display HYUNDAI KONA 2023 Workshop Manual

Page 271 of 478

Driving your vehicle6-46
Shift Light
„N mode
OCN7N061248N
When engine is operating in a high
RPM area, it is indicated on the cluster
according to the corresponding engine
RPM.
As the engine RPM approaches to the
limit, each of shift lights on both sides,
and when all lights blinks in red or alert
alarm sound, it is time to perform up-
shift immediately.
In the “Shift light” tab of the
performance option, you can set which
mode displays shift light and select
target shift RPM.
1PRGH

Page 273 of 478

Driving your vehicle6-48
Operating condition
[ N Track Sense Shift is enabled in the
Performance Options settings
[ Shift lever in D (Drive) position
[ Transmission mode is SPORT or
SPORT+ (Including SPORT or N Riding
Mode)
[ Vehicle speed is above 21 mph
(35km/h)
[ Cornering-oriented dynamic driving
detection
OJSN050190

à When N Track Sense Shift is operating,
a message is displayed in the
instrument cluster LCD screen as
shown below.
Non-operating conditions
[N Track Sense Shift is disabled in
Performance Options settings
[ Shift lever position is in P/R/N
[ Changing Transmission mode during
operation (Transmission mode does
not work in ECO, NORMAL or manual
shift mode.)
[ Cruise Control and Smart Cruise
Control is operating
[ Vehicle speed is below 21 mph (35
km/h)

à When N Track Sense Shift is
deactivated, the displayed message
will disappear from the instrument
LCD screen.
CAUTION
Vehicle safety and control must be at
your own discretion and do not attempt
to drive dangerously to operate N Track
Sense Shift.
WARNING
N Track Sense is activated only
automatically when vehicle recognizes
dynamic driving (longitudinal & lateral
forces). To activate, you must push the
vehicle to the limits.

Page 296 of 478

Driver Assistance System7-6
OTM070059L
Stopping vehicle and ending brake control
[ When the v
ehicle is stopped due
to emergency braking, the ‘Drive
FDUHIXOO\TZDUQLQJPHVVDJHZLOO
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
WARNING
Take the following precautions when
using Forward Collision-Avoidance
Assist:
[For your safety, change the Settings
after parking the vehicle at a safe
location.
[ With ‘Active Assist’ or ‘Warning Only’
selected, when ESC is turned off by
pressing and holding the ESC OFF
button, Forward Collision-Avoidance
Assist will turn off automatically.
In this case, Forward Collision-
Avoidance Assist cannot be set
from the Settings menu and the

warning light will illuminate on the
cluster which is normal. If ESC is
turned on by pressing the ESC OFF
button, Forward Collision-Avoidance
Assist will maintain the last setting. [
Forward Collision-Avoidance Assist
does not operate in all situations or
cannot avoid all collisions.
[ The driver should hold the
responsibility to control the vehicle.
Do not solely depend on Forward
Collision-Avoidance Assist. Rather,
maintain a safe braking distance,
and, if necessary, depress the brake
pedal to reduce driving speed or to
stop the vehicle.
[ Never deliberately operate Forward
Collision-Avoidance Assist on people,
objects, etc. It may cause serious
injury or death.
[ Forward Collision-Avoidance
Assist may not operate if the driver
depresses the brake pedal to avoid
collision.
[ Depending on the road and driving
conditions, Forward Collision-
Avoidance Assist may warn the driver
late or may not warn the driver.
[ During Forward Collision-Avoidance
Assist operation the vehicle may
stop suddenly injuring passengers
and shifting loose objects. Always
have the seat belt on and keep loose
objects secured.
[ If any other function’s warning
message is displayed or audible
warning is generated, Forward
Collision-Avoidance Assist warning
message may not be displayed
and audible warning may not be
generated.
[ You may not hear the warning sound
of Forward Collision-Avoidance
Assist if the surrounding is noisy.
[ Forward Collision-Avoidance
Assist may turn off or may not
operate properly or may operate
unnecessarily depending on the road
conditions and the surroundings.

