sensor INFINITI FX35 2004 Owner's Manual

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-49
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
DTC 65 PRESSURE CONTROLAKS006Z8
1. OPERATION CHECK

Check foot brake pedal operates normally.
OK or NG
OK >> GO TO 2.
NG >>

Check brake circuit.

After repair, Erase DTC, and perform active test (BOOSTER SOL/V3) with CONSULT-II. Then
perform self-diagnosis of ICC system again.
2. CHECK BOOSTER SOLENOID

Check booster solenoid. Refer to ACS-65, "Booster Solenoid" .
OK or NG
OK >> GO TO 3.
NG >>

Solenoid malfunction.

Replace booster. Erase DTC and perform ICC system running test. Then perform self-diagno-
sis of ICC system again.
3. CHECK HARNESS BETWEEN SOLENOID/RELEASE SWITCH AND ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector and brake booster solenoid/
release switch connector.
3. Check continuity between ICC unit harness connector M88 ter-
minal 10 (B/R), 12 (L/W) and brake booster solenoid/release
harness connector E54 terminal 4 (B), 6 (L).
OK or NG
OK >> Replace ICC unit. Erase DTC and perform ICC system
running test. Then perform self-diagnosis of ICC system
again.
NG >>

Repair harness between brake booster solenoid/release switch and ICC unit.

After repair, Erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 74 LASER BEAM OFF CNTRAKS006Z9
1. DIAGNOSTIC CHECK
1. Adjust laser beam aiming. Then erase DTC, and perform ICC system ICC system running test.
2. After that, perform self-diagnosis of ICC system. Is DTC 74 LASER BEAM OFF CNTR indicated?
YES or NO
YES >>
Replace ICC sensor, and adjust laser beam aiming.

After that, Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
NO >> INSPECTION END10 - 4, 12 - 6 Continuity should exist.
SKIA6654E

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-57
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II

With TCM data monitor with CONSULT-II, check that gear positions are correct.
OK or NG
OK >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE ROTATION
With CONSULT-II

With TCM diagnosis, check that turbine rpm is normal. Refer to AT- 1 4 3 , "DTC P1716 TURBINE REVOLU-
TION SENSOR" .
OK or NG
OK >> Replace ICC unit. Erase DTC and perform self-diagnosis of ICC system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
DTC 102 RADAR STAINAKS006ZI
1. VISUAL INSPECTION (1)

Check that there is no contamination and foreign material on ICC sensor body window.
OK or NG
OK >> GO TO 2.
NG >>

If any, remove them.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
2. VISUAL INSPECTION (2)

Check ICC sensor body window for cracks.
OK or NG
OK >> GO TO 3.
NG >>

Replace ICC sensor, and adjust laser beam.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
3. ASKING COMPLAINTS
1. Is there any trace of contamination or foreign material on ICC sensor?
2. Is there any possibility that vehicle was driven in snow or ICC sensor was frosted?
3. Is there any possibility that ICC sensor was fogged temporarily? (Front window glass may have also
tended to be fogged.)
Ye s o r N o
Yes >> Explain difference in displays between contamination detection result and current indication to
customer, and tell them “This is not malfunction”.
No >>

Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.

ACS-58
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2004 November 2004 FX35/FX45
DTC 103 LASER SENSOR FAILAKS006ZJ
1. DIAGNOSTIC CHECK

Are “DTC 11 CONTROL UNIT” or “DTC 20 CAN COMM CIRCUIT” item indicated in self-diagnosis display
item?
YES or NO
YES >> GO TO APPLICABLE ITEM INSPECTION. Refer to ACS-41, "DTC 11 CONTROL UNIT" , and
ACS-41, "
DTC 20 CAN COMM CIRCUIT" .
NO >>

Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
DTC 104 LASER AIMING INCMPAKS006ZK
1. DIAGNOSTIC CHECK
1. Adjust laser beam aiming. Erase DTC and perform ICC system running test.
2. After that, perform self-diagnosis of ICC system. Is “DTC 104 LASER AIMING INCMP” indicated?
YES or NO
YES >>
Replace ICC sensor, and adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
NO >> INSPECTION END
DTC 107 LASER COMM FAILAKS006ZL
1. DIAGNOSTIC CHECK

Is “DTC 11 CONTROL UNIT” or “DTC 20 CAN COMM CIRCUIT” items other than “DTC 107 LASER
COMM FAIL” indicated in the self-diagnosis display item?
YES or NO
YES >> GO TO APPLICABLE ITEM INSPECTION. Refer to ACS-41, "DTC 11 CONTROL UNIT" , and
ACS-41, "
DTC 20 CAN COMM CIRCUIT" .
NO >>

Replace ICC sensor. Adjust laser beam aiming.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
DTC 109 LASER HIGH TEMPAKS006ZM
1. CHECK SYMPTOM

Is cooling system malfunctioning?
YES or NO
YES >>
Repair cooling system.

