air INFINITI FX35 2005 Service Manual

AUDIO AV-43
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect A/C and AV switch connector and spiral cable connector.
3. Check continuity between spiral cable harness connector terminals and A/C and AV switch harness con- nector terminals.
4. Check continuity between A/C and AV switch and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK SPIRAL CABLE
1. Disconnect spiral cable connector (Audio steering wheel switch harness side).
2. Check continuity between spiral cable connector terminal 24, 31, 32 and terminal 20, 17, 16.
OK or NG
OK >> GO TO 4.
NG >> Replace spiral cable.
Te r m i n a l s
Continuity
A/C and AV switch Spiral cable
Connector Terminal
(Wire color) Connector Terminal
(Wire color)
M64 12 (R/G)
M15 24 (R/G)
Ye s
13 (G/W) 32 (G/W)
14 (B/Y) 31 (B/Y)
Terminals Continuity
A/C and AV switch
—
Connector Terminal (Wire color)
M64 12 (R/G)
Ground No
13 (G/W)
14 (B/Y)
SKIA5955E
Terminals Continuity
Spiral cable
Connector Terminal Connector Terminal
M15 24
M203 20
Ye s
32 16
31 17
SKIA5874E

AV-44
AUDIO
Revision: 2005 July 2005 FX
4. CHECK AUDIO STEERING WHEEL SWITCH RESISTANCE
Check resistance audio steering wheel switch terminals.
OK or NG
OK >> INSPECTION END
NG >> Replace audio steering wheel switch.
A/C and AV Switch InspectionAKS007H9
1. A/C AND AV SWITCH SELF-DIAGNOSIS FUNCTION
1. Start A/C and AV switch self-diagnosis function. Refer to AV- 3 7 , "
A/C and AV Switch Self-Diagnosis Func-
tion" .
2. Operate A/C and AV switch.
Does the A/C and AV switch is operated normally?
YES >> INSPECTION END (System is OK)
NO >> Replace A/C and AV switch.
BOSE Speaker Amp. InspectionAKS007WD
1. CHECK HARNESS
1. Disconnect audio unit connector and BOSE speaker amp. con- nector.
2. Check continuity between audio unit harness connector M59 ter- minal 12 (G/W) and BOSE speaker amp. harness connector
B213 terminal 31 (P).
3. Check continuity between audio unit harness connector M59 ter- minal 12 (G/W) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
Terminal
(Wire color) Signal name Condition Resistance
( Ω )
16
(L)
17
(BR) Power Depress power switch. Approx. 0
Seek down Depress (station) down switch. Approx. 165
Volume (down) Depress volume down switch. Approx. 652
20
(W) Mode Depress mode switch. Approx. 0
Seek up Depress (station) up switch. Approx. 165
Volume (up) Depress volume up switch. Approx. 652
SKIA5010E
12 (GW) – 31 (P) : Continuity should exist.
12 (GW) – Ground : Continuity should not exist.
SKIA6816E

AUDIO AV-45
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
2. CHECK AMP. ON SIGNAL
1. Connect audio unit connector.
2. Turn the ignition switch ACC.
3. Check voltage between audio unit harness connector M59 ter- minal 12 (G/W) and ground.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace audio unit.
Vehicle Speed Signal InspectionAKS007VI
1. CHECK VEHICLE SPEED OPERATION
Start engine and drive vehicle.
Dose speedometer is operated normally?
Ye s > > G O T O 2 .
No >> Check combination meter trouble diagnosis. Refer to DI-15, "
Trouble Diagnosis" .
2. CHECK HARNESS
1. Turn the ignition switch OFF.
2. Disconnect audio unit connector and unified meter and A/C amp. connector.
3. Check continuity between audio unit harness connector M60 ter- minal 22 (W/L) and unified meter and A/C amp. harness connec-
tor M56 terminal 34 (W/L).
4. Check continuity between audio unit harness connector M60 ter- minal 22 (W/L) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector. 12 (G/W) – Ground : Approx. 12 V
SKIA6818E
22 (W/L) – 34(W/L) : Continuity should exist.
22 (W/L) – Ground : Continuity should not exist.
SKIA6807E

AV-46
AUDIO
Revision: 2005 July 2005 FX
3. CHECK VEHICLE SPEED SIGNAL
1. Connect unified meter and A/C amp. connector.
2. Start engine and drive vehicle at more than 40 km/h (25MPH).
3. Check the signal between audio unit harness connector M60 terminal 22 (W/L) and ground with CON- SULT-ll or oscilloscope.
OK or NG
OK >> INSPECTION END (System is OK.)
NG >> Replace unified meter and A/C amp.
Locking CD Auto-Changer MechanismAKS007GD
CAUTION:

Prior to removing a malfunctioning CD auto-changer unit that will be shipped for repair, the
changer mechanism MUST BE LOCKED to prevent the mechanism from being damaged during
shipping.