Page 309 of 478

07
7-19
Information
For more details on the limitations of the
front view camera, refer to “Forward
Collision-Avoidance Assist (FCA)” section
in chapter 7.
WARNING
Take the following precautions when
using Lane Keeping Assist:
[The driver should hold the
responsibility to safely drive and
control the vehicle. Do not solely rely
on Lane Keeping Assist and drive
dangerously.
[ The operation of Lane Keeping
Assist can be cancelled or not
work properly depending on road
conditions and surroundings. Always
be cautious while driving.
[ Refer to “Limitations of Lane Keeping
Assist” if the lane is not detected
properly.
[ When you are towing a trailer or
another vehicle, we recommend that
Lane Keeping Assist is turned off due
to safety reasons.
[ If the vehicle is driven at high speed,
the steering wheel will not be
controlled. The driver must always
follow the speed limit when using
Lane Keeping Assist. [
If any other system’s warning
message is displayed or audible
warning is generated, Lane Keeping
Assist warning message may not be
displayed and audible warning may
not be generated.
[ You may not hear the warning
sound of Lane Keeping Assist if the
surrounding is noisy.
[ If you attach objects to the steering
wheel, steering may not be assisted
properly.
[ Lane Keeping Assist may not operate
for 15 seconds after the vehicle is
started, or the front view camera is
initialized.
[ Lane Keeping Assist will not operate
when:
- The turn signal or hazard warning
flasher is turned on
- The vehicle is not driven in the
center of the lane when Lane
Keeping Assist is turned on or right
after changing a lane
- ESC (Electronic Stability Control)
or VSM (Vehicle Stability
Management) is activated
- The vehicle is driven on a sharp
curve
- The vehicle speed is below 35 mph
(55 km/h) or above 130 mph (210
km/h)
- The vehicle makes sharp lane
changes
- The vehicle brakes suddenly

Page 315 of 478

07
7-25
Collision warning
[Collision W
arning will operate when
the turn signal is turned on in the
direction of the detected vehicle.
[ ,IS:DUQLQJ2QO\TLVVHOHFWHGIURPWKH Settings menu, the collision warning
will operate when your vehicle
approaches the lane the blind spot
vehicle is detected.
[ To warn the driver of a collision, the
warning light on the side view mirror
and head-up display (if equipped) will
blink. At the same time, an audible
warning will sound.
[ When the turn signal is turned off or
you move away from the lane, the
collision warning will be canceled and
Blind-Spot Collision-Avoidance Assist
will return to vehicle detection state.
WARNING
[The detecting range of the rear
corner radar is determined by a
standard road width, therefore, on
a narrow road, Blind-Spot Collision-
Avoidance Assist may detect other
vehicles two lanes over and warn
you. In contrast, on a wide road,
Blind-Spot Collision-Avoidance
Assist may not be able to detect a
vehicle driving in the next lane and
may not warn you.
[ When the hazard warning flasher is
on, the collision warning by the turn
signal will not operate.
Information
[If the driver's seat is on the left side, the
collision warning may occur when you
turn left. Maintain a proper distance
with the vehicles in the left lane. If the
driver's seat is on the right side, the
collision warning may occur when you
turn right. Maintain a proper distance
with the vehicles in the right lane.
[ Images or colors may appear
differently depending on the instrument
panel specifications or theme.
OOSN071005L
Collision-avoidance assist (while driving)
[T
o warn the driver of a collision, the
warning light on the side view mirror
will blink and a warning message will
appear on the cluster. At the same
time, an audible warning will sound,
warning light on the head-up display
(if equipped) will blink.
[ Blind-Spot Collision-Avoidance Assist
will operate when your vehicle speed
is between 40-120 mph (60-200 km/h)
and both lane markings of the driving
lane are detected.
[ Emergency Braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.

