wiring diagram INFINITI FX35 2004 Owner's Guide

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-191
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
TCM terminals and data are reference value. Measured between each terminal and ground.
A/T CHECK Indicator Lamp Does Not Come OnACS007GD
SYMPTOM:
A/T CHECK indicator lamp does not come on for about 2 seconds when turning ignition switch to
“ON”.
DIAGNOSTIC PROCEDURE
1. CHECK CAN COMMUNICATION LINE
Perform self-diagnosis. Refer to AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 1 0 3 , "TCM SELF-DIAG-
NOSTIC PROCEDURE (NO TOOLS)" .
Is a malfunction in the CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT- 1 0 5 , "DTC U1000 CAN COMMUNICATION LINE" .
NO >> GO TO 2.
2. CHECK TCM POWER SOURCE
1. Disconnect A/T assembly harness connector.
2. Turn ignition switch ON. (Do not start engine.)
3. Check voltage between A/T assembly harness connector termi-
nals and ground. Refer to AT-130, "
Wiring Diagram — AT —
POWER" .
4. Turn ignition switch OFF.
5. Check voltage between A/T assembly harness connector termi-
nals and ground. Refer to AT-130, "
Wiring Diagram — AT —
POWER" .
OK or NG
OK >> GO TO 4.
NG >> GO TO 3.
TerminalWire
colorItem Condition Data (Approx.)
3 L CAN-H – –
4PUK-line (CONSULT-
II signal)The terminal is connected to the data link connector for CONSULT-II. –
7ORBack-up lamp
relaySelector lever in “R” position. 0V
Selector lever in other positions. Battery voltage
8 R CAN-L – –
Item ConnectorTerminal
(Wire color)Voltag e
TCM F441 (LG) - Ground
Battery voltage 2 (LG) - Ground
6 (Y) - Ground
SCIA2105E
Item ConnectorTerminal
(Wire color)Voltag e
TCM F441 (LG) - Ground
Battery voltage
2 (LG) - Ground
6 (Y) - Ground 0V
SCIA2104E

AT-192
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November 2004 FX35/FX45
3. DETECT MALFUNCTIONING ITEM
Check the following items:

Harness for short or open between battery and A/T assembly harness connector terminals 1, 2.

Harness for short or open between ignition switch and A/T assembly harness connector terminal 6

10A fuse (No.37, located in the fuse and fusible link box)

10A fuse (No.83, located in the IPDM E/R)

Ignition switch, Refer to PG-3, "POWER SUPPLY ROUTING CIRCUIT" .
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. CHECK TCM GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect A/T assembly harness connector.
3. Check continuity between A/T assembly harness connector terminals 5(B), 10(B) and ground. Refer to
AT- 1 3 0 , "
Wiring Diagram — AT — POWER" .
4. If OK, check the harness for short circuit to ground or the power
source.
OK or NG
OK >> GO TO 5.
NG >> Repair the open or short circuit in the harness or
connector.
5. CHECK A/T CHECK INDICATOR LAMP CIRCUIT
1. Turn ignition switch OFF.
2. Check the combination meter. Refer to DI-4, "
COMBINATION METERS" .
OK or NG
OK >> GO TO 6
NG >> Replace the combination meter. Refer to DI-26, "
Disassembly and Assembly for Combination
Meter" .
6. CHECK SELF-DIAGNOSTIC RESULTS
Perform self-diagnosis. Refer to AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" .
Do the self-diagnostic results indicate
“TCM-POWER SUPPLY”?
YES >> Check the TCM power circuit. Refer to AT- 1 2 9 , "DTC P1701 TRANSMISSION CONTROL MOD-
ULE (POWER SUPPLY)" .
NO >> GO TO 7.
7. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT- 2 4 2 , "Control Valve with TCM and A/T Fluid Tem-
perature Sensor 2" .
NG >> Repair or replace damaged parts.Continuity should exist.
SCIA2106E

AT-236
A/T SHIFT LOCK SYSTEM
Revision: 2004 November 2004 FX35/FX45
Wiring Diagram — AT — SHIFTACS002RV
TCWM0149E

A/T SHIFT LOCK SYSTEM
AT-237
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Diagnostic ProcedureACS002RW
SYMPTOM 1:

Selector lever cannot be moved from “P” position with key in ON position and brake pedal
applied.