If a CD is jammed or unable to be removed from the unit, do NOT lock the changer mechanism. If
the unit is to be shipped for repair, carefully package the unit to prevent vibration and shock.
DAMPER LOCK PROCEDURE
1. Eject and remove any CDs from the audio unit.
2. Turn ignition switch OFF. Wait until audio unit display is off and mechanism stops moving (mechanism sound stops).
3. Press any one of the disc selection buttons once. When a display shows on the audio unit, press the same disc selection button again within 5 seconds.

The changer mechanism will lock itself within 10 seconds.
4. After mechanism stops moving (mechanism sound stops), open the driver and passenger window, and then disconnect negative battery cable.
NOTE:
After installing a new or remanufactured audio unit, switching the audio unit ON will automatically unlock the
mechanism. A special unlocking procedure is not required.
Terminal Condition Reference
signal
(+) (–)
22
(W/L) Ground When vehicle
speed is approx.40
km/h (25MPH)
SKIA6809EELF1080D

AV-54
AUDIO ANTENNA
Revision: 2005 July 2005 FX
Location of AntennaAKS005TX
Window Antenna RepairAKS005TY
CHECK ELEMENT
1. Attach probe circuit tester (ohm setting) to antenna terminal on
each side.
PKIB5079E
SEL250I

AV-74
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
On Board Self-Diagnosis FunctionAKS005U8
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.
DIAGNOSIS ITEM
Self-Diagnosis ModeAKS005U9
OPERATION PROCEDURES
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” switch, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)
4. Display unit connection check screen.
5. Select each connecting unit (CHANGER, SATELLITE RADIO).
13 (G/W) Ground Steering SW
B Input ON Press POWER
switch. Approx. 0 V
Audio steering
wheel switches
do not function.
Press SEEK
DOWN switch. Approx. 1.7 V
Press VOL DOWN
switch. Approx. 3.3 V
Except for above Approx. 5 V
14 (B/Y) — Steering SW
ground —— — — Audio steering
wheel switches
do not function.
Terminal No.
(Wire color) Item Signal
input/
output Condition
Voltage Example of
symptom
+– Ignition
switch Operation
Mode Item Description Reference page
Self-diagnosis NETWORK CHECK
Check network between control unit and switch connected
from display unit via communication line. AV-75, "
NETWORK CHECK"
PARTS CHECK
Perform diagnosis and setting of display unit.

Perform self-diagnosis for auto air conditioner system. AV- 7 5 , "PARTS CHECK"
VERSION CHECK Displays version of each unit.
AV- 7 6 , "VERSION CHECK"
CAN DIAG MNTR Display unit displays CAN communication status. AV- 7 6 , "CAN DIAG MNTR
(CAN DIAG MONITOR)"
PKIB4131E
SKIA5921E

INTEGRATED DISPLAY SYSTEM AV-75
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
6. Self-diagnosis screen is displayed.

Using the joystick, select each item, and perform diagnosis.
CAUTION:
If self-diagnosis cannot activated, refer to AV- 7 8 , "
Trouble
Diagnosis Chart by Symptom" .
NETWORK CHECK
Selecting NETWORK CHECK on self-diagnosis screen, display self-
diagnostic results.
PARTS CHECK

Selecting PARTS CHECK on self-diagnosis screen, display
selection screen.

Select DISPLAY, indicate DISPLAY DETAIL screen. Display
diagnosis and setting can be performed.

Select HVAC, Indicate HVAC DETAIL screen. Auto air condi-
tioner system self-diagnosis can be performed.
SKIA5922E
SKIA5923E
Diagnosis
item Contents DTC return condition Reference at error
HVAC OK/NG Communication error between unified meter and A/C amp. and display unit. AV- 8 5 , "
CAN Communication
Line Inspection"
SWITCH OK/NG Communication error between A/C and AV switch and display unit. AV- 8 4 , "AV Communication
Line Inspection"
AUDIO OK/NG Communication error between audio and display unit.AV- 8 2 , "Audio Communication
Line Inspection"
SKIA5924E

