INFINITI FX35 2005 Service Manual

LT-152
MAP LAMP
Revision: 2005 July 2005 FX
MAP LAMPPFP:26430
Bulb ReplacementAKS007ED
1. Remove lens using clip driver or suitable tool.
2. Remove bulb.
3. Installation is the reverse order of removal.
Removal and InstallationAKS007EE
REMOVAL
1. Insert a clip driver or suitable tool back of map lamp and pull down it to disengage pawl.
2. Pull down map lamp in direction shown by the arrow in the fig- ure.
3. Disconnect map lamp connector and remove map lamp.
INSTALLATION
Installation is the reverse order of removal. Map lamp : 12V - 8 W
PKIA2846E
PKIA2847E

PERSONAL LAMP LT-153
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
PERSONAL LAMPPFP:26415
Bulb ReplacementAKS007FT
1. Remove personal lamp. Refer to LT- 1 5 3 , "Removal and Installa-
tion" .
2. Remove screw from personal lamp.
3. Insert a screwdriver or similar tool and remove lens.
4. Remove bulb.
5. Installation is the reverse order of removal.
Removal and InstallationAKS007FU
REMOVAL
1. Use a clip driver or similar tool to press metal clip, and remove personal lamp.
2. Disconnect personal lamp connector.
INSTALLATION
Installation is the reverse order of removal. Personal lamp : 12V - 8W
SKIA5577E
SKIA5578E

LT-154
LUGGAGE ROOM LAMP
Revision: 2005 July 2005 FX
LUGGAGE ROOM LAMPPFP:26410
Bulb ReplacementAKS007FV
1. Remove luggage room lamp. Refer to LT- 1 5 4 , "Removal and
Installation" .
2. Remove screw from luggage room lamp.
3. Insert a suitable tool and remove lens.
4. Remove bulb.
5. Installation is the reverse order of removal.
Removal and InstallationAKS007FW
REMOVAL
1. Use a clip driver or similar tool to press metal clip, and remove luggage room lamp.
2. Disconnect luggage room lamp connector.
INSTALLATION
Installation is the reverse order of removal. Luggage room lamp : 12V - 8W
SKIA6197E
SKIA5579E

IGNITION KEY HOLE ILLUMINATION LT-155
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
IGNITION KEY HOLE ILLUMINATIONPFP:48476
Bulb Replacement, Removal and InstallationAKS007FR
1. Remove combination meter. Refer to DI-25, "Removal and
Installation of Combination Meter" in “DI” section.
2. Remove screw and remove NATS antenna amp.
3. Pull out ring and turn bulb socket to left to release lock.
4. Installation is the reverse order of removal. Ignition key hole illumination : 12V - 0.8W
SKIA5575E

LT-156
GLOVE BOX LAMP
Revision: 2005 July 2005 FX
GLOVE BOX LAMPPFP:68520
Bulb Replacement, Removal and InstallationAKS007FS
1. Remove instrument passenger lower panel. Refer to IP-18,
"INSTRUMENT PASSENGER LOWER PANEL" in “IP” section.
2. Turn bulb socket left to release lock and remove it.
3. Installation is the reverse order of removal. Glove box lamp : 12V - 1.4W
PKIB3636E

ASHTRAY ILLUMINATION LT-157
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
ASHTRAY ILLUMINATIONPFP:25860
Bulb Replacement and Removal and InstallationAKS007NZ
1. Remove A/T console finisher. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" in “IP” section.
2. Remove instrument ashtray and hazard switch. Refer to IP-16,
"A/T CONSOLE FINISHER" in “IP” section.
3. Use a screwdriver to undo ashtray finisher hooks.
4. Turn bulb socket on circuit board to left to undo lock. Remove bulb socket.
5. Installation is the reverse order of removal.
Ashtray and cigarette
lighter illumination : 12V - 1.4W
PKIA2850E

LT-158
CIGARETTE LIGHTER ILLUMINATION
Revision: 2005 July 2005 FX
CIGARETTE LIGHTER ILLUMINATIONPFP:25331
Bulb Replacement and Removal and InstallationAKS007O0
Refer to LT- 1 5 7 , "Bulb Replacement and Removal and Installation" in “ASHTRAY ILLUMINATION”.

