key INFINITI M35 2007 Factory Owner's Manual

BL-4Revision: 2007 April2007 M35/M45 Terminals and Reference Value for BCM ..............211
CONSULT-II Function (BCM) ................................212
CONSULT-II START PROCEDURE ..................212
DATA MONITOR ................................................212
ACTIVE TEST ...................................................212
Trouble Diagnosis .................................................213
TRUNK DOSE NOT OPEN WITH TRUNK LID
OPENER SWITCH / WITH INTELLIGENT KEY .213
VEHICLE SECURITY (THEFT WARNING) SYSTEM .217
Component Parts and Harness Connector Location .217
System Description ...............................................219
DESCRIPTION ..................................................219
POWER SUPPLY AND GROUND CIRCUIT .....220
INITIAL CONDITION TO ACTIVATE THE SYS-
TEM ...................................................................220
VEHICLE SECURITY SYSTEM ALARM OPER-
ATION ................................................................221
VEHICLE SECURITY SYSTEM DEACTIVATION .221
PANIC ALARM OPERATION .............................221
CAN Communication System Description ............221
CAN Communication Unit .....................................221
Schematic .............................................................222
Wiring Diagram — VEHSEC — ............................223
Terminals and Reference Value of BCM ...............229
Terminals and Reference Value of IPDM E/R .......229
CONSULT-II Function (BCM) ................................230
BASIC OPERATION ..........................................230
CONSULT-II APPLICATION ITEM .....................230
Trouble Diagnosis Work Flow ...............................231
Preliminary Check ................................................231
Trouble Diagnosis Symptom Chart .......................233
Diagnostic Procedure 1 ........................................234
DOOR SWITCH CHECK ...................................234
HOOD SWITCH CHECK ...................................237
TRUNK ROOM LAMP SWITCH CHECK ..........239
Diagnostic Procedure 2 ........................................241
SECURITY INDICATOR LAMP CHECK ............241
Diagnostic Procedure 3 ........................................242
FRONT DOOR KEY CYLINDER SWITCH
CHECK ..............................................................242
Diagnostic Procedure 4 ........................................242
VEHICLE SECURITY HORN ALARM CHECK . 242
Diagnostic Procedure 5 ........................................243
VEHICLE SECURITY HEADLAMP ALARM
CHECK ..............................................................243
Diagnostic Procedure 6 ........................................243
DOOR LOCK AND UNLOCK SWITCH CHECK .243
Diagnostic Procedure 7 ........................................243
VEHCLE SECURITY HAZARD LAMP ALARM
CHECK ..............................................................243
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ......................................................................244
Component Parts and Harness Connector Location .244
System Description ...............................................246
DESCRIPTION ..................................................246
PRECAUTIONS FOR KEY REGISTRATION ....246
SECURITY INDICATOR ....................................246
Operation Description ...........................................247
SYSTEM DIAGRAM ..........................................247OPERATION WHEN INSERTING TO KEY SLOT .247
OPERATION WHEN INTELLIGENT KEY IS
CARRIED ...........................................................247
PUSH-BUTTON IGNITION SWITCH OPERA-
TION PROCEDURE ..........................................247
ECM Re-Communicating Function .......................248
Schematic .............................................................250
Wiring Diagram — NATS — ..................................252
Terminals and Reference Value for Intelligent Key
Unit ........................................................................260
Terminals and Reference Value for Steering Lock
Unit ........................................................................262
Terminals and Reference Value for BCM ..............263
Terminals and Reference Value for IPDM E/R ......263
Terminals and Reference Value for PDU ..............264
CONSULT-II ..........................................................265
CONSULT-II INSPECTION PROCEDURE ........265
CONSULT-II DIAGNOSTIC TEST MODE FUNC-
TION ..................................................................266
HOW TO READ SELF-DIAGNOSTIC RESULTS .267
“NATS V5.0” SELF-DIAGNOSTIC RESULTS
ITEM CHART .....................................................268
“NATS BCM OR S/ENT” SELF-DIAGNOSTIC
RESULTS ITEM CHART ....................................268
“NATS I-KEY” SELF-DIAGNOSTIC RESULTS
ITEM CHART .....................................................269
Work Flow .............................................................269
Trouble Diagnoses Flow Chart for IVIS (NATS) ....272
Symptom Chart for Security Indicator ...................274
CONDITIONS OF VEHICLE (OPERATING CON-
DITIONS) ...........................................................274
Check Security Indicator Harness .........................274
DTC P1612 CHAIN of ECM-IMMU .......................275
DTC P1611 ID DISCORD, IMM-ECM ...................277
Removal and Installation of Key Slot ....................277
REMOVAL ..........................................................277
INSTALLATION ..................................................277
INTEGRATED HOMELINK TRANSMITTER ...........278
Wiring Diagram —TRNSCV— ..............................278
Trouble Diagnoses ................................................279
DIAGNOSTIC PROCEDURE .............................279
BODY REPAIR ........................................................281
Body Exterior Paint Color ......................................281
Body Component Parts .........................................282
UNDERBODY COMPONENT PARTS ...............282
BODY COMPONENT PARTS ............................284
Corrosion Protection .............................................286
DESCRIPTION ..................................................286
UNDERCOATING ..............................................287
Body Sealing .........................................................288
DESCRIPTION ..................................................288
Body Construction .................................................291
BODY CONSTRUCTION ...................................291
Body Alignment .....................................................292
BODY CENTER MARKS ...................................292
PANEL PARTS MATCHING MARKS .................293
DESCRIPTION ..................................................294
ENGINE COMPARTMENT ................................295
UNDERBODY ....................................................297

