulate
underneath
Under some conditions, snow and ice
can build up under the fenders and
interfere with the steering. When driving
in such conditions during the severe
winter, you should check underneath
the vehicle on a regular basis, to ensure
that the front wheels and the steering
components is unblocked.
Carry emergency equipment
In accordance with weather conditions,
you should carry appropriate emergency
equipment, whilst driving. Some of the
items you may want to carry include tyre
chains, tow straps or chains, flashlight,
emergency flares, sand, shovel, jumper
cables, window scraper, gloves, ground
cloth, coveralls, blanket, etc.
Do not place objects or materials in the
engine compartment
Putting objects or materials in the
engine compartment may cause an
engine failure or combustion, because
they may block the engine cooling.
Such damage will not be covered by the
manufacturer’s warranty.

07
7-137
WARNING

[Reverse Parking Distance Warning
is a supplemental function. The
operation of the function can be
affected by several factors (including
environmental conditions). It is the
responsibility of the driver to always
check the rear view before and whilst
parking.

[Your new vehicle warranty does not
cover any accidents or damage to
the vehicle due to the malfunction of
Reverse Parking Distance Warning.

[Pay close attention when driving near
objects, pedestrians, and especially
children. Some objects may not be
detected by the ultrasonic sensors,
due to the objects distance, size or
material, all of which can limit the
effectiveness of the sensor.
Limitations of Reverse Parking
Distance Warning

[Reverse Parking Distance Warning
may not operate normally when:
- Moisture is fTrozen to the sensor
- Sensor is covered with foreign
material, such as snow or water (The
function will operate normally when
such foreign material are removed.)
- The weather is extremely hot or cold
- The sensor or sensor assembly is
disassembled
- The surface of the sensor is pressed
hard or an impact is applied with a
hard object
- The surface of the sensor is
scratched with a sharp object
- The sensors or its surrounding area is
directly sprayed with high pressure
washer
[Reverse Parking Distance Warning
may malfunction when:
- Heavy rain or water spray is present
- Water flows on the surface of the
sensor
 $IIHFWHGE\DQRWKHUYHKLFOH
TVVHQVRUV
- The sensor is covered with snow
- Driving on uneven road, gravel roads
or bushes
- Objects that generates ultrasonic
waves are near the sensor
- Installing the license plate differently
from the original location
- The vehicle bumper height or
ultrasonic sensor installation has
been modified
- Attaching equipments or accessories
around the ultrasonic sensors

[The following objects may not be
detected:
- Sharp or slim objects, such as ropes,
chains or small poles.
- Objects, which tend to absorb sensor
frequency, such as clothes, spongy
material or snow.
- Objects smaller than 100 cm (40 in.)
in length and narrower than 14 cm (6
in.) in diameter.
- Pedestrians, animals or objects
that are very close to the ultrasonic
sensors

[ Parking Distance Warning Indicators
may be displayed differently from
the actual detected location when
the obstacle is located between the
sensors.

[Parking Distance Warning indicator
may not occur sequentially depending
on vehicle speed or obstacle shape.

[If Reverse Parking Distance Warning
needs repair, we recommend that the
function be inspected by a HYUNDAI
authorised repairer.

Driver assistance system
7-142
Limitations of Forward/Reverse
Parking Distance Warning

[Forward/Reverse Parking Distance
Warning may not operate normally
when:
- Moisture is frozen to the sensor
- Sensor is covered with foreign
material, such as snow or water (The
function will operate normally when
such foreign material are removed.)
- The weather is extremely hot or cold
- The sensor or sensor assembly is
disassembled
- The surface of the sensor is pressed
hard or an impact is applied with a
hard object
- The surface of the sensor is
scratched with a sharp object
- The sensors or its surrounding area is
directly sprayed with high pressure
washer

[Forward/Reverse Parking Distance
Warning may malfunction when:
- Heavy rain or water spray is present
- Water flows on the surface of the
sensor
 $IIHFWHGE\DQRWKHUYHKLFOH
TVVHQVRUV
- The sensor is covered with snow
- Driving on uneven road, gravel roads
or bushes
- Objects that generates ultrasonic
waves are near the sensor
- Installing the license plate differently
from the original location
- The vehicle bumper height or
ultrasonic sensor installation has
been modified
- Attaching equipments or accessories
around the ultrasonic sensors
[The following objects may not be
detected:
- Sharp or slim objects, such as ropes,
chains or small poles.
- Objects, which tend to absorb sensor
frequency, such as clothes, spongy
material or snow.
- Objects smaller than 100 cm (40 in.)
in length and narrower than 14 cm (6
in.) in diameter.
- Pedestrians, animals or objects
that are very close to the ultrasonic
sensors

[Parking Distance Warning Indicators
may be displayed differently from
the actual detected location when
the obstacle is located between the
sensors.

