display INFINITI QX 2011 Owners Manual

The LDW system is not designed to warn under
the following conditions.
– When you operate the lane change signaland change traveling lanes in the direction of
the signal. (The LDW system will become
operable again approximately 2 seconds af-
ter the lane change signal is turned off.)
– When the vehicle speed lowers to less than approximately 45 MPH (70 km/h).
After the above conditions have finished and
the necessary operating conditions are satis-
fied, the LDW functions will resume.
Turning on or off the LDW system (Type A) :
The LDW system is automatically turned on
when the engine is started and the warning
systems ON indicator light
1illuminates on
the warning systems switch. You can turn the
LDW system off by pushing the warning sys-
tems switch on the instrument panel. This
switch will turn on and off the LDW, BSW and
FCW systems at the same time. NOTE:
If you continue to push the warning systems
switch from off to on for over 4 seconds, a chime
will sound. This will change the default status of
the LDW, BSW and FCW systems to OFF so that
these systems will not automatically turn on
when the engine is started. If this procedure is
repeated, the default status will return to ON.
Turning on or off the LDW system (Type B) :
The warning systems switch is used to turn on
and off the LDW system when it is activated
using the settings menu on the center display.
See “How to enable/disable the LDW system
using the settings menu (Type B)” later in this
section.
When the warning systems switch is turned off,
the indicator
1on the switch is off. The
indicator will also be off if the LDW, the Blind
Spot Warning (BSW) and the Forward Collision
Warning (FCW) systems are deactivated.
For the BSW and FCW systems, see “BLIND
SPOT WARNING (BSW) SYSTEM” later in this
section and “FORWARD COLLISION WARNING
(FCW) SYSTEM” later in this section.
Warning systems switch
SSD0956
5-22Starting and driving

How to enable/disable the LDW system using
the settings menu (Type B) :
Perform the following steps to enable or disable
the LDW system.
1. Push the SETTING1button and highlight
the “Driver Assistance” key on the display
using the INFINITI controller. Then push
the ENTER
2button.
2. Highlight the “Driver Assistance Warn- ings” key, and push the ENTER
2button.
3. Highlight the “Lane Departure Warning”key, select ON (enabled) or OFF (disabled)
and push the ENTER
2button.
Temporary disabled status at high
temperature
If the vehicle is parked in direct sunlight under
high temperature conditions (over approxi-
mately 104°F (40°C) and then started, the LDW
system may be deactivated automatically. The
lane departure warning light (orange) will flash.
When the interior temperature is reduced, the
LDW system will resume operating automati-
cally and the lane departure warning light (or-
ange) will stop flashing.
With navigation system
SSD0959
SSD1102
JVS0080X
Starting and driving5-23

The warning and assist functions will stop when
the vehicle returns to a position inside of the
lane marker.The LDP system turns on when the dynamic
driver assistance switch on the steering wheel
is pushed when “Lane Departure Prevention” is
enabled in the settings menu on the center
display. The LDP ON indicator light (green) on
the instrument panel will illuminate.
Dynamic driver assistance switch
SSD0957
SSD0959
SSD1102
5-26Starting and driving

How to enable/disable the LDP system using
the settings menu :
Perform the following steps to enable or disable
the LDP system.
1. Push the SETTING1button and highlight
the “Driver Assistance” key on the display
using the INFINITI controller. Then push
the ENTER
2button.
2. Highlight the “Dynamic Assistance Set- tings” key, and push the ENTER
2but-
ton.
3. Highlight the “Lane Departure Preven-tion” key, select ON (enabled) or OFF
(disabled) and push the ENTER
2button.
For the DCA system, see “DISTANCE CONTROL
ASSIST (DCA) SYSTEM” later in this section.
Automatic deactivation
Condition A :
The warning and assist functions of the LDP
system are not designed to work under the
following conditions:
●When you operate the lane change signal
and change the traveling lanes in the direc- tion of the signal. (The LDP system will be
deactivated for approximately 2 seconds af-
ter the lane change signal is turned off.)
● When the vehicle speed lowers to less than
approximately 45 MPH (70 km/h).
After the above conditions have finished and the
necessary operating conditions are satisfied, the
warning and assist functions will resume.
Condition B :
The assist function of the LDP system is not
designed to work under the following condi-
tions (warning is still functional):
● When the brake pedal is depressed.
● When the steering wheel is turned as far as
necessary for the vehicle to change lanes.
● When the accelerator pedal is depressed
while the brake control assist is provided.
● When the Intelligent Cruise Control (ICC)
approach warning occurs.
● When the hazard warning flashers are oper-
ated.
● When driving on a curve at high speed.
After the above conditions have finished and
the necessary operating conditions are satis-
fied, the LDP brake control assist function will
resume.
SSD1103
Starting and driving5-27

The brightness of the BSW indicator lights is
adjusted automatically depending on the
brightness of the ambient light.
A chime sounds if the radar sensors have
already detected vehicles when the driver acti-
vates the turn signal. If a vehicle comes into the
detection zone after the driver activates the turn
signal, then only the BSW indicator light flashes
and no chime sounds. (See “BSW DRIVING