BL-6
PRECAUTIONS
Revision: 2007 April2007 M35/M45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NIS002B4
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Procedures without Cowl Top CoverNIS001WB
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
Precautions Necessary for Steering Wheel Rotation After Battery DisconnectNIS001WC
NOTE:

This Procedure is applied only to models with Intelligent Key system and NVIS/IVIS (NISSAN/INFINITI
VEHICLE IMMOBILIZER SYSTEM - NATS).

Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.

Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing
work. If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NVIS/IVIS, an electrically controlled steering lock
mechanism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
PIIB3706J

POWER DOOR LOCK SYSTEM
BL-25
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
System DescriptionNIS001WQ
Power is supplied at all times

through 50A fusible link (letter F , located in the fuse and fusible link box).

to BCM terminal 55,

through 10A fuse [No. 21, located in the fuse block (J/B)]

to BCM terminal 42.
When ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
When ignition switch is in ON or START position, power is supplied

through 15A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38.
Ground is supplied

to BCM terminal 52

through body grounds M16 and M70.
When the door is locked or unlocked with power window main switch (door lock and unlock switch), ground is
supplied

to CPU of power window main switch

through power window main switch (door lock and unlock switch) terminal 17

through grounds M16 and M70.
Then power window main switch (door lock and unlock switch) operation signal is sent.

to BCM terminal 22

from power window main switch (door lock and unlock switch) terminal 14
When the door is locked or unlocked with power window sub-switch (front passenger side) (door lock and
unlock switch), ground is supplied

to CPU of power window sub-switch

through power window sub-switch (front passenger side) (door lock and unlock switch) terminal 11

through grounds M16 and M70.
Then power window sub-switch (front passenger side) (door lock and unlock switch) operation signal is sent

to BCM terminal 22

from power window sub-switch (front passenger side) (door lock and unlock switch) terminal 16.
When the door is locked with front door key cylinder switch (driver side), ground is supplied

to CPU of power window main switch

through power window main switch (door lock and unlock switch) terminal 4

through front door key cylinder switch (driver side) terminals 6 and 4

through grounds M16 and M70.
Then front door key cylinder switch (driver side) operation signal (lock) is sent

to BCM terminal 22

from power window main switch (door lock and unlock switch) terminal 14
When the door is unlocked with front door key cylinder switch (driver side), ground is supplied

to CPU of power window main switch

through power window main switch (door lock and unlock switch) terminal 6

through front door key cylinder switch (driver side) terminals 5 and 4

through grounds M16 and M70.
Then front door key cylinder switch (driver side) operation signal (unlock) is sent

to BCM terminal 22

from power window main switch (door lock and unlock switch) terminal 14
BCM is connected to power window main switch and power window sub-switch as serial link.