Page 316 of 478

Driver Assistance System7-26
WARNING
[ Collision-avoidance assist will
be canceled under the following
circumstances:
- Your vehicle enters the next lane
by a certain distance
- Your vehicle is away from the
collision risk
- The steering wheel is sharply
steered
- The brake pedal is depressed
- Forward Collision-Avoidance Assist
is operating
[ After Blind-Spot Collision-Avoidance
Assist operation or lane change,
you must drive to the center of the
lane. Blind-Spot Collision-Avoidance
Assist will not operate if the vehicle is
not driven in the center of the lane.
OOSN071006L
Collision-avoidance assist (while
departing)
[T
o warn the driver of a collision, the
warning light on the side view mirror
will blink and a warning message
will appear on the cluster. At the
same time, an audible warning will
sound, warning light on the head-up
display (if equipped) will blink and the
steering wheel will vibrate.
[ Blind-Spot Collision-Avoidance Assist
will operate when your vehicle speed
is below 2 mph (3 km/h) and the
speed of the vehicle in the blind spot
area is above 3 mph (5 km/h).
[ Emergency Braking will be assisted to
help prevent collision with the vehicle
in the blind spot area.

Page 317 of 478

07
7-27
OOSN071018L
Stopping vehicle and ending brake control
[When the v
ehicle is stopped due
to emergency braking, the ‘Drive
FDUHIXOO\TZDUQLQJPHVVDJHZLOO
appear on the cluster.
For your safety, the driver should
depress the brake pedal immediately
and check the surroundings.
[ Brake control will end after the vehicle
is stopped by emergency braking for
approximately 2 seconds.
WARNING
Take the following precautions when
using Blind-Spot Collision-Avoidance
Assist:
[For your safety, change the Settings
after parking the vehicle at a safe
location.
[ If any other system’s warning
message is displayed or audible
warning is generated, Blind-Spot
Collision-Avoidance Assist’s warning
message may not be displayed
and audible warning may not be
generated.
[ You may not hear the warning sound
of Blind-Spot Collision-Avoidance
Assist if the surrounding is noisy. [
Blind-Spot Collision-Avoidance
Assist may not operate if the driver
applies the brake pedal to avoid
collision.
[ When Blind-Spot Collision-Avoidance
Assist is operating, braking control
by the function will automatically
cancel when the driver excessively
depresses the accelerator pedal or
sharply steers the vehicle.
[ During Blind-Spot Collision-
Avoidance Assist operation, the
vehicle may stop suddenly injuring
passengers and shifting loose
objects. Always have the seat belt on
and keep loose objects secured.
[ Even if there is a problem with Blind-
Spot Collision-Avoidance Assist, the
vehicle’s basic braking performance
will operate properly.
[ Blind-Spot Collision-Avoidance Assist
does not operate in all situations or
cannot avoid all collisions.
[ Blind-Spot Collision-Avoidance
Assist may warn the driver late or
may not warn the driver depending
on the road and driving conditions.
[ Driver should maintain control of the
vehicle at all times. Do not depend
on Blind-Spot Collision-Avoidance
Assist. Maintain a safe braking
distance, and if necessary, depress
the brake pedal to reduce driving
speed or to stop the vehicle.
[ Never operate Blind-Spot Collision-
Avoidance Assist on people, animal,
objects, etc. It may cause serious
injury or death.

Page 326 of 478

Driver Assistance System7-36
WARNING
Take the following precautions when
using Safe Exit Warning:
[ For your safety, change the Settings
after parking the vehicle at a safe
location.
[ If any other system’s warning
message is displayed or audible
warning is generated, Safe Exit
Warning's warning message may not
be displayed and audible warning
may not be generated.
[ You may not hear the warning
sound of Safe Exit Warning if the
surrounding is noisy.
[ Safe Exit Warning does not operate
in all situations or cannot prevent all
collisions.
[ Safe Exit Warning may warn the
driver late or may not warn the driver
depending on the road and driving
conditions. Always check vehicle
surroundings.
[ The driver and passengers are
responsible for accidents that occurs
while exiting the vehicle. Always
check the surroundings before you
exit the vehicle.
[ Never deliberately operate Safe
Exit Warning. Doing so may lead to
serious injury or death.
[ Safe Exit Warning does not operate
if there is a problem with Blind- Spot
Collision-Avoidance Assist. The
warning message of Blind- Spot
Collision-Avoidance Assist will
appear when:
- Blind- Spot Collision-Avoidance
Assist sensor or the sensor
surrounding is polluted or covered
- Blind- Spot Collision-Avoidance
Assist fails to warn passengers or
falsely warn passengers
- Blind- Spot Collision-Avoidance
Assist warning light appears
Information
[ After the engine is turned off, Safe Exit
Warning operates approximately for 3
minutes, but turns off immediately if
the doors are locked.
[ Images or colors may appear
differently depending on the instrument
panel specifications or theme.
Safe Exit Warning Malfunction
and Limitations
Safe Exit Warning malfunction
OTM070099N
When Safe Exit Warning is not working
properly, the ‘Check Blind-Spot Safety
V\VWHPTZDUQLQJPHVVDJHZLOODSSHDURQ
the cluster for several seconds, and the
master (
) warning light will illuminate
on the cluster. If the master warning light
illuminates, have the vehicle inspected
by an authorized HYUNDAI dealer.

