HYUNDAI SANTA CRUZ 2022 Owners Manual

05
5-115
Fully closing tonneau cover
ONX4OB051020ONX4OB051020
1. Use strap to pull tonneau cover until
handle can be reached.
ONX4OB051071ONX4OB051071
2. Return handle to “latched” position.
3. Pull tonneau cover rearward until it
latches against the tailgate.
Half opening tonneau cover (from
open)
ONX4OB051065ONX4OB051065
1. Pull strap 45 degrees to the left to
return handle to “latched” position.
ONX4OB051068ONX4OB051068
2. Use strap to close tonneau past half
open position, then release. latch pins
will make audible click.

Convenient Features
5-116
Half opening tonneau cover (from
closed)
ONX4OB051062ONX4OB051062
1. Push tonneau handle forward until
unlatched. (Handle will stay in
“unlatched” position)
ONX4OB051067ONX4OB051067
2. Return handle to “latched” position.
3. Tonneau cover will open and stop at
halfway position.
NOTICE
• Tonneau cover is made of aluminium
profiles which heats up and cools
down relatively quick according to
weather conditions. This can cause
condensation on the inside of the
profiles and the panels.
• The pull strap has been designed
only for opening and closing the Roll
cover. The carabineer and ring will be
damaged in case of excessive load.
• Goods in the pickup bed must be
secured during transportation to
prevent damage on the structural
parts of tonneau cover (especially
the canister.)
• If the tonneau cover is closed and
has water, snow, ice or dirt on the
cover, it might enter into the pickup
bed as the cover retracts. To avoid
this, clean off the top surface of the
cover prior to opening.
• When opening the cover, the
opening should be careful and
controlled using the pull strap to
prevent the cover from hitting the
front with full speed, which it has
NOT been designed for.
CAUTION
• The Roll cover is not designed for
loading although it can support
normal snow loads. No part of it
can support any load from cargo or
persons and the product might be
damaged if somebody stands on it.

05
5-117
WARNING
• Do not drive with persons under the
tonneau cover.
• Do not allow persons or animals
to stay in the pickup bed when the
cover is closed.
• Temperatures can be very high under
the cover when closed.
• The pull strap should not be used to
tie down cargo.
• Do not disassemble the main shaft
from the canister without relieving
the spring tension completely.
• Remove fingers from lamellas when
opening and closing.
• We do not recommend washing
the tonneau cover in a brushless
carwash, as the coating may be
damaged due to use of chemicals.
• Wash the Roll cover regularly using
normal car shampoo and a soft, lint
free cloth or brush.
• If washed in any carwash, or if any
chemicals are used on the roll cover,
please ensure a max PH value of 8 is
used.
•
Sidewall Molded in Features
Commonly sold lumber items to be
added to the pickup bed, allowing users
to customize.
2x6 cross pickup bed support shelf
ONX4OB051073ONX4OB051073
Cut two 2”x6” pieces of standard lumber
to ~52” lengths and inset into forming’s
provided on the sidewalls.
ONX4OB051074ONX4OB051074
A 4’x4’ sheet of plywood can be placed
on top of the 2x6 supports to form a shelf
within the pickup bed.

Convenient Features
5-118
Plywood carrying shelf
ONX4OB051075ONX4OB051075
Steps to put tailgate in plywood position:
1. Detach both left and right support
cables.
2. Lift tailgate upward to 20 degrees
from full open position.
3. Connect both cables just below.
WARNING
• Close the tonneau cover securely
before driving.
• Cargo should not be interfered
with tonneau cover latching and
completely closing.
• When the tonneau cover is fully
opened, make sure that the buckle
is secure by pulling on the storage
strap.
• Be careful not to get your hands
pinched between the tonneau
cover and the deck when opening
and closing the tonneau cover, or
between the panels when folding.
• Make sure that all latches are
securely locked by pulling it
upwards.
• Do not stand or sit on the tonneau
cover.
• Do not install the tonneau
cover backwards, or in any other
orientation than indicated.
WARNING
• Allowing passengers to ride in the
pickup bed or on the tailgate can
result in death or serious injury in
a crash. Make sure all passengers
ride in a seat and wear a seat belt
properly.
• Never let passengers ride in the
pickup bed, in the trunk space, or on
the bed rails. This could cause very
serious injuries or death. No one
should ride in any position on your
vehicle that is not equipped with
seats and seat belts.
• Exceeding load limits or improperly
loading cargo on the vehicle can
cause a crash in which you can be
seriously injured or killed.
• Load the cargo securely before
starting to drive.

05
5-119
Underbed Storage
The underbed storage area is water
resistant and can be locked and unlocked
using the remote key or smart key.
Opening underbed storage
ONX4OB051021ONX4OB051021
The underbed storage can be unlocked
and opened by the following methods:
Vehicles equipped with remote key:
• Unlocking all doors using the main
unlock button in the vehicle or by
pressing the unlock button on the
remote key.
Vehicles equipped with Smart key:
• Unlocking all the doors using the
main unlock button in the vehicle or
by pressing the unlock button on the
smart key.
• Having the smart key in your
possession, opening the tailgate, and
then simply pressing the underfloor
storage release button.
Closing underbed storage
ONX4OB051022ONX4OB051022
To close the underbed storage lid, pull
the lid downward.
Note that if the underbed storage lid is
not fully closed, the LED bed lamps will
remain on and a warning message may
appear in the LCD cluster display.
Information
It is common for the underfloor storage
bin to have a scent when the vehicle is
new. This scent is normal, safe, and will be
reduced over time, similar to any new car
smell.
CAUTION
• Underbed storage should be dried
before closing the lid to prevent
mold growth.
• Take care to keep water channel and
sealing surface clear of debris.
• Do not store the valuable items
underbed storage area.
• Do not apply water directly to the
underbed storage bin latch. It may
cause latch damage.