BL-26
POWER DOOR LOCK SYSTEM
Revision: 2007 April2007 M35/M45
DOOR LOCK ACTUATOR OPERATION
When door is locked with door lock and unlock switch, all door lock actuator is locked. Ground is supplied

to BCM terminal 50

through each door lock actuator terminals 2 and 1

through BCM terminals 44 (driver side), 70 (passenger side) and 51 (rear door).
When door is unlocked with door lock and unlock switch, all door lock actuator is unlocked. Ground is supplied

to BCM terminals 44 (driver side), 70 (passenger side) and 51 (rear door)

through each door lock actuator terminals 1 and 2

through BCM terminal 50.
FUEL LID OPERATION
When door is locked with door lock and unlock switch, fuel lid lock actuator is locked. Ground is supplied

to BCM terminal 69

through fuel lid lock actuator terminals 2 and 1

through BCM terminal 44.
When door is unlocked with door lock and unlock switch, fuel lid lock actuator is unlocked. Ground is supplied

to BCM terminal 44

through fuel lid lock actuator terminals 1 and 2

through BCM terminal 69.
In this condition, fuel lid can be opened if it is pushed.
OUTLINE
Functions Available by Operating the Door Lock and Unlock Switches on Driver's Door and
Passenger's Door

Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors and
fuel lid lock actuator are locked.

Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors
and fuel lid lock actuator are unlocked.
Functions Available by Operating the Key Cylinder Switch on Driver's Door

Interlocked with the locking operation of door key cylinder, door lock actuators of all doors and fuel lid lock
actuator are locked.
Selective Unlock Operation

When door key cylinder is unlocked, door lock actuator driver side and fuel lid lock actuator are unlocked.

When door key cylinder is unlocked for the second time within 5 seconds after the first operation, door
lock actuators on all doors are unlocked.
Select unlock operation mode can be changed using “DOOR LOCK-UNLOCK SET” mode in “WORK SUP-
PORT”. Refer to BL-81, "
WORK SUPPORT" .
Key Reminder Door System
Refer to BL-49, "Key Reminder Function" .
CAN Communication System DescriptionNIS001WR
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitNIS001WS
Refer to LAN-50, "CAN System Specification Chart"

BL-32
POWER DOOR LOCK SYSTEM
Revision: 2007 April2007 M35/M45
CONSULT-II Function (BCM)NIS001WX
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II START PROCEDURE
Refer to GI-38, "CONSULT-II Start Procedure"
CONSULT-II APPLICATION ITEMS
Data Monitor
Active Test
BCM diagnosis
partInspection item, self-diagnosis
modeContent
Door lockDATA MONITOR Displays the input data of BCM in real time basis.
ACTIVE TEST Give a drive signals to load to check the operation check.
Monitor item Content
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
KEY ON SW Indicates [ON/OFF] condition of key switch.
CDL LOCK SW Indicates [ON/OFF] condition of lock signal from door lock and unlock switch.
CDL UNLOCK SW Indicates [ON/OFF] condition of unlock signal from door lock and unlock switch.
KEY CYL LK-SW Indicates [ON/OFF] condition of lock signal from key cylinder.
KEY CYL UN-SW Indicates [ON/OFF] condition of unlock signal from key cylinder.
DOOR SW-DR Indicates [ON/OFF] condition of front door switch driver side.
DOOR SW-AS Indicates [ON/OFF] condition of front door switch passenger side.
DOOR SW-RR Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL Indicates [ON/OFF] condition of rear door switch LH.
BACK DOOR SW This is displayed even if it is not equipped.
I -KEY LOCK Indicates [ON/OFF] condition of lock signal from Intelligent Key.
I - KEY UNLOCK Indicates [ON/OFF] condition of unlock signal from Intelligent Key.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position
I - KEY DR UNLK Indicates [ON/OFF] condition of unlock signal from door request switch (driver side)
I - KEY AS UNLK Indicates [ON/OFF] condition of unlock signal from door request switch (passenger side)
Test item in “DOOR LOCK” Content
ALL LOCKThis test is able to check all door lock actuators lock operation.
These actuators lock when “ALL LOCK” on CONSULT-II screen is touched.
DR UNLOCKThis test is able to check door lock actuator (driver side) unlock operation.
This actuator unlock when “DR UNLOCK” on CONSULT-II screen is touched.
OTHER UNLOCKThis test is able to check all door lock actuators (except driver side) unlock operation.
These actuators unlock when “OTHER UNLOCK” on CONSULT-II screen is touched.
ALL UNLOCKThis test is able to check all door lock actuators unlock operation.
These actuators unlock when “ALL UNLOCK” on CONSULT-II screen is touched.
AS UNLOCKThis test is able to check door lock actuator (passenger side) unlock operation.
This actuator unlock when “AS UNLOCK” on CONSULT-II screen is touched.

POWER DOOR LOCK SYSTEM
BL-33
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Trouble Diagnosis Chart by SymptomNIS001WY
Always check the “Work Flow” before troubleshooting. Refer to BL-31, "Work Flow" .
Symptom Diagnoses service procedureReference
page
Power door lock does not operate with door lock and unlock switch.1. Power supply and ground circuit check of
BCM.BL-34
2. Check door lock and unlock switch.BL-35
3. Check door lock actuator (driver side)BL-37
4. Replace BCM.BCS-15
Power door lock does not operate with door key cylinder operation.
(Power door lock operate properly with door lock and unlock
switch.)1. Check front door key cylinder switch.BL-41
2. Replace power window main switch. –
Specific door lock actuator does not operate.1. Check door lock actuator.Driver sideBL-37
Passenger sideBL-38
Rear LHBL-39
Rear RHBL-39
2. Replace BCM.BCS-15
Selective unlock operation does not operate.
(All other power door lock system is “OK”.)1. Check select unlock mode.
Select unlock mode can be changed.
First check select unlock mode.BL-81
2. Replace BCM.BCS-15
Fuel lid opener actuator does not operate.
(All door lock actuators operates properly.)Check fuel lid lock actuator.BL-40

POWER DOOR LOCK SYSTEM
BL-35
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Check Door Lock and Unlock Switch NIS001X0
1. CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
With CONSULT-II
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in DATA MONITOR mode with CONSULT-II.
Without CONSULT-II
1. Remove key from ignition switch, and the door of driver side and passenger side is closed.
2. Check signal between BCM connector and ground with oscilloscope when door lock and unlock switch
(driver side and passenger side) is turned “LOCK” or “UNLOCK”.
3. Make sure signals which are shown in the figure below can be detected during 10 second just after door
lock and unlock switch (driver side and passenger side) is turned “LOCK” or “UNLOCK”.
OK or NG
OK >> Door lock and unlock switch is OK.
NG >> GO TO 2.
Monitor item Condition
CDL LOCK SW LOCK : ON
UNLOCK : OFF
CDL UNLOCK SW LOCK : OFF
UNLOCK : ON
PIIA7068E
Terminal
Signal
(Reference value) (+)
(–)
BCM connector Terminal
M1 22 Ground
PIIB5957EPIIA1297E

POWER DOOR LOCK SYSTEM
BL-41
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
Door Key Cylinder Switch CheckNIS001X6
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
With CONSULT-II
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR ROCK SYS-
TEM” with CONSULT-II.
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between power window main switch connector and ground.
OK or NG
OK >> Key cylinder switch circuit is OK.
NG >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Disconnect power window main switch and front door key lock assembly (driver side) connector.
2. Check continuity between power window main switch connector and front door lock assembly (driver side)
connector.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
Monitor item Condition
KEY CYL LK-SWLock : ON
Neutral / Unlock : OFF
KEY CYL UN-SWUnlock : ON
Neutral / Lock : OFF
PIIA6285E
Terminals
Key positionVoltage (V)
(Approx.) (+)
(–) Power window
main switch
connectorTerminal
D104
GroundLock 0
Neutral / Unlock 5
6Unlock 0
Neutral / Lock 5
PIIB5956E
AB
Continuity Power window
main switch
connectorTerminalFront door lock
assembly
(driver side)
connectorTerminal
D104
D146
Ye s
65
PIIB5973E

BL-42
POWER DOOR LOCK SYSTEM
Revision: 2007 April2007 M35/M45
3. CHECK DOOR KEY CYLINDER SWITCH GROUND
Check continuity between front door lock assembly (driver side) connector ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK DOOR KEY CYLINDER SWITCH
Check front door lock assembly (driver side).
OK or NG
OK >> INSPECTION END.
NG >> Replace front door key cylinder (driver side) switch.
Front door lock
assembly
(driver side)
connectorTerminal Continuity
D14 4 Ground Yes
PIIB5974E
Terminal
Key position Continuity
Front door lock assembly
(driver side)
5
4Unlock Yes
Neutral / Lock No
6Lock Yes
Neutral / Unlock No
PIIB5975E

INTELLIGENT KEY SYSTEM
BL-43
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2007 April2007 M35/M45
INTELLIGENT KEY SYSTEMPFP:285e2
Component Parts and Harness Connector LocationNIS001X7
1. Fuse block (J/B) fuse layout 2. Fuse and fusible link box 3. BCM M1, M2, M3 (View with instru-
ment lower panel RH removed)
4. IPDM E/R E9 5. Push-button ignition switch M27
(Push switch)6. Combination meter M52
PIIB5860E