After that, erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC
system again.
NO >>

Replace ICC sensor, and adjust laser beam aiming.

After repair, erase DTC. Then perform ICC system running test, and perform self-diagnosis of
ICC unit.

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-63
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
2. CAN COMMUNICATION INSPECTION
With CONSULT-II
1. With CONSULT-II self-diagnosis, check that “CAN COMM CIRCUIT” item exists.
OK or NG
OK >> Refer to ACS-41, "DTC 20 CAN COMM CIRCUIT" .
NG >> After replacing combination meter, erase DTC. Perform ICC system running test, and then per-
form self-diagnosis of ICC system again.
Symptom 6: Driving Force Is Hunting.AKS006ZU
1. CHECK ECM
1. Perform self-diagnosis of ECM.
OK or NG
OK >> Refer toACS-63, "Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone Is Short." .
NG >> After repairing applicable parts, erase DTC. Perform ICC system running test, and then perform
self-diagnosis of ICC system again.
Symptom 7: The ICC System Frequently Cannot Detect the Vehicle Ahead/The
Detection Zone Is Short.
AKS006ZV
The detection function may become unstable in the following cases:

When the reflector of the vehicle ahead is deficient/ not clean enough to reflect the radar.

When driving a road with extremely sharp corners.

When the radar cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or
passing the peak.
1. VISUAL CHECK
1. Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Then perform ICC system run-
ning test.
NG >> GO TO 2.
2. CHECK FUNCTION
1. After adjusting ICC sensor beam aiming, perform ICC system running test. Check that preceding vehicle
detection performance has been improved.
OK or NG
OK >> INSPECTION END
NG >>

Replace ICC sensor, and perform laser beam aiming adjustment.

After performing above. Perform ICC system running test, and then perform self-diagnosis of
ICC system again.
Symptom 8: The System Does Not Detect the Vehicle Ahead at All.AKS006ZW
1. VISUAL CHECK
1. With ignition switch turned ON (engine not started), check that all indicator lamps in ICC system display
are continuously lit. (Check for a missing segment in preceding vehicle detection display.)
OK or NG
OK >> GO TO 2.
NG >> Check for combination meter. Refer to DI-13, "
How to Proceed With Trouble Diagnosis" in DI.

ACS-64
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November 2004 FX35/FX45
2. VISUAL CHECK

Check ICC sensor body window for contamination and foreign materials.
OK or NG
OK >> If any contamination or foreign materials are found, remove them. Perform ICC system running
test.
NG >> GO TO 3.
3. VISUAL CHECK

Check ICC sensor body window for cracks and scratches.
OK or NG
OK >> GO TO 4.
NG >>

Replace ICC sensor, and perform laser beam aiming adjustment.

After performing above. Perform ICC system running test, and then perform self-diagnosis of
ICC system again.
4. ADJUST ICC SENSOR
1. After adjusting ICC sensor beam aiming, perform ICC system running test. Check that preceding vehicle
detection performance has been improved.
OK or NG
OK >> INSPECTION END
NG >>

Replace ICC sensor, and perform laser beam aiming adjustment.

After performing above. Perform ICC system running test, and then perform self-diagnosis of
ICC system again.

REMOVAL AND INSTALLATION
ACS-67
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
REMOVAL AND INSTALLATIONPFP:00000
ICC UnitAKS00704
ICC SensorAKS00705
CAUTION:
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
ICC Steering SwitchAKS00707
Replace ICC steering switch as steering wheel assembly. Refer to PS-11, "Removal and Installation" .
SKIA5985E
SKIA5986E