Selector lever can be moved from “P” position with key in ON position and brake pedal released.

Selector lever can be moved from “P” position when key is removed from key cylinder.
SYMPTOM 2:

Ignition key cannot be removed when selector lever is set to “P” position.

Ignition key can be removed when selector lever is set to any position except “P” position.
1. CHECK KEY INTERLOCK CABLE
Check the key interlock cable for damage.
OK or NG
OK >> GO TO 2.
NG >> Repair key interlock cable. Refer to AT- 2 3 9 , "
KEY INTERLOCK CABLE" .
2. CHECK SELECTOR LEVER POSITION
Check the selector lever position for damage.
OK or NG
OK >> GO TO 3.
NG >> Adjustment control linkage. Refer to AT- 2 3 4 , "
Adjustment of A/T Position" .
3. CHECK SHIFT LOCK SOLENOID AND PARK POSITION SWITCH
1. Connect A/T device harness connector.
2. Turn ignition switch “ON”.
3. Selector lever is set in “P” position.
4. Check operation sound.
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4. CHECK POWER SOURCE
1. Turn ignition switch “ON”. (Do not start engine.)
2. Check the voltage between A/T device harness connector M67
terminal 1(G/R) and ground. Refer to AT- 2 3 6 , "
Wiring Diagram
— AT — SHIFT" .
OK or NG
OK >> GO TO 7.
NG >> GO TO 5.
Condition Brake pedal Operation sound
When ignition switch is turned to
“ON” position and selector lever
is set in “P” position.Depressed Yes
Released No
Condition Brake pedal Data (Approx.)
When ignition switch is turned to
“ON” position.Depressed Battery voltage
Released 0V
SCIA2122E