Convenient Features
5-120
WARNING
ONX4OB051023ONX4OB051023
• Do not go into the underbed storage.
• If someone is locked inside the bin,
push the emergency release lever (1).
How to open underbed storage lid
manually
If there is an electrical failure that
prevents the bed underbed storage
lid from opening, the latch can be
mechanically released using the
following steps:
ONX4OB051076ONX4OB051076
1. Remove the tailgate assembly from its
hinges.
ONX4OB051077ONX4OB051077
2. Insert a ridged hook or tool between
the lid and floor, locating the release
cable with the tool.
3. Provide an even downward force to
release the latch.

05
5-121
Sidewall Side Storage
Opening/Closing sidewall side
storage
ONX4OB051024ONX4OB051024
Turn the two knobs to open/close the lid
Power Outlet (if quipped)
ONX4OB051025ONX4OB051025
Power outlet is located in the passenger
side sidewall side storage bin.
To use the power outlet
1. Turn the two knobs to the left to open
the lid.
2. Open the cover and plug in the
appliance slightly.
CAUTION
• Do not use the power outlet for
electrical appliances that require
high initial peak wattage, such as
cathode-ray tube type televisions,
refrigerators, electric pumps,
etc. It is not suitable for devices
that process precise data, such as
medical equipment, and that require
an extremely stable power supply,
such as microcomputer-controlled
electric blankets, touch sensor
lamps, etc.
• When the power outlet is not in use,
close the cover to prevent any small
foreign objects from getting into the
power outlet.
WARNING
• Continued use of any electrical
appliance/device exceeding these
ratings may result in damage to the
appliance/device.
• Make sure that no moisture is
trapped in a bin when closed to
prevent mold growth.

Convenient Features
5-122
Tie Down
Tie Down Locations
ONX4OB051026ONX4OB051026
[A] Fixed Tie Down
[B] D-Ring
You can secure cargo to the vehicle using
hooks, ropes and straps with heavy duty
tie downs from various location on the
pickup bed.
• Fixed Tie Down also acts as a Cleat for
looping rope.
• D-Ring can be rotated about the bolt
and the bracket.
• D-Ring and Fixed Tie Down can be
hooked through their openings.
Information
• Put cargo evenly on the pickup bed.
Place the heaviest items on the bottom
and as far forward as possible of the
rear axle. Tie down and secure all items
that could be thrown out of the vehicle
during a crash or sudden stop.
• If you stack items higher than the bed
sides, tailgate, or back window, secure
them with a net or cover. This will
reduce the risk of items being thrown
out of the pickup bed during a crash or
sudden stop.
CAUTION
• Load the cargo securely before
starting to drive.
WARNING
• Do not exceed 440 lbs. (200 kgf) load
on a tie down.
WARNING
• Allowing passengers to ride in the
pickup bed or on the tailgate can
result in death or serious injury in
a crash. Make sure all passengers
ride in a seat and wear a seat belt
properly
• Never let passengers ride in the
pickup bed, in the trunk space, or on
the bed rails. This could cause very
serious injuries or death. No one
should ride in any position on your
vehicle that is not equipped with
seats and seat belts.
• Exceeding load limits or improperly
loading cargo on the vehicle can
cause a crash in which could result in
serious injury or death.
• Load the cargo carefully before
starting to drive.

05
5-123
Rail and cleat system (If
equipped)
Rail and cleat Locations
ONX4OB051082ONX4OB051082
You can secure cargo with adjustable
heavy duty cleat tie downs,
repositioning the tie downs to suit the
exact needs. Cleat can be used with
ropes, hooks, and straps. It can be
hooked through the center or wrapped
around the cleats.
To use the cleat
1. Pull and Twist on Cleat Knob until
Knob is fully disengaged and locked.
2. Slide the Cleat to desired position.
3. Unlock the Knob by twisting the knob
in the opposite direction.
4. Slide the Cleat until the plunger is
locked into a detent.
WARNING
• Do not exceed 250 Ibs. (113 kgf) load
on a tie down.
• Do not load the cleat above or below
45 degrees from the horizontal.
• Do not apply a load to an unlocked
cleat.

Convenient Features
5-124
INTERIOR FEATURES
Cup Holder
„„FrontFront
ONX4OB051027ONX4OB051027
Cups or small beverages cups may be
placed in the cup holders.
WARNING
• Avoid abrupt starting and braking
when the cup holder is in use to
prevent spilling your drink. If hot
liquid spills, you could be burned.
Such a burn to the driver could cause
loss of vehicle control resulting in an
accident.
• Do not place uncovered or unsecured
cups, bottles, cans, etc., in the cup
holder containing hot liquid while
the vehicle is in motion. Injuries may
result in the event of a sudden stop
or collision.
• Only use soft cups in the cup holders.
Hard objects can injure you in an
accident.
WARNING
Keep cans or bottles out of direct sun
light and do not put them in a hot
vehicle. It may explode.
NOTICE
• Keep your drinks sealed while
driving to prevent spilling your drink.
If liquid spills, it may get into the
vehicle’s electrical/electronic system
and damage electrical/electronic
parts.
• When cleaning spilled liquids, do not
use hot air to blow out or dry the cup
holder. This may damage the interior.