control unit INFINITI M35 2007 Factory Service Manual

GW-116
REVERSE INTERLOCK DOOR MIRROR SYSTEM
Revision: 2007 April2007 M35/M45
5. CHECK MIRROR SENSOR GROUND 1
1. Turn ignition switch OFF.
2. Disconnect door mirror connector.
3. Check continuity between door mirror connector and ground.
OK or NG
OK >> GO TO 8.
NG >> GO TO 6.
6. CHECK MIRROR SENSOR GROUND 2
Check continuity between automatic drive positioner control unit connector and ground.
OK or NG
OK >> GO TO 7.
NG >> Replace auto drive positioner control unit.
7. CHECK HARNESS CONTINUITY 2
1. Disconnect automatic drive positioner control unit connector.
2. Check continuity between automatic drive positioner control unit connector and door mirror connector.
3. Check continuity between automatic drive positioner control unit
connector and door mirror connector.
OK or NG
OK >> Check the condition of the harness and connector.
NG >> Repair or replace harness between automatic drive positioner control unit and door mirror.
Door mirror connector Terminal
GroundContinuity
D2 (LH)
D39 (RH)12 Yes
PIIB6034E
Automatic drive posi-
tioner control unit con-
nectorTerminal
GroundContinuity
M7 41 Yes
PIIB6029E
AB
Continuity Automatic
drive posi-
tioner control
unit connectorTerminalDoor mirror
connectorTerminal
M7 41D2 (LH)
D39 (RH)12 Yes
A
GroundContinuity Automatic drive
positioner control
unit connectorTerminal
M7 41 Yes
PIIB6035E

REVERSE INTERLOCK DOOR MIRROR SYSTEM
GW-117
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2007 April2007 M35/M45
8. CHECK HARNESS CONTINUITY 3
1. Disconnect automatic drive positioner control unit connector and door mirror connector.
2. [Door mirror LH]
–Check continuity between automatic drive positioner control unit connector and door mirror LH connector.
–Check continuity between automatic drive positioner control unit
connector and ground.
3. [Door mirror RH]
–Check continuity between automatic drive positioner control unit connector and door mirror RH connector.
–Check continuity between automatic drive positioner control unit
connector and ground.
OK or NG
OK >> Check the condition of harness and connector.
NG >> Repair or replace harness between automatic drive positioner control unit and door mirror con-
nector.
Check A/T Control Device R Position CircuitNIS0023F
1. CHECK R POSITION SIGNAL
Refer to AT- 1 8 6 , "
A/T INDICATOR CIRCUIT"
OK or NG
OK >> Refer to SE-37, "SELF-DIAGNOSIS RESULTS"
NG >> Refer to AT- 1 8 6 , "A/T INDICATOR CIRCUIT"
AB
Continuity Automatic
drive posi-
tioner control
unit connectorTerminalDoor mirror
LH connectorTerminal
M66
D29
Ye s
22 10
A
GroundContinuity Automatic drive
positioner control
unit connectorTerminal
M66
No
22
AB
Continuity Automatic
drive posi-
tioner control
unit connectorTerminalDoor mirror
RH connectorTerminal
M65
D399
Ye s
21 10
A
GroundContinuity Automatic drive
positioner control
unit connectorTerminal
M65
No
21
PIIB6036E
PIIB6030E