ATC-1
AUTOMATIC AIR CONDITIONER
J AIR CONDITIONER
CONTENTS
C
D
E
F
G
H
I
K
L
M
SECTION AT C
A
B
AT C
Revision: 2004 November 2004 FX35/FX45
AUTOMATIC AIR CONDITIONER
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Precautions for Working with HFC-134a (R-134a) ..... 5
CONTAMINATED REFRIGERANT ....................... 5
General Refrigerant Precautions .............................. 7
Lubricant Precautions .............................................. 7
Precautions for Refrigerant Connection ................... 8
ABOUT ONE-TOUCH JOINT ................................ 8
FEATURES OF NEW TYPE REFRIGERANT
CONNECTION .................................................... 10
O-RING AND REFRIGERANT CONNECTION .... 11
Precautions for Servicing Compressor ................... 13
Precautions for Service Equipment ........................ 13
RECOVERY/RECYCLING EQUIPMENT ............ 13
ELECTRONIC LEAK DETECTOR ...................... 13
VACUUM PUMP ................................................. 14
MANIFOLD GAUGE SET .................................... 14
SERVICE HOSES ............................................... 14
SERVICE COUPLERS ........................................ 15
REFRIGERANT WEIGHT SCALE ...................... 15
CHARGING CYLINDER ...................................... 15
Precautions for Leak Detection Dye ....................... 16
IDENTIFICATION ................................................ 16
IDENTIFICATION LABEL FOR VEHICLE ........... 16
Wiring Diagrams and Trouble Diagnosis ................ 16
PREPARATION ......................................................... 17
Special Service Tools ............................................. 17
HFC-134a (R-134a) Service Tools and Equipment ... 18
Commercial Service Tools ...................................... 20
REFRIGERATION SYSTEM ..................................... 21
Refrigerant Cycle ................................................... 21
REFRIGERANT FLOW ....................................... 21
FREEZE PROTECTION ..................................... 21
Refrigerant System Protection ............................... 21
REFRIGERANT PRESSURE SENSOR ............. 21
PRESSURE RELIEF VALVE ............................... 21
V-6 Variable Displacement Compressor ................. 22
GENERAL INFORMATION ................................. 22DESCRIPTION .................................................... 23
Component Layout ................................................. 26
LUBRICANT .............................................................. 27
Maintenance of Lubricant Quantity in Compressor ... 27
LUBRICANT ........................................................ 27
LUBRICANT RETURN OPERATION .................. 27
LUBRICANT ADJUSTING PROCEDURE FOR
COMPONENTS REPLACEMENT EXCEPT
COMPRESSOR .................................................. 28
LUBRICANT ADJUSTING PROCEDURE FOR
COMPRESSOR REPLACEMENT ....................... 29
AIR CONDITIONER CONTROL ............................... 30
Description of Air Conditioner LAN Control System ... 30
System Construction .............................................. 30
OPERATION ........................................................ 30
TRANSMISSION DATA AND TRANSMISSION
ORDER ............................................................... 31
AIR MIX DOOR CONTROL (AUTOMATIC TEM-
PERATURE CONTROL) ..................................... 32
FAN SPEED CONTROL ...................................... 32
INTAKE DOOR CONTROL ................................. 32
OUTLET DOOR CONTROL ................................ 32
MAGNET CLUTCH CONTROL ........................... 33
SELF-DIAGNOSTIC SYSTEM ............................ 33
Description of Control System ................................ 34
Control Operation ................................................... 34
DISPLAY SCREEN .............................................. 35
AUTO SWITCH ................................................... 35
TEMPERATURE SWITCH (POTENTIO TEM-
PERATURE CONTROL) (DRIVER SIDE) ........... 35
TEMPERATURE SWITCH (POTENTIO TEM-
PERATURE CONTROL) (PASSENGER SIDE) ... 35
RECIRCULATION (REC) SWITCH ..................... 35
FRESH (FRE) SWITCH ...................................... 35
DEFROSTER (DEF) SWITCH ............................. 35
REAR WINDOW DEFOGGER SWITCH ............. 35
OFF SWITCH ...................................................... 35
A/C SWITCH ....................................................... 35
MODE SWITCH .................................................. 35
FAN SWITCH ...................................................... 35

