tow INFINITI Q70 2017 Quick Reference Guide

8
5
6
Cruise Control
3
2
1
4
3
2 1
CONVENTIONAL CRUISE CONTROL (if so equipped)
SETTING A CRUISING SPEED
•


Press

the CRUISE ON/OFF switch
1 to turn on the system.
•


With the vehicle at the desired speed, push down the switch 2 to COAST/SET to enable
cruise control.
•


The cruising speed can be adjusted to a higher or lower speed by togglin\
g the control
switch
2 up or down.
CANCELING THE PRESET SPEED
•


Push

the CANCEL switch
3 or tap the brake pedal.
INTELLIGENT CRUISE CONTROL (ICC) (if so equipped)
The ICC system is designed to maintain a selected distance from the vehi\
cle in front of you and
reduce the speed to match a slower vehicle ahead.
•


To increase the distance to the vehicle ahead to be maintained by the IC\
C system, press
the button
4 until the display shows the desired set distance, which is shown by the
number of lines on the indicator
5.
•


When a vehicle is detected ahead, a car icon will illuminate on the indi\
cator 6 and your
vehicle will reduce the speed to match the slower vehicle.
To use Conventional (fixed speed) Cruise Control mode (if so equipped\
)
•


While cruise control is off, push and hold the CRUISE ON/OFF

switch
1 for more than
1.5 seconds. The CRUISE indicator light will illuminate.
• Accelerate to the desired speed.
•


Push the switch 2 down toward COAST/SET and release it. The SET indicator light
will illuminate.
Please see your Owner’s Manual for important safety information, syst\
em limitations, and additional operating and
feature information.
INTELLIGENT CRUISE CONTROL (ICC) (if so equipped)
2586986_17a_Q70_US_pQRG_090916.indd 89/9/16 4:04 PM

14
Move the lever 1 up or down to one of
the following positions to operate the
windshield wipers:
MIST
One sweep operation
OFF



Wipers are OFF
AUTO



Speed-sensing and rain-sensing
automatic wipe
LO



Continuous wipe, slow
HI
Continuous wipe, fast
To adjust the wiper sensitivity for the AUTO
setting, twist the control ring
2.
Pull the lever
1 toward you operate the
windshield washer.
To turn the rain-sensing automatic wiper system
off, push up the lever to the OFF position, or pull
down the lever to the LO or HI position.
Wiper and Washer Switch
1
2
SYSTEM OPERATING TIPS •
The interior of the vehicle should be as quiet as possible.
•


Speak naturally. Speaking too fast, too slow, too soft, or
too loud makes voice recognition more difficult.
•


Confirm that the correct voice commands are
being used. Glance at the screen to see the currently
available commands.
USING THE VOICE RECOGNITION SYSTEM
•


Press
the
button 1 on the steering wheel, and a list
of commands will appear on the screen.
•


After the tone sounds, speak the command.
•


To skip the voice prompt and give the command
immediately, press the button 1 on the steering
wheel to interrupt the system. Speak the next command
after the tone sounds.
•


To cancel the command, press and hold the button 1 on the steering wheel.
Please see your Owner’s Manual for important safety information, syst\
em
limitations, and additional operating and feature information.
Voice Recognition

1
PULLING UP THE WIPER ARM
The wiper arm should be in the UP
position when replacing the wiper.
• With the shift lever in the P (PARK)
position, place the ignition switch


in the OFF position.
•


Within 1 minute, push the wiper
switch to the MIST

position twice.
The wiper operation stops in mid-
operation and the wiper arm can
be pulled up.
•


To return the wiper arm, place
the wiper arm in the DOWN
position and operate the wiper
switch once.
Please see your Owner’s Manual for important safety information, syst\
em limitations, and additional operating and
feature information.
2586986_17a_Q70_US_pQRG_090916.indd 149/9/16 4:05 PM