[Parking Distance Warning indicator
may not occur sequentially depending
on vehicle speed or obstacle shape.

[ If Forward/Reverse Parking Distance
Warning needs repair, we recommend
that the function be inspected by a
HYUNDAI authorised repairer.

07
7-165
[There is a circular pillar or narrow
pillar, or a pillar surrounded by objects
such as fire extinguisher, etc. near the
parking space

[The road surface is bumpy (curbstone,
speed bump, etc.)

[The road is slippery

[The parking space is near a vehicle
with higher ground clearance or big,
such as a truck, etc.

[The parking space is Inclined

[There is heavy wind

[Operating the function on uneven
roads, gravel roads, bushes, etc.

[The performance of the ultrasonic
sensor is affected by extremely hot or
cold weather

[The ultrasonic sensor is covered with
snow or water

[An object that generates ultrasonic
waves is nearby

[Wireless transmitters or mobile
phones are present near the sensor

[Your vehicle is affected by another
YHKLFOH
TV3DUNLQJ'LVWDQFH:DUQLQJ

[The sensor is mounted or positioned
incorrectly by an impact to the
bumper

[When the ultrasonic sensor cannot
detect the following objects:
- Sharp or slim objects such as ropes,
chains or small poles
- Objects smaller than 100 cm (40 in.)
in length and narrower than 14 cm (6
in.) in diameter
- Objects which tend to absorb sensor
frequency such as clothes, spongy
material or snowParking Assist may not operate normally
under the following circumstances:

[Parking on inclines
OBC3070082TU
Park manually when parking on
inclines.

[Parking in snow
OBC3070083TU
Snow may interfere with sensor
operation, or Parking Assist may
cancel if the road is slippery whilst
parking.

8-14
Emergency situations
TPMS (Tyre Pressure
Monitoring System)
malfunction indicator
The TPMS Malfunction Indicator
will illuminate after it blinks for
approximately one minute when there
is a problem with the Tyre Pressure
Monitoring System.
We recommend that you have the
system checked by a HYUNDAI
authorised repairer as soon as possible.
NOTICE
If there is a malfunction with the TPMS,
the Low Tyre Pressure Position Telltale
will not be displayed even though the
vehicle has an under-inflated tyre.
NOTICE
The TPMS Malfunction Indicator may
illuminate after blinking for one minute
if the vehicle is near electric power
supply cables or radio transmitters
such as police stations, government
and public offices, broadcasting
stations, military installations, airports,
transmitting towers, etc.
Additionally, the TPMS Malfunction
Indicator may illuminate if snow chains
are used or electronic devices such as
computers, chargers, remote starters,
navigation, etc. This may interfere with
normal operation of the TPMS.
Changing a tyre with TPMS
If you have a flat tyre, the Low Tyre
Pressure and Position telltales will come
on. We recommend that you have
the flat tyre repaired by a HYUNDAI
authorised repairer as soon as possible
or replace the flat tyre with the spare
tyre.
NOTICE
It is recommended that you do not
use a puncture-repairing agent not
approved by HYUNDAI dealer or the
equivalent specified for your vehicle
to repair and/or inflate a low pressure
tyre. Tyre sealant not approved by
HYUNDAI dealer or the equivalent
specified for your vehicle may damage
the tyre pressure sensor.
The spare tyre (if equipped) does not
come with a tyre pressure monitoring
sensor. When the low pressure tyre or
the flat tyre is replaced with the spare
tyre, the Low Tyre Pressure Telltale will
remain on. Also, the TPMS Malfunction
Indicator will illuminate after blinking
for one minute if the vehicle is driven
at speed above 15.5 mph (25 km/h) for
approximately 10 minutes.
Once the original wheel equipped with
a tyre pressure monitoring sensor is
reinflated to the recommended pressure
and reinstalled on the vehicle, the
Low Tyre Pressure Telltale and TPMS
Malfunction Indicator will go off within a
few minutes of driving.
❈ All vehicles sold in the EUROPE
market during below period must be
equipped with TPMS.
- New model vehicle : Nov. 1, 2012 ~
- Current model vehicle : Nov. 1, 2014~
(Based on vehicle registrations)