ATC-2Revision: 2004 November 2004 FX35/FX45DUAL SWITCH (WITH LEFT AND RIGHT VEN-
TILATION TEMPERATURE SEPARATELY
CONTROL SYSTEM) .......................................... 35
Fail-safe Function ................................................... 36
Discharge Air Flow ................................................. 37
System Description ................................................. 38
SWITCHES AND THEIR CONTROL FUNCTION ... 38
CAN Communication System Description .............. 39
TROUBLE DIAGNOSIS ............................................ 40
CONSULT-II ............................................................ 40
CONSULT-II BASIC OPERATION ....................... 40
DATA MONITOR .................................................. 41
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ...................................................... 42
WORK FLOW ...................................................... 42
SYMPTOM TABLE .............................................. 42
Component Parts and Harness Connector Location ... 43
ENGINE COMPARTMENT .................................. 43
PASSENGER COMPARTMENT .......................... 44
Schematic ............................................................... 45
Wiring Diagram —A/C— ......................................... 46
Auto Amp. Terminals and Reference Value ............ 51
PIN CONNECTOR TERMINAL LAYOUT ............ 51
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ........................ 51
Self-diagnosis Function .......................................... 53
DESCRIPTION .................................................... 53
FUNCTION CONFIRMATION PROCEDURE ...... 54
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................... 59
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................... 60
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION ................................................. 60
Operational Check .................................................. 61
CHECKING MEMORY FUNCTION ..................... 61
CHECKING BLOWER ......................................... 61
CHECKING DISCHARGE AIR ............................ 61
CHECKING RECIRCULATION ............................ 62
CHECKING TEMPERATURE DECREASE ......... 62
CHECKING TEMPERATURE INCREASE .......... 62
CHECK A/C SWITCH .......................................... 62
CHECKING AUTO MODE ................................... 63
Power Supply and Ground Circuit for Auto Amp. ... 63
INSPECTION FLOW ........................................... 63
COMPONENT DESCRIPTION ............................ 64
DIAGNOSTIC PROCEDURE FOR A/C SYSTEM ... 64
LAN System Circuit ................................................ 66
DIAGNOSTIC PROCEDURE FOR LAN CIR-
CUIT .................................................................... 66
Mode Door Motor Circuit ........................................ 70
INSPECTION FLOW ........................................... 70
SYSTEM DESCRIPTION .................................... 71
COMPONENT DESCRIPTION ............................ 72
DIAGNOSTIC PROCEDURE FOR MODE
DOOR MOTOR ................................................... 72
Air Mix Door Motor Circuit ...................................... 73
INSPECTION FLOW ........................................... 73SYSTEM DESCRIPTION ..................................... 74
COMPONENT DESCRIPTION ............................ 75
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR .................................................................. 75
Air Mix Door Motor PBR Circuit .............................. 75
DIAGNOSTIC PROCEDURE FOR AIR MIX
DOOR PBR .......................................................... 75
Intake Door Motor Circuit ........................................ 76
INSPECTION FLOW ............................................ 76
SYSTEM DESCRIPTION ..................................... 77
COMPONENT DESCRIPTION ............................ 78
DIAGNOSTIC PROCEDURE FOR INTAKE
DOOR MOTOR .................................................... 78
Blower Motor Circuit ................................................ 79
INSPECTION FLOW ............................................ 79
SYSTEM DESCRIPTION ..................................... 80
COMPONENT DESCRIPTION ............................ 81
DIAGNOSTIC PROCEDURE FOR BLOWER
MOTOR ................................................................ 81
COMPONENT INSPECTION ............................... 83
Magnet Clutch Circuit .............................................. 84
INSPECTION FLOW ............................................ 84
SYSTEM DESCRIPTION ..................................... 85
DIAGNOSTIC PROCEDURE FOR MAGNET
CLUTCH .............................................................. 85
COMPONENT INSPECTION ............................... 90
Insufficient Cooling .................................................. 91
INSPECTION FLOW ............................................ 91
PERFORMANCE TEST DIAGNOSIS .................. 93
PERFORMANCE CHART .................................... 95
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................... 96
DIAGNOSTIC PROCEDURE FOR INSUFFI-
CIENT COOLING ................................................. 98
Insufficient Heating ...............................................100
INSPECTION FLOW ..........................................100
Noise .....................................................................101
INSPECTION FLOW ..........................................101
Self-diagnosis .......................................................102
INSPECTION FLOW ..........................................102
Memory Function ..................................................103
INSPECTION FLOW ..........................................103
Ambient Sensor Circuit .........................................104
COMPONENT DESCRIPTION ..........................104
AMBIENT TEMPERATURE INPUT PROCESS .104
DIAGNOSTIC PROCEDURE FOR AMBIENT
SENSOR ............................................................104
COMPONENT INSPECTION .............................106
In-vehicle Sensor Circuit .......................................107
COMPONENT DESCRIPTION ..........................107
DIAGNOSTIC PROCEDURE FOR IN-VEHICLE
SENSOR ............................................................108
COMPONENT INSPECTION .............................109
Sunload Sensor Circuit .........................................110
COMPONENT DESCRIPTION ..........................110
SUNLOAD INPUT PROCESS ...........................110
DIAGNOSTIC PROCEDURE FOR SUNLOAD
SENSOR ............................................................110

ATC-16
PRECAUTIONS
Revision: 2004 November 2004 FX35/FX45
Precautions for Leak Detection DyeAJS00141

The A/C system contains a fluorescent leak detection dye used for locating refrigerant leaks. An ultraviolet
(UV) lamp is required to illuminate the dye when inspecting for leaks.