INTERIOR ROOM LAMP LT-159
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
INTERIOR ROOM LAMPPFP:26410
Component Parts and Harness Connector LocationAKS007O8
System DescriptionAKS007F7
When the room lamp and personal lamp switch is in DOOR position, room lamp and personal lamp ON/OFF is
controlled by timer according to signals from switches including key switch, front door switch driver side,
unlock signal from keyfob, door lock and unlock switch, key cylinder lock and unlock switch, ignition switch.
PKIB3507E

LT-160
INTERIOR ROOM LAMP
Revision: 2005 July 2005 FX
When the room lamp and personal lamp turns ON, there is a gradual brightening over 1 second. When room
lamp and personal lamp turns OFF, there is a gradual dimming over 1 second.
The room lamp and personal lamp timer is controlled by the BCM (body control module).
Room lamp and personal lamp timer control settings can be changed with CONSULT-II.
Ignition keyhole illumination turns ON at time when driver door is opened (door switch ON) or removed keyfob
from key cylinder. Illumination turns OFF when driver door is closed (door switch OFF).
Step lamp turns ON at time when driver door or passenger door is opened (door switch ON). Lamp turns OFF
when the driver, passenger doors are closed (all door switches OFF).
POWER SUPPLY AND GROUND
Power is supplied at all times (without Intelligent Key system)

through 15A fuse [No. 22, located in fuse block (J/B)]

to key switch terminal 2, and

to BCM terminal 42,

through 50A fusible link (letter M, located in fuse, fusible link and relay box)

to BCM terminal 55,

through 10A fuse [No. 19, located in fuse block (J/B)]

to combination meter terminal 8.
Power is supplied at all times (with Intelligent Key system)

through 10A fuse (No.38, located in fuse, fusible link and relay box)

to key switch and ignition knob switch terminal 1,

through 15A fuse [No.22, located in fuse block (J/B)]

to BCM terminal 42,

to key switch and ignition knob switch terminal 3,

through 50A fusible link (letter M, located in fuse, fusible link and relay box)

to BCM terminal 55,

through 10A fuse [No. 19, located in fuse block (J/B)]

to combination meter terminal 8.
When key plate inserted to key switch, power is supplied (without Intelligent Key system)

through key switch terminal 1

to BCM terminal 37.
When inserted key plate to key switch, power is supplied (with Intelligent Key system)

through key switch and ignition knob switch terminal 4

to BCM terminal 37.
When moved ignition knob switch, power is supplied (with Intelligent Key system)

through ignition knob switch terminal 2

to intelligent key unit terminal 27.
With ignition switch in the ON or START position, power is supplied

through 15A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38.
Ground is supplied

to BCM terminals 49 and 52

through grounds terminals M35, M45 and M85.
When driver side door is opened, ground is supplied

through case ground of front door switch (driver side)

through front door switch (driver side) terminal 1

to BCM terminal 62.
When passenger side door is opened, ground is supplied

through case ground of front door switch (passenger side)

through front door switch (passenger side) terminal 1

to BCM terminal 12.

INTERIOR ROOM LAMP LT-161
C
D E
F
G H
I
J
L
M A
B
LT
Revision: 2005 July 2005 FX
When rear door LH is opened, ground is supplied

through case ground of rear door switch LH

through rear door switch LH terminal 1

to BCM terminal 63, and

to personal lamp LH terminal 1.
When rear door RH is opened, ground is supplied

through case ground of rear door switch RH

through rear door switch RH terminal 1

to BCM terminal 13, and

to personal lamp RH terminal 1.
When driver side door is unlocked by door lock and unlock switch, BCM receives a ground signal

through grounds terminals M35, M45 and M85

to power window main switch (door lock and unlock switch) terminal 17 or front power window switch
(passenger side) (door lock and unlock switch) terminal 11

from power window main switch (door lock and unlock switch) terminal 14 or front power window switch
(passenger side) (door lock and unlock switch) terminal 16

to BCM terminal 22.
When front driver side door is unlocked by driver side door lock assembly (key cylinder switch), BCM receives
a ground signal

through grounds M35, M45 and M85

to front door lock assembly (driver side) (key cylinder switch) terminal 5

from front door lock assembly (driver side) (key cylinder switch) terminal 6

to power window main switch (door lock and unlock switch) terminal 6

from power window main switch (door lock and unlock switch) terminal 14

to BCM terminal 22.
When a signal, or combination of signals is received by BCM, ground is supplied

to interior room lamp terminal 1 (without DVD player),

to map lamp terminal 2,

to front door inside handle illumination terminal 2, and

to rear door inside handle illumination terminal 2

through BCM terminal 48.
With power and supplied, interior lamp illuminates.
SWITCH OPERATION
When driver door switch is ON (door is opened), ground is supplied

through BCM terminal 1

to ignition keyhole illumination terminal 2.
And power is supplied

from BCM terminal 41

to ignition keyhole illumination terminal 1.
When any door switch is ON (door is opened), ground is supplied

through BCM terminal 47

to front step lamp (driver side and passenger side) and rear step lamp (LH and RH) terminals 2

through rear door switch (LH or RH) terminal 1

to personal lamp (LH or RH) terminals 1.
And power is supplied

from BCM terminal 41

to front step lamp (driver side and passenger side) and rear step lamp (LH and RH) terminals 1, and

to personal lamp (LH and RH) terminals 2
When map lamp switch is ON, ground is supplied