IDX-2
ALPHABETICAL INDEX
Symbols
(VK45DE) .............................................................. GI-6
(VQ35DE) ............................................................. GI-6
A
A/C air flow ...................................................... ATC-37
A/C component layout ..................................... ATC-25
A/C compressor mounting ........... ATC-153, ATC-157,
ATC-158
, ATC-159, ATC-161, ATC-163, ATC-164,
ATC-166
, ATC-167, ATC-168
A/C compressor precaution ............................. ATC-12
A/C compressor special service tool ................ ATC-16
A/C control operation (auto A/C) ...................... ATC-33
A/C diagnostic work flow (auto A/C) .............. ATC-110
A/C evaporator ............................................... ATC-167
A/C HFC134a (R134a) system precaution ........ ATC-6
A/C HFC134a (R134a) system service procedure .......
ATC-150
A/C HFC134a (R134a) system service tools ... ATC-17
A/C HFC134a system service equipment precaution ...
ATC-13
A/C lubricant (R134a) ...................................... ATC-26
A/C lubrication oil ........................................... ATC-173
A/C operational check ...................................... ATC-65
A/C self-diagnoses (auto A/C) ........ ATC-56, ATC-110
A/C service data specification ........................ ATC-173
A/C system description (auto A/C) ................... ATC-29
A/C trouble diagnoses (auto A/C) .................... ATC-40
A/C, A - Wiring diagram ................................... ATC-46
A/T fluid checking ...................... AT-13, AT-53, MA-29
A/T fluid cooler cleaning .................................... AT-14
A/T fluid replacement ............................. AT-12, MA-31
A/T fluid temperature sensor ........................... AT-135
A/T IND - Wiring diagram .................................... DI-56
A/T self-diagnoses ............................... AT-92, AT-103
A/T shift lock system ........................................ AT-229
A/T shift lock system - Wiring diagram ............ AT-230
A/T trouble diagnoses ........................................ AT-44
Accelerator control system ............................... ACC-3
Accelerator pedal position (APP) sensor ........ EC-617,
EC-624
, EC-638, EC-1336, EC-1343, EC-1357
Accelerator pedal released position learning .... EC-86,
EC-788
AF1B1-Wiring diagram ...... EC-237, EC-246, EC-255,
EC-265
, EC-648, EC-950, EC-959, EC-968, EC-978,
EC-1367
AF1B2-Wiring diagram ...... EC-239, EC-248, EC-257,
EC-267
, EC-650, EC-952, EC-961, EC-970, EC-980,
EC-1369
AF1HB1-Wiring diagram .................... EC-171, EC-884
AF1HB2-Wiring diagram .................... EC-173, EC-886
Air bag .............................................................. SRS-3
Air bag precautions ........................................... SRS-3
Air cleaner and air duct(VK45DE) ................... EM-177
Air cleaner and air duct(VQ35DE) .................... EM-19
Air cleaner filter replacement ............................ MA-25
Air cleaner filter replacement(VQ35DE) ........... MA-18
Air cleaner filter(VQ35DE) ................................ EM-20
Air conditioner cut control ................... EC-35, EC-737
Air flow meter - See Mass air flow sensor ....... EC-193,
EC-202
, EC-906, EC-915
Air fuel ratio sensor 1 ......... EC-234, EC-244, EC-253,
EC-262
, EC-646, EC-947, EC-957, EC-966, EC-975,
EC-1365
Air fuel ratio sensor 1 heater ............. EC-170, EC-883
Air mix. door motor ......................... ATC-82, ATC-140
Ambient sensor ............................. ATC-112, ATC-125
Angular tightening application ............................. EM-7
Angular tightening application(VK45DE) ........ EM-165
APPS1 - Wiring diagram ................. EC-619, EC-1338
APPS2 - Wiring diagram ................. EC-626, EC-1345
APPS3 - Wiring diagram ................. EC-640, EC-1359
ASC/BS - Wiring diagram ............... EC-578, EC-1291
ASC/SW - Wiring diagram .............. EC-561, EC-1274
ASCBOF - Wiring diagram .............. EC-658, EC-1378
ASCD .................................................. EC-36, EC-738
ASCD (automatic speed control device) ........... ACS-3
ASCIND - Wiring diagram ............... EC-665, EC-1385
AT indicator lamp ................................................ DI-55
Auto air conditioner - Wiring diagram ............. ATC-46
Auto amp ...................................................... ATC-124
Auto anti-dazzling inside mirror .......... GW-69, GW-70
Automatic amplifier ........... ATC-54, ATC-67, ATC-124
Automatic transmission fluid replacement ........ MA-32
AWD - Wiring diagram ....................................... TF-17
Axle ................................................................... MA-37
B
Back-up lamp ................................................... LT-245
Basic inspection .................................. EC-78, EC-780
Battery ................................................................. SC-4
Battery current sensor ....... EC-524, EC-531, EC-538,
EC-545
, EC-1237, EC-1244, EC-1251, EC-1258
Battery/Starting/Charging System Tester SC-7, SC-11,
SC-25
BCM (Body control module) .............................. BCS-3
Block heater(VK45DE) .................................... EM-252
Block heater(VQ35DE) ................................... EM-124
Blower motor ................................... ATC-88, ATC-131
Blower unit .................................................... ATC-129
Brake fluid level ................................................ MA-35
Brake hydraulic line ........................................... BR-11
Brake inspection ............................................... MA-36
Brake lines and cables inspection .................... MA-35
Brake pedal .......................................................... BR-6
Brake switch ................................... EC-589, EC-1307
BRK/SW - Wiring diagram .............. EC-591, EC-1309
Bulb specifications ........................................... LT-313
Bumper, front ...................................................... EI-11
Bumper, rear ....................................................... EI-14
C
Camshaft inspection(VK45DE) ....................... EM-217
Camshaft inspection(VQ35DE) ......................... EM-87

IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Camshaft position sensor (PHASE) EC-371, EC-1082
Camshaft(VK45DE) ......................................... EM-215
Camshaft(VQ35DE) ........................................... EM-85
CAN .................................................................. DI-109
CAN - Wiring diagram .......... EC-162, EC-866, AT-106
CAN (Controller Area Network) ... SB-5, BL-26, BL-59,
BL-221
, GW-19, GW-73, GW-95, SE-16
CAN communication ........... EC-161, EC-164, EC-740,
EC-865
, EC-868, AT-32, AT-105, TF-13, TF-32, SB-5,
BL-26
, BL-59, BL-221, GW-19, GW-73, GW-95, SE-16,
WW-11
Canister-See EVAP canister ............... EC-42, EC-744
Center bearing assembly (propeller shaft) ........ PR-12
Center bearing disassembly (propeller shaft) .... PR-11
CHARGE - Wiring diagram ................................ SC-22
Charging system ................................................ SC-20
Chassis and body maintenance ........................ MA-29
CHIME - Wiring diagram ..................................... DI-63
CIGAR - Wiring diagram .................................. WW-50
Cigarette lighter ............................................... WW-50
Circuit breaker ................................................... PG-17
Clock ................................................................. DI-107
CLOCK - Wiring diagram .................................. DI-107
Closed loop control .............................. EC-32, EC-734
Closed loop control (Bank 1) ........... EC-496, EC-1211
Closed loop control (Bank 2) ........... EC-496, EC-1211
Collision diagnosis ........................................... SRS-54
Combination lamp, front, removal and installation ........
LT-75
Combination lamp, rear, removal and installation ........
LT-265
Combination meter ............................................... DI-5
COMPAS - Wiring diagram ............................... DI-105
Compass .......................................................... DI-102
Component Location (auto A/C) ...................... ATC-42
Compression pressure(VK45DE) .................... EM-235
Compression pressure(VQ35DE) .................... EM-102
Compressor special service tool ...................... ATC-16
Condenser ..................................................... ATC-164
Connecting rod bearing clearance(VK45DE) .. EM-275
Connecting rod bushing clearance .................. EM-143
Connecting rod bushing clearance(VK45DE) .. EM-271
Connecting rod(VK45DE) ................................ EM-271
Connecting rod(VQ35DE) ................................ EM-141
CONSULT-II Reference value (A/T) .................. AT-90
Control units (terminal arrangement) ............... PG-107
Control valve (A/T) ............................................. AT-38
Controller Area Network (CAN) ... SB-5, BL-26, BL-59,
BL-221
, GW-19, GW-73, GW-95, SE-16
Converter housing installation ............ AT-277, AT-280
COOL/F - Wiring diagram ................ EC-502, EC-1217
Coolant replacement(VQ35DE) ......................... MA-15
Cooling circuit (engine)(VK45DE) ...................... CO-38
Cooling circuit (engine)(VQ35DE) ....................... CO-9
Cooling fan motor ............................ EC-509, EC-1224
Cooling fan(VK45DE) ........................................ CO-51
Cooling fan(VQ35DE) ........................................ CO-22
Cowl top ............................................................... EI-18