AT-2Revision: 2004 November 2004 FX35/FX45Wiring Diagram — AT — PNP/SW .......................113
Diagnostic Procedure ...........................................114
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................116
Description ............................................................116
CONSULT-II Reference Value ..............................116
On Board Diagnosis Logic ....................................116
Possible Cause .....................................................116
DTC Confirmation Procedure ...............................116
Wiring Diagram — AT — VSSA/T .........................118
Diagnostic Procedure ...........................................119
DTC P0725 ENGINE SPEED SIGNAL ...................121
Description ............................................................121
CONSULT-II Reference Value ..............................121
On Board Diagnosis Logic ....................................121
Possible Cause .....................................................121
DTC Confirmation Procedure ...............................121
Diagnostic Procedure ...........................................121
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................123
Description ............................................................123
CONSULT-II Reference Value ..............................123
On Board Diagnosis Logic ....................................123
Possible Cause .....................................................123
DTC Confirmation Procedure ...............................123
Diagnostic Procedure ...........................................124
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .125
Description ............................................................125
CONSULT-II Reference Value ..............................125
On Board Diagnosis Logic ....................................125
Possible Cause .....................................................125
DTC Confirmation Procedure ...............................125
Diagnostic Procedure ...........................................126
DTC P0745 LINE PRESSURE SOLENOID VALVE .127
Description ............................................................127
CONSULT-II Reference Value ..............................127
On Board Diagnosis Logic ....................................127
Possible Cause .....................................................127
DTC Confirmation Procedure ...............................127
Diagnostic Procedure ...........................................128
DTC P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) ..................................................129
Description ............................................................129
On Board Diagnosis Logic ....................................129
Possible Cause .....................................................129
DTC Confirmation Procedure ...............................129
Wiring Diagram — AT — POWER ........................130
Diagnostic Procedure ...........................................131
DTC P1702 TRANSMISSION CONTROL MODULE
(RAM) ......................................................................133
Description ............................................................133
On Board Diagnosis Logic ....................................133
Possible Cause .....................................................133
DTC Confirmation Procedure ...............................133
Diagnostic Procedure ...........................................133
DTC P1703 TRANSMISSION CONTROL MODULE
(ROM) ......................................................................134
Description ............................................................134
On Board Diagnosis Logic ....................................134Possible Cause .....................................................134
DTC Confirmation Procedure ................................134
Diagnostic Procedure ............................................134
DTC P1704 TRANSMISSION CONTROL MODULE
(EEPROM) ...............................................................135
Description ............................................................135
On Board Diagnosis Logic ....................................135
Possible Cause .....................................................135
DTC Confirmation Procedure ................................135
Diagnostic Procedure ............................................135
DTC P1705 THROTTLE POSITION SENSOR ........136
Description ............................................................136
CONSULT-II Reference Value ...............................136
On Board Diagnosis Logic ....................................136
Possible Cause .....................................................136
DTC Confirmation Procedure ................................136
Diagnostic Procedure ............................................136
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................139
Description ............................................................139
CONSULT-II Reference Value ...............................139
On Board Diagnosis Logic ....................................139
Possible Cause .....................................................139
DTC Confirmation Procedure ................................139
Wiring Diagram — AT — FTS ...............................140
Diagnostic Procedure ............................................141
Component Inspection ..........................................142
DTC P1716 TURBINE REVOLUTION SENSOR ....143
Description ............................................................143
CONSULT-II Reference Value ...............................143
On Board Diagnosis Logic ....................................143
Possible Cause .....................................................143
DTC Confirmation Procedure ................................143
Diagnostic Procedure ............................................144
DTC P1721 VEHICLE SPEED SENSOR MTR .......145
Description ............................................................145
CONSULT-II Reference Value ...............................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ................................145
Diagnostic Procedure ............................................146
DTC P1730 A/T INTERLOCK .................................147
Description ............................................................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ................................147
Judgement of A/T Interlock ...................................147
Diagnostic Procedure ............................................148
DTC P1731 A/T 1ST ENGINE BRAKING ...............150
Description ............................................................150
CONSULT-II Reference Value ...............................150
On Board Diagnosis Logic ....................................150
Possible Cause .....................................................150
DTC Confirmation Procedure ................................150
Diagnostic Procedure ............................................151
DTC P1752 INPUT CLUTCH SOLENOID VALVE ..152
Description ............................................................152
CONSULT-II Reference Value ...............................152
On Board Diagnosis Logic ....................................152