AV-76
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
Display Detail Screen
NOTE:
Except an audio screen.
HVAC DETAIL SCREEN
Press the joystick, start auto air conditioner system self-diagnosis.
Refer to AT C - 5 3 , "
Self-diagnosis Function" .
VERSION CHECK
Check ID and version of display, A/C and AV switch, audio, IVCS, changer, and Satellite Radio.
CAN DIAG MNTR (CAN DIAG MONITOR)
Display CAN communication status.
Items Description
FULL BLINK All display unit segments turn ON.
BLANK–ADJ Adjust the display time-out for 5 to 15 seconds. (Default is
10 seconds.)
NOTE
WARNING Select warning indication ON/OFF. (Default is ON.)
SKIA5925E
SKIA5926E
Items shown Contents
CANCOMM OK/NG CAN1 OK/UNKWN
CAN2 OK/UNKWN
CAN3 OK/UNKWN
CAN4 OK/UNKWN
CAN5 OK/UNKWN
CAN6 OK/UNKWN
CAN7 OK/UNKWN
CAN8 OK/UNKWN
CAN9 OK/UNKWN
SKIA5927E

AV-78
INTEGRATED DISPLAY SYSTEM
Revision: 2005 July 2005 FX
Trouble Diagnosis Chart by SymptomAKS005UB
Symptom Suspect Systems and reference
No screen is shown. Refer to
AV-79, "
Power Supply and Ground Circuit Check for Display Unit" .
If above is normal, replace display unit.
Screen does not switch to nighttime mode after the
lighting switch is turned 1st. Refer to
AV-81, "
Illumination Signal Inspection" .
TRIP and FUEL ECON screen do not appear. Refer to AV-82, "
Ignition Signal Inspection" .
Journey distance (DIST) is not added up. Refer to AV-80, "
Vehicle Speed Signal Inspection" .
Average vehicle speed (AVG) is not displayed.
Average fuel consumption (AVG) is not displayed.

Refer to AV-80, "Vehicle Speed Signal Inspection" .

Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
Distance to empty (DTE) is not displayed.

Check if speedometer operates. If it does not operate, go to AV- 8 0 , "Vehicle
Speed Signal Inspection" .

Check if fuel gauge operates. If it does not operate, go to DI-22, "Fuel Level
Sensor Signal Inspection" .

Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
Tire pressure is not displayed.

Check BCM (Body Control Module). Refer to BCS-3, "BCM (BODY CONTROL
MODULE)" .

Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
Door warning screen does not appear.

Refer to AV-80, "Vehicle Speed Signal Inspection" .

Refer to AV-85, "CAN Communication Line Inspection" .
If above is normal, replace display unit.
A/C and AV switch and all switch operation are not
possible.
(Do not start self-diagnosis.)

Refer to AV-80, "Power Supply and Ground Circuit Check for A/C and AV
Switch" .

Refer to AV-77, "A/C and AV Switch Self-Diagnosis Function" .

Refer to AV-84, "AV Communication Line Inspection" .
If above is normal, replace display unit.
Audio operation is not possible.

Refer to AV-77, "A/C and AV Switch Self-Diagnosis Function" .

Refer to AV-82, "Audio Communication Line Inspection" .
Audio steering wheel switches do not function. Refer to
AV-86, "
Audio Steering Wheel Switch Inspection" .
If above is normal, replace AV and A/C switch.
Air conditioner operation is not possible.

Refer to AV-77, "A/C and AV Switch Self-Diagnosis Function" .

Refer to AV-85, "CAN Communication Line Inspection" .

INTEGRATED DISPLAY SYSTEM AV-81
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display unit connector and unified meter and A/C amp. connector.
3. Check continuity between display unit harness connector M62 terminal 7 (R/G) and unified meter and A/C amp. harness con-
nector M56 terminal 26 (R/G).
4. Check continuity between display unit harness connector M62 terminal 7 (R/G) and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK VEHICLE SPEED SIGNAL
1. Connect unified meter and A/C amp. connector.
2. Drive vehicle at a constant speed.
3. Check the signal between display unit harness connector M62 terminal 7 (R/G) and ground with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace display unit.
NG >> Check unified meter and A/C amp. system. Refer to DI-20, "
Vehicle Speed Signal Inspection" .
Illumination Signal InspectionAKS005UF
1. CHECK ILLUMINATION SIGNAL
1. Turn ignition switch ON.
2. Check voltage between display unit and ground.
OK or NG
OK >> Replace display unit.
NG >> Check harness for open or short between display unit
and IPDM E/R.
Continuity should exist.
Continuity should not exist.
SKIA4989E
7 (R/G) - Ground:
PKIB6611E
PKIA1935E
Terminals Lighting switch position
(+)
(–)
Connector Terminal
(Wire color) 1st or 2nd position OFF
M62 4 (R/L) Ground Approx.12 V Approx. 0 V
SKIA4992E