Cowl top cover ..................................................... EI-18
Crankcase ventilation system - See Positive crankcase
ventilation ............................................. EC-51
, EC-753
Crankshaft position sensor (POS) ... EC-364, EC-1075
Crankshaft(VK45DE) ...................................... EM-253
Crankshaft(VQ35DE) ...................................... EM-141
Crash zone sensor .......................................... SRS-49
CUR/SE - Wiring diagram .. EC-526, EC-533, EC-540,
EC-547
, EC-1239, EC-1246, EC-1253, EC-1260
Cylinder block boring(VK45DE) ...................... EM-274
Cylinder block(VK45DE) ................................. EM-252
Cylinder block(VQ35DE) ................................. EM-124
Cylinder head bolt tightening(VK45DE) .......... EM-237
Cylinder head bolt tightening(VQ35DE) .......... EM-105
Cylinder head(VK45DE) ................................. EM-235
Cylinder head(VQ35DE) ................................. EM-102
D
D/LOCK - Wiring diagram .................................. BL-28
Daytime light system ........................................... LT-78
Daytime running light - See Daytime light system LT-78
DEF - Wiring diagram ............................ SB-7, SE-119
Diagnosis sensor unit ..................................... SRS-52
Diagnostic trouble code (DTC) for OBD system EC-16,
EC-59
, EC-718, EC-761
Direct clutch solenoid valve ............... AT-155, AT-157
Display and amp.assembly ............... ATC-54, ATC-67
Door glass ........................................... GW-61, GW-65
Door glass Fitting Adjustment(Front) ................ GW-64
Door glass Fitting Adjustment(Rear) ................. GW-68
Door lock .......................................................... BL-194
Door mirror ...................................................... GW-118
Door trim ............................................................. EI-34
Door, front ........................................... BL-188, GW-61
Door, rear ............................................ BL-188, GW-65
Drive belt inspection ......................................... MA-22
Drive belt(VK45DE) ........................................ EM-174
Drive belt(VQ35DE) .......................................... EM-16
Drive shaft ......................................................... MA-38
Drive shaft (rear) ............................................... RAX-8
Driver air bag .................................................. SRS-42
DTRL - Wiring diagram ....................................... LT-83
Duct and grilles .............................................. ATC-143
E
ECM power supply EC-154
, EC-479, EC-858, EC-1186
ECM/PW - Wiring diagram ............... EC-480, EC-1187
ECTS - Wiring diagram ...................... EC-216, EC-928
Electric sunroof .................................................. RF-10
Electric throttle control actuator ........ EC-604, EC-615,
EC-1322
, EC-1334
Electric throttle control actuator (VK45DE) ..... EM-179
Electric throttle control actuator (VQ35DE) ....... EM-21
Electrical load signal circuit .............. EC-667, EC-1387
Electrical unit ................................................... PG-107
Electrical units location ...................................... PG-98
Electronic ignition (EI) system ............. EC-33, EC-735
Engine control module (ECM) .......... EC-483, EC-1190