AT-4Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value ..............................187
Diagnostic Procedure ...........................................187
TROUBLE DIAGNOSIS FOR SYMPTOMS ............188
Wiring Diagram — AT — NONDTC ......................188
A/T CHECK Indicator Lamp Does Not Come On . 191
Engine Cannot Be Started In “P” or “N” Position ..193
In “P” Position, Vehicle Moves When Pushed ......193
In “N” Position, Vehicle Moves ..............................194
Large Shock (“N” to “D” Position) .........................195
Vehicle Does Not Creep Backward In “R” Position .198
Vehicle Does Not Creep Forward In “D” Position . 201
Vehicle Cannot Be Started From D
1 .....................203
A/T Does Not Shift: D
1 → D2 ................................206
A/T Does Not Shift: D
2 → D3 ................................208
A/T Does Not Shift: D
3 → D4 ................................211
A/T Does Not Shift: D
4 → D5 ................................213
A/T Does Not Perform Lock-up ............................216
A/T Does Not Hold Lock-up Condition ..................218
Lock-up Is Not Released ......................................220
Engine Speed Does Not Return To Idle ................221
Cannot Be Changed to Manual Mode ..................222
A/T Does Not Shift: 5th gear → 4th gear ..............223
A/T Does Not Shift: 4th gear → 3rd gear ..............225
A/T Does Not Shift: 3rd gear → 2nd gear .............227
A/T Does Not Shift: 2nd gear → 1st gear .............229
Vehicle Does Not Decelerate By Engine Brake ....231
SHIFT CONTROL SYSTEM ....................................233
Control Device Removal and Installation ..............233
Adjustment of A/T Position ...................................234
Checking of A/T Position ......................................234
A/T SHIFT LOCK SYSTEM .....................................235
Description ............................................................235
Shift Lock System Electrical Parts Location .........235
Wiring Diagram — AT — SHIFT ...........................236
Diagnostic Procedure ...........................................237
KEY INTERLOCK CABLE ......................................239
Components .........................................................239
Removal and Installation ......................................240
ON-VEHICLE SERVICE ..........................................242
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 ...............................................................242
Parking Components (2WD Models Only) ............253Rear Oil Seal .........................................................259
Revolution Sensor Components (2WD Models
Only) .....................................................................260
AIR BREATHER HOSE ...........................................264
Removal and Installation .......................................264
TRANSMISSION ASSEMBLY .................................266
Removal and Installation (2WD Models) ...............266
Removal and Installation (AWD models) ..............269
OVERHAUL .............................................................274
Components ..........................................................274
Oil Channel ...........................................................282
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................284
DISASSEMBLY .......................................................286
Disassembly ..........................................................286
REPAIR FOR COMPONENT PARTS ......................303
Oil Pump ...............................................................303
Front Sun Gear, 3rd One-Way Clutch ...................306
Front Carrier, Input Clutch, Rear Internal Gear .....308
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................314
High and Low Reverse Clutch ..............................320
Direct Clutch .........................................................323
ASSEMBLY .............................................................325
Assembly (1) .........................................................325
Adjustment ............................................................338
Assembly (2) .........................................................341
SERVICE DATA AND SPECIFICATIONS (SDS) ....348
General Specifications ..........................................348
Vehicle Speed When Shifting Gears .....................348
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................349
Vehicle Speed When Performing and Releasing
Slip Lock-up ..........................................................349
Stall Speed ............................................................350
Line Pressure ........................................................350
A/T Fluid Temperature Sensor ..............................350
Turbine Revolution Sensor ....................................350
Vehicle Speed Sensor A/T (Revolution Sensor) ...350
Reverse Brake ......................................................350
Total End Play .......................................................351

PRECAUTIONS
AT-7
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ACS002L3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineACS002L5
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch “OFF” and disconnect the battery cable from the negative ter-
minal before any repair or inspection work. The open/short circuit of related switches, sensors,
solenoid valves, etc. will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. may cause the MIL to light up due to a short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.

AT-30
A/T CONTROL SYSTEM
Revision: 2004 November 2004 FX35/FX45
TCM FunctionACS002LF
The function of the TCM is to:

Receive input signals sent from various switches and sensors.

Determine required line pressure, shifting point, lock-up operation, and engine brake operation.

Send required output signals to the respective solenoids.
CONTROL SYSTEM OUTLINE
The automatic transmission senses vehicle operating conditions through various sensors or signals. It always
controls the optimum shift position and reduces shifting and lock-up shocks.
CONTROL SYSTEM DIAGRAM
SENSORS (or SIGNALS)

TCM

ACTUATORS
PNP switch
Accelerator pedal position sensor
Closed throttle position signal
Wide open throttle position signal
Engine speed signal
A/T fluid temperature sensor
Revolution sensor
Vehicle speed signal
Manual mode switch signal
Stop lamp switch signal
Turbine revolution sensor
ATF pressure switchShift control
Line pressure control
Lock-up control
Engine brake control
Timing control
Fail-safe control
Self-diagnosis
CONSULT-II communication line
Duet-EA control
CAN systemInput clutch solenoid valve
Direct clutch solenoid valve
Front brake solenoid valve
High and low reverse clutch
solenoid valve
Low coast brake solenoid valve
Torque converter clutch solenoid
valve
Line pressure solenoid valve
A/T CHECK indicator lamp
Starter relay
Back-up lamp relay
SCIA5325E