Page 331 of 478

07
7-41
Driver Attention Warning
Operation
Basic function
Display and warning
The basic function of Driver Attention
W
arning is to inform the driver of their
S$WWHQWLRQ/HYHOTDQGWRZDUQWKHGULYHUWR
S&RQVLGHUWDNLQJDEUHDNT
Attention Level
„Function off „Standby/Disabled
OTM070102NOOSN071082N
„Attentive driving„Inattentive driving
OOSN071078NOOSN071083N
[The driver can monitor his/her driving
conditions on the cluster.

- When the ‘Inattentive Driving
:DUQLQJTLVGHVHOHFWHGIURPWKH
6HWWLQJVPHQXS6\VWHP2IITLV
displayed.
- Driver Attention Warning will operate when the vehicle speed is
between 0-130 mph (0-210 km/h).
- When the vehicle speed is not within the operating speed,
WKHPHVVDJHS6WDQGE\TZLOOEH
displayed. [ 7KHGULYHUTVDWWHQWLRQOHYHOLVGLVSOD\HG
on the scale of 1 to 5. The lower the
level is, the more inattentive the driver
is.
[ The level decreases when the driver
does not take a break for a certain
period of time.
Taking a break
OTM070105L
[ 7KHS&RQVLGHUWDNLQJDEUHDNTPHVVDJH will appear on the cluster and an
audible warning will sound to suggest
that the driver take a break, when the
GULYHUTVDWWHQWLRQOHYHOLVEHORZ
[ Driver Attention Warning will not
suggest a break when the total driving
time is shorter than 10 minutes or 10
minutes has not passed after the last
break was suggested.
WARNING
For your safety, change the Settings
after parking the vehicle at a safe
location.

Page 332 of 478

Driver Assistance System7-42
CAUTION
[ Driver Attention Warning may
suggest a break depending on the
driver’s driving pattern or habits,
even if the driver doesn’t feel
fatigued.
[ Driver Attention Warning is a
supplemental function and may not
be able to determine whether the
driver is inattentive.
[ The driver who feels fatigued should
take a break at a safe location, even
though there is no break suggestion
by Driver Attention Warning.
Information
[For more details on setting the
functions in the infotainment system
Vehicle Settings, refer to “Vehicle
Settings” section in chapter 4.
[ Driver Attention Warning will reset the
last break time to 0:00 in the following
situations:
- The engine is turned off
- The driver unfastens the seat belt
and opens the driver’s door
- The vehicle is stopped for more than
10 minutes
- When the driver resets Driver
Attention Warning, the last break
time is set to 0:00 and the driver’s
attention level is set to High.
Leading Vehicle Departure Alert
function
OOSN071023L
When a detected vehicle in front departs
from a stop, Leading Vehicle Departure
Alert will inform the driver by displaying
WKHS/HDGLQJYHKLFOHLVGULYLQJDZD\T
message on the cluster and an audible
warning will sound.
WARNING
[ If any other system’s warning
message is displayed or audible
warning is generated, Driver
Attention Warning message may not
be displayed and audible warning
may not be generated.
[ The driver should hold the
responsibility to safely drive and
control the vehicle.
CAUTION
[Leading Vehicle Departure Alert is a
supplemental function and may not
alert the driver whenever the front
vehicle departs from a stop.
[ Always check the front of the
vehicle and road conditions before
departure.
Information
[Images or colors may appear
differently depending on the instrument
panel specifications or theme.

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 61-70 71-80 next >