Always wear fluorescence enhancing UV safety goggles to protect your eyes and enhance the visibility of
the fluorescent dye.

The fluorescent dye leak detector is not a replacement for an electronic refrigerant leak detector. The fluo-
rescent dye leak detector should be used in conjunction with an electronic refrigerant leak detector to (J-
41995) pin-point refrigerant leaks.

For your safety and your customer′s satisfaction, read and follow all manufacture′s operating instructions
and precautions prior to performing the work.

A compressor shaft seal should not be repaired because of dye seepage. The compressor shaft seal
should only be repaired after confirming the leak with an electronic refrigerant leak detector (J-41995).

Always remove any remaining dye from the leak area after repairs are complete to avoid a misdiagnosis
during a future service.

Do not allow dye to come into contact with painted body panels or interior components. If dye is spilled,
clean immediately with the approved dye cleaner. Fluorescent dye left on a surface for an extended period
of time cannot be removed.

Do not spray the fluorescent dye cleaning agent on hot surfaces (engine exhaust manifold, etc.).

Do not use more than one refrigerant dye bottle (1/4 ounce /7.4 cc) per A/C system.

Leak detection dyes for HFC-134a (R-134a) and CFC-12 (R-12) A/C systems are different. Do not use
HFC-134a (R-134a) leak detection dye in CFC-12 (R-12) A/C system or CFC-12 (R-12) leak detector dye
in HFC-134a (R-134a) A/C system or A/C system damage may result.

The fluorescent properties of the dye will remain for over three (3) years unless a compressor malfunction
occurs.
IDENTIFICATION
NOTE:
Vehicles with factory installed fluorescent dye have a green label.
Vehicles without factory installed fluorescent dye have a blue label.
IDENTIFICATION LABEL FOR VEHICLE
Vehicles with factory installed fluorescent dye have this identification
label on the front side of hood.
Wiring Diagrams and Trouble DiagnosisAJS00142
When you read wiring diagrams, refer to the following:

GI-15, "How to Read Wiring Diagrams" in GI section.

PG-4, "Wiring Diagram - POWER -" in PG section.
When you perform trouble diagnosis, refer to the following:

GI-11, "How to Follow Trouble Diagnoses" in GI section.

GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section.
SHA436FA

ATC-46
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
Wiring Diagram —A/C—AJS0014N
TJWM0052E