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
EC-890
Heated seat ..................................................... SE-144
Heater and cooling unit (Heater core) ........... ATC-134
HFC134a (R134a) system precaution ............... ATC-6
HFC134a (R134a) system service procedure ATC-150
HFC134a (R134a) system service tools .......... ATC-17
HFC134a system service equipment precaution ..........
ATC-13
High and low reverse clutch solenoid valve .... AT-159,
AT-161
Hood ................................................................... BL-15
Horn ................................................................. WW-54
HORN - Wiring diagram ................................... WW-54
How to erase DTC for OBD system ..... EC-68, EC-770
HSEAT - Wiring diagram ................................. SE-147
I
IATS - Wiring diagram ....................... EC-211
, EC-923
ICC - Wiring diagram ....................................... ACS-23
ICC/BS - Wiring diagram ................. EC-569, EC-1282
ICC/SW - Wiring diagram ................ EC-554, EC-1267
ICCBOF - Wiring diagram ................ EC-684, EC-1404
Idle air volume learning ....................... EC-86, EC-788
Idle speed .............................. EC-78, EC-780, EC-785
Idle speed control (ISC) .... EC-470, EC-472, EC-1177,
EC-1179
Ignition coil ....................................... EC-691, EC-1411
Ignition coil(VK45DE) ...................................... EM-190
Ignition coil(VQ35DE) ........................................ EM-44
Ignition control system ..................... EC-691, EC-1411
Ignition timing ........................ EC-78, EC-780, EC-785
IGNSYS - Wiring diagram ................ EC-692, EC-1412
Illumination ....................................................... LT-293
Illumination control ................. LT-289, LT-290, LT-291
In vehicle sensor ........................... ATC-115, ATC-126
INJECT - Wiring diagram ................. EC-670, EC-1390
Injector ............................................................. EC-669
Input clutch solenoid valve ................. AT-147, AT-149
Instrument panel .................................................. IP-10
Intake air temperature sensor ........... EC-209, EC-229,
EC-922
, EC-942
Intake door control linkage adjustment ............ ATC-87
Intake door motor ........................... ATC-85, ATC-132
Intake manifold collector(VQ35DE) ................... EM-21
Intake manifold(VK45DE) ................................ EM-179
Intake manifold(VQ35DE) .................................. EM-26
Intake sensor ................................ ATC-121, ATC-128
Intake valve timing control (Bank 1) .. EC-166, EC-870
Intake valve timing control (Bank 2) .. EC-166, EC-870
Intake valve timing control position sensor (Bank 1) ....
EC-1203
Intake valve timing control position sensor (Bank 2) ....
EC-1203
Intake valve timing control solenoid valve (Bank 1) ......
EC-185
, EC-899
Intake valve timing control solenoid valve (Bank 2) ......
EC-185
, EC-899
Integrated homelink transmitter ........................ BL-278
Intelligent cruise control (ICC) system .............. ACS-6
Interior ................................................................. EI-37
Interior lamp ...................................................... LT-266
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-18
IVCB1 - Wiring diagram ..................... EC-186, EC-900
IVCB2 - Wiring diagram ..................... EC-188, EC-902
IVCSB1 - Wiring diagram ............................... EC-1204
IVCSB2 - Wiring diagram ............................... EC-1206
IVTB1 - Wiring diagram ................................... EC-873
IVTB2 - Wiring diagram ................................... EC-875
K
Knock sensor (KS) ........................... EC-359
, EC-1070
KS - Wiring diagram ......................... EC-360, EC-1071
L
LAN system circuit ........................................... ATC-71
Lane Departure Warning System ....................... DI-75
Laser beam aiming adjustment ....................... ACS-15
Latch (lower anchors and tether for children) system ...
SB-35
LDW .................................................................... DI-75
LDW - Wiring Diagram ........................................ DI-86
License lamp ..................................................... LT-248
Line pressure solenoid valve ........................... AT-130
Line pressure test (A/T) ..................................... AT-55
Liquid gasket application .................................... EM-8
Liquid gasket application(VQ35DE) LU-3, LU-23, CO-3
Location of electrical units ................................. PG-98
Low coast brake solenoid valve ......... AT-163, AT-165
Lubricant (R134a) A/C ..................................... ATC-26
Lubrication circuit (engine)(VK45DE) ................ LU-25
Lubrication circuit (engine)(VQ35DE) .................. LU-5
Lubrication oil A/C .......................................... ATC-173
M
MAFS - Wiring diagram ..... EC-196
, EC-204, EC-909,
EC-917
Magnet clutch .................................................. ATC-93
MAIN - Wiring diagram ........ EC-154, EC-858, AT-180
Maintenance (engine)(VQ35DE) ...................... MA-14
Major overhaul (Final drive) .............. FFD-15, RFD-18
Major overhaul (Transfer) .................................. TF-45
Malfunction indicator lamp (MIL) .......... EC-70, EC-772
Manual mode switch ........................................ AT-167
Mass air flow sensor (MAFS) ............ EC-193, EC-202,
EC-906
, EC-915
Meter ..................................................................... DI-5
METER - Wiring diagram .................................... DI-13
MIL data link connectors circuit ....... EC-714, EC-1438
MIL/DL - Wiring diagram .................. EC-714, EC-1438
MIRROR - Wiring diagram ................................ GW-97
Mirror, door ..................................................... GW-118
Mirror, out side ................................................ GW-118
Misfire .............................................. EC-349, EC-1061