AV-1
AUDIO VISUAL, NAVIGATION & TELEPHONE SYS-
TEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION AV
A
B
AV
Revision: 2004 November 2004 FX35/FX45
AUDIO VISUAL, NAVIGATION & TELEPHONE SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Wiring Diagrams and Trouble Diagnosis .................. 5
PREPARATION ........................................................... 6
Commercial Service Tools ........................................ 6
AUDIO ......................................................................... 7
System Description .................................................. 7
BASE SYSTEM ..................................................... 7
BOSE SYSTEM .................................................... 7
SPEED SENSITIVE VOLUME SYSTEM .............. 8
Component Parts and Harness Connector Location ..... 9
Schematic -Base System- ...................................... 10
WITH NAVIGATION SYSTEM ............................. 10
WITHOUT NAVIGATION SYSTEM ...................... 11
Wiring Diagram -AUDIO- / Base System ............... 12
Schematic -BOSE System- .................................... 19
WITH NAVIGATION SYSTEM ............................. 19
WITHOUT NAVIGATION SYSTEM ..................... 20
Wiring Diagram -AUDIO- / BOSE System .............. 21
Terminals and Reference Value for Audio Unit ....... 30
Terminals and Reference Value for BOSE Speaker
Amp. ....................................................................... 31
Terminals and Reference Value for A/C and AV
Switch ..................................................................... 33
Terminals and Reference Value for Woofer ............ 34
A/C and AV Switch Self-Diagnosis Function .......... 35
STARTING THE SELF-DIAGNOSIS MODE ....... 35
DIAGNOSIS FUNCTION ..................................... 35
EXITING THE SELF-DIAGNOSIS MODE ........... 35
Trouble Diagnosis .................................................. 35
MALFUNCTION WITH RADIO, TAPE AND CD
(BASE SYSTEM) ................................................ 35
MALFUNCTION WITH RADIO, TAPE AND CD
(BOSE SYSTEM) ................................................ 36
FOR RADIO ONLY .............................................. 37
FOR CASSETTE PLAYER ONLY ....................... 37
FOR CD ONLY .................................................... 37
Noise Inspection ..................................................... 38TYPE OF NOISE AND POSSIBLE CAUSE ........ 38
Power Supply Circuit Inspection ............................. 39
Audio Steering Wheel Switch Inspection ................ 40
A/C and AV Switch Inspection ................................ 41
BOSE Speaker Amp. Inspection ............................ 42
Vehicle Speed Signal Inspection ............................ 42
Locking CD Auto-changer Mechanism ................... 44
DAMPER LOCK PROCEDURE .......................... 44
Removal and Installation of Audio Unit ................... 44
REMOVAL ........................................................... 44
INSTALLATION ................................................... 44
Disassembly and Assembly for Audio Unit ............. 45
DISASSEMBLY ................................................... 45
ASSEMBLY ......................................................... 45
Removal and Installation for A/C and AV Switch .... 45
REMOVAL ........................................................... 45
INSTALLATION ................................................... 46
Removal and Installation for Front Door Speaker ... 46
REMOVAL ........................................................... 46
INSTALLATION ................................................... 46
Removal and Installation for Rear Door Speaker ... 46
REMOVAL ........................................................... 46
INSTALLATION ................................................... 46
Removal and Installation for Instrument Speaker ... 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 47
Removal and Installation for Tweeter ..................... 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 47
Removal and Installation for Woofer (BOSE Sys-
tem) ........................................................................ 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 47
Removal and Installation for BOSE Speaker Amp. ... 48
REMOVAL ........................................................... 48
INSTALLATION ................................................... 48
AUDIO ANTENNA .................................................... 49
System Description ................................................. 49
Wiring Diagram — M/ANT — ................................. 50
Terminals and Reference Value for Audio Unit ....... 51

AV-2Revision: 2004 November 2004 FX35/FX45Antenna Amp. Inspection ....................................... 51
Location of Antenna ................................................ 52
Window Antenna Repair ......................................... 52
CHECK ELEMENT .............................................. 52
Removal and Installation of Roof Antenna ............. 54
REMOVAL ........................................................... 54
INSTALLATION .................................................... 54
INTEGRATED DISPLAY SYSTEM ............................ 55
System Description ................................................. 55
A/C AND AV SWITCH SYSTEM .......................... 55
PRECAUTION OF LCD MONITOR ..................... 55
POWER SUPPLY AND GROUND ....................... 55
DRIVE COMPUTER ............................................ 56
E/M SWITCH ....................................................... 57
SETTING SCREEN ............................................. 58
WARNING INDICATIONS ................................... 59
AV COMMUNICATION LINE ............................... 59
CAN Communication System Description .............. 60
CAN Communication Unit ....................................... 61
Component Parts and Harness Connector Location ... 61
Schematic ............................................................... 62
Wiring Diagram — INF/D — ................................... 63
Schematic ............................................................... 68
Wiring Diagram — COMM — ................................. 69
Terminals and Reference Value for Display Unit .... 72
Terminals and Reference Value for A/C and AV
Switch ..................................................................... 73
On Board Self-Diagnosis Function ......................... 74
DESCRIPTION .................................................... 74
DIAGNOSIS ITEM ............................................... 74
Self-Diagnosis Mode .............................................. 74
OPERATION PROCEDURES ............................. 74
NETWORK CHECK ............................................. 75
PARTS CHECK ................................................... 76
HVAC DETAIL SCREEN ...................................... 76
VERSION CHECK ............................................... 76
CAN DIAG MNTR (CAN DIAG MONITOR) ......... 76
A/C and AV Switch Self-Diagnosis Function ........... 77
STARTING THE SELF-DIAGNOSIS MODE ........ 77
DIAGNOSIS FUNCTION ..................................... 77
EXITING THE SELF-DIAGNOSIS MODE ........... 77
Trouble Diagnosis Chart by Symptom .................... 78
Power Supply and Ground Circuit Check for Display
Unit ......................................................................... 79
Power Supply and Ground Circuit Check for A/C and
AV Switch ................................................................ 80
Vehicle Speed Signal Inspection ............................ 80
Illumination Signal Inspection ................................. 81
Ignition Signal Inspection ........................................ 82
Audio Communication Line Inspection ................... 82
A/C and AV Switch Does Not Operate .................... 84
CAN Communication Line Inspection ..................... 85
Audio Steering Wheel Switch Inspection ................ 85
Removal and Installation of Display ........................ 87
REMOVAL ........................................................... 87
INSTALLATION .................................................... 87
Removal and Installation of A/C and AV Switch ..... 87
NAVIGATION SYSTEM ............................................. 88
System Description ................................................. 88TRAVEL DISTANCE ............................................ 88
TRAVEL DIRECTION .......................................... 88
MAP-MATCHING ................................................. 88
GPS (GLOBAL POSITIONING SYSTEM) .......... 89
COMPONENT DESCRIPTION ............................ 90
BIRDVIEW™ ........................................................ 90
MAP DISPLAY ..................................................... 91
FUNCTION OF CENTER SWITCH ..................... 92
“VIEW” MODE ...................................................... 98
“HEADING” MODE .............................................. 99
“NEARBY DISPLAY ICONS” MODE .................... 99
“SAVE CURRENT LOCATION” MODE ................ 99
“ADJUST CURRENT LOCATION” MODE ........... 99
“AUTO RE-ROUTE” MODE ...............................100
“AVOID AREA SETTING” MODE ......................100
“CLEAR MEMORY” MODE ................................100
“EDIT ADDRESS BOOK” MODE .......................101
“GPS INFORMATION” MODE ...........................101
“QUICK STOP CUSTOMER SETTING” MODE .101
“SET AVERAGE SPEED” MODE ......................101
“TRACKING” MODE ..........................................102
GUIDANCE VOLUME ........................................102
DISPLAY WITH PUSHED “TRIP” BUTTON .......102
TRIP 1 OR TRIP 2 .............................................103
FUEL ECONOMY ..............................................103
MAINTENANCE .................................................103
ENGINE OIL OR TIRE ROTATION ....................103
TIRE PRESSURE ..............................................104
WARNING INDICATIONS ..................................104
CAN Communication System Description ............105
CAN Communication Unit .....................................105
Component Parts Location and Harness Connector
Location ................................................................105
Schematic—NAVI— ..............................................106
Wiring Diagram —NAVI— .....................................107
Schematic — COMM — ........................................115
Wiring Diagram — COMM — ................................116
Terminals and Reference Value for NAVI Control
Unit ........................................................................121
Terminals and Reference Value for Display Control
Unit ........................................................................123
Terminals and Reference Value for Display ..........127
Terminals and Reference Value for A/C and AV
Switch ...................................................................129
On Board Self-Diagnosis Function ........................130
DESCRIPTION ..................................................130
DIAGNOSIS ITEM .............................................130
Self-Diagnosis Mode (DCU) ..................................131
OPERATION PROCEDURE ..............................131
SELF–DIAGNOSIS RESULT .............................133
Self-Diagnosis Mode (NAVI) .................................133
OPERATION PROCEDURE ..............................133
SELF–DIAGNOSIS RESULT .............................135
Confirmation/Adjustment Mode .............................136
OPERATION PROCEDURE ..............................136
DISPLAY DIAGNOSIS .......................................136
VEHICLE SIGNALS ...........................................137
AUTO CLIMATE CONTROL ..............................137
NAVIGATION .....................................................138