IDX-7
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Refrigerant general precaution .......................... ATC-7
Refrigerant lines ............................................ ATC-150
Refrigerant pressure sensor ........... EC-704, EC-1424,
ATC-97
, ATC-166
Refrigeration cycle ........................................... ATC-20
Removal and installation (A/T) ........... AT-274, AT-278
Removal and installation (Transfer) .................... TF-44
Reverse interlock door mirror ........................... GW-94
Revolution sensor (A/T) ...................... AT-119, AT-263
Rocker cover(VK45DE) ................................... EM-199
Rocker cover(VQ35DE) ..................................... EM-53
Room lamp - See Interior lamp ......................... LT-266
ROOM/L - Wiring diagram ................................ LT-273
RP/SEN - Wiring diagram ................ EC-705, EC-1425
S
SAE J1979 - Service $01 - 09 ............. EC-54
, EC-756
SEAT - Wiring diagram ...................................... SE-99
Seat belt inspection ........................................... SB-32
Seat belt, front ................................................... SB-29
Seat belt, rear .................................................... SB-31
Seat, rear ......................................................... SE-173
Self-diagnosis (Transfer) .................................... TF-22
SEN/PW - Wiring diagram ............... EC-487, EC-1194
SHIFT - Wiring diagram ................................... AT-230
Shift lock system .............................................. AT-229
Shock absorber (rear) ..................................... RSU-10
Side air bag (satellite) sensor .......................... SRS-50
Side curtain air bag .......................................... SRS-47
Side trim .............................................................. EI-37
SMJ (super multiple junction) .......................... PG-109
Spark plug replacement ..................................... MA-27
Spark plug replacement(VQ35DE) .................... MA-20
Spark plug(VK45DE) ....................................... EM-191
Spark plug(VQ35DE) ......................................... EM-45
Specification value ............................. EC-143, EC-847
Speedometer ........................................................ DI-5
Spiral cable ...................................................... SRS-44
SROOF - Wiring diagram .................................. RF-13
SRS - See Supplemental Restraint System ...... SRS-5
SRS - Wiring diagram ...................................... SRS-13
SRS Trouble diagnoses ..................................... SRS-9
Stabilizer bar (rear) ......................................... RSU-17
Stall test (A/T) .................................................... AT-53
Standardized relay ........................................... PG-112
START - Wiring diagram ..................................... SC-9
Starter .................................................................. SC-8
Starting system .................................................... SC-8
Steering gear and linkage inspection ................ MA-36
Steering wheel and column ................... PS-10, PS-13
Steering wheel turning force .............................. PS-10
Stop lamp ......................................................... LT-242
Stop lamp switch ............................. EC-589, EC-1307
STSIG - Wiring diagram .................................. AT-109
Sun roof, electric ................................................ RF-10
Sunload sensor ............................. ATC-118, ATC-127
Sunroof .................................................. RF-24, RF-27
Sunshade ............................................................ EI-44
Supplemental Restraint System ....................... SRS-5
Supplemental restraint system - Wiring diagram ..........
SRS-13
Suspension ....................................................... MA-37
Symbols and abbreviations ...................... GI-11, GI-24
System readiness test (SRT) code ...... EC-60, EC-762
T
Tachometer ........................................................... DI-5
Tail lamp ........................................................... LT-248
TCM circuit diagram ........................................... AT-52
TCM inspection table ......................................... AT-89
Thermostat(VK45DE) ....................................... CO-55
Thermostat(VQ35DE) ....................................... CO-29
Three way catalyst function (Bank 1) EC-380, EC-1089
Three way catalyst function (Bank 2) EC-380, EC-1089
Three way catalyst precautions ............................ GI-5
Three way catalyst(VK45DE) .......................... EM-183
Throttle control motor ....................... EC-610, EC-1329
Throttle control motor relay .............. EC-598, EC-1316
Throttle position sensor (TPS) .......... EC-219, EC-342,
EC-518
, EC-520, EC-631, EC-932, EC-1054, EC-1233,
EC-1235
, EC-1350
Throttle valve closed position learning . EC-86, EC-788
Tie-rod ............................................................... PS-19
Timing chain(VK45DE) ................................... EM-203
Timing chain(VQ35DE) ..................................... EM-66
Tire rotation ....................................................... MA-35
TLID - Wiring diagram ...................................... BL-209
Top tether strap child restraint ........................... SB-36
Torque converter installation ............. AT-277, AT-280
Torque convertor clutch solenoid valve AT-126, AT-128
TPS1 - Wiring diagram .................... EC-344, EC-1056
TPS2 - Wiring diagram ...................... EC-221, EC-934
TPS3 - Wiring diagram .................... EC-633, EC-1352
Transfer control unit inspection table ................. TF-20
TRNSCV - Wiring diagram ............................... BL-278
Trouble diagnoses .............................................. GI-12
Trunk lid ........................................................... BL-201
Trunk lid opener - See Trunk lid ...................... BL-207
TURN - Wiring diagram .................................... LT-216
Turn signal lamp ............................................... LT-212
Two trip detection logic ........................ EC-54, EC-756
Tyre pressure monitoring system - trouble diagnoses ..
WT-12
U
Unified meter and A/C amp. ............................... DI-28
Upper link (front susp.) ..................... FSU-16, FSU-34
V
Vacuum hose (brake system) ............................ BR-20
Valve clearance(VK45DE) .............................. EM-224
Valve clearance(VQ35DE) ................................ EM-94
Valve guide ..................................................... EM-109
Valve guide(VK45DE) ..................................... EM-243

IP-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: 2007 April2007 M35/M45
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30×50 mm (1.18×1.97 in)
FELT CLOTHTAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15×25 mm (0.59×0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit. Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingNIS0025A
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the Nissan Squeak and Rattle Kit (J-43980) to repair the noise.

INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
MA
B
IP
Revision: 2007 April2007 M35/M45
Removal and Installation of Instrument Panel & PadNIS0025D
REMOVAL
1. Remove cup holder.

Backside pull up.
2. Remove switch finisher.

Disconnect harness connector.
3. Remove A/T console finisher.

Place the selector lever in "D" position.

Remove selector lever knob. Refer to AT- 2 2 2 , "Control Device
Removal and Installation" .

Lift up backside and pull back.

Disconnect harness connector.
4. Remove cluster lid C.

Pull back.

Disconnect harness connector.
1. Cup holder 2. Switch finisher 3. A/T console finisher
4. Cluster lid C 5. Console rear finisher 6. Center console
7. Glove box 8. Instrument passenger lower cover 9. Instrument side finisher (RH)
10. Glove box cover 11. Instrument finisher B 12. Instrument side finisher (LH)
13. Instrument driver lower panel 14. Instrument finisher A 15. Instrument finisher C
16. Cluster lid A 17. Combination meter 18. Steering column cover
19. Upper ventilator gurille 20. Center ventilator grille 21. Multifunction switch
22. Front display unit 23. Audio assembly 24. NAVI C/U
25. Side ventilator grille (RH/LH) 26. Front defroster grille 27. Instrument panel & pad
Pawl Clip Metal clip
PIIB4107J
PIIB4108E
PIIB4109E

IP-14
INSTRUMENT PANEL ASSEMBLY
Revision: 2007 April2007 M35/M45
20. Remove center ventilator grille.

Insert a remover into rear lower space.

Pull up.
21. Remove multifunction switch. Refer to AV- 2 8 4 , "
Multifunction Switch" .
22. Remove front display unit. Refer to AV- 2 8 3 , "
Front Display Unit" .
23. Remove audio assembly. Refer to AV- 2 7 7 , "
Audio Unit" .
24. Remove NAVI C/U. Refer to AV- 2 8 2 , "
AV (NAVI) Control Unit" .
25. Remove side ventilator grille (RH/LH).

Insert a remover into lower space.

Pull back.
26. Remove front defroster grille.

Insert a remover into back space.

Disconnect harness connector.
27. Remove instrument panel & pad.

Remove front passenger air bag module mounting bolt and disconnect harness connector. Refer to
SRS-46, "
FRONT PASSENGER AIR BAG MODULE" .

Remove front pillar garnish. Refer to EI-38, "FRONT PILLAR GARNISH" .
INSTALLATION
Install in the reverse order of removal.
CAUTION:

To install, confirm locating pins on back of instrument panel are completely inserted into holes on
vehicle.

Do not leave harness stuck when installing.
PIIB4121E
PIIB4123E
PIIB4122E

LAN-2Revision: 2007 April2007 M35/M45 CAN System (Type 7) ............................................. 76
DIAGNOSIS SHEET ............................................ 76
CAN System (Type 8) ............................................. 77
DIAGNOSIS SHEET ............................................ 77
CAN System (Type 9) ............................................. 78
DIAGNOSIS SHEET ............................................ 78
CAN System (Type 10) ........................................... 79
DIAGNOSIS SHEET ............................................ 79
CAN System (Type 11) ........................................... 80
DIAGNOSIS SHEET ............................................ 80
Component Parts Location ..................................... 81
Harness Layout ...................................................... 81
Malfunction Area Chart ........................................... 82
MAIN LINE ........................................................... 82
BRANCH LINE .................................................... 82
SHORT CIRCUIT ................................................ 82
Main Line Between TCM and Data Link Connector ... 83
Main Line Between Data Link Connector and Pre-
crash Seat Belt Control Unit ................................... 84
Main Line Between Data Link Connector and RAS
Control Unit ............................................................. 85
Main Line Between RAS Control Unit and Pre-crash
Seat Belt Control Unit ............................................. 86
Main Line Between Pre-crash Seat Belt Control Unit
and Driver Seat Control Unit ................................... 87
Main Line Between Driver Seat Control Unit and ABS Actuator and Electric Unit (Control Unit) ......... 88
Main Line Between ABS Actuator and Electric Unit
(Control Unit) and ICC Sensor Integrated Unit ....... 89
ECM Branch Line Circuit ......................................... 89
AWD Control Unit Branch Line Circuit .................... 90
AFS Control Unit Branch Line Circuit ...................... 91
BCM Branch Line Circuit ......................................... 91
LDW Camera Unit Branch Line Circuit ................... 92
TCM Branch Line Circuit ......................................... 93
NAVI Control Unit Branch Line Circuit .................... 93
AV Control Unit Branch Line Circuit ........................ 94
Data Link Connector Branch Line Circuit ................ 95
Intelligent Key Unit Branch Line Circuit ................... 95
Unified Meter and A/C Amp. Branch Line Circuit .... 96
Steering Angle Sensor Branch Line Circuit ............. 97
Low Tire Pressure Warning Control Unit Branch Line
Circuit ...................................................................... 97
RAS Control Unit Branch Line Circuit ..................... 98
Pre-Crash Seat Belt Control Unit Branch Line Circuit
... 99
Driver Seat Control Unit Branch Line Circuit ........... 99
ABS Actuator and Electric Unit (Control Unit) Branch
Line Circuit ............................................................100
ICC Sensor Integrated Unit Branch Line Circuit ...101
IPDM E/R Branch Line Circuit ...............................101
CAN Communication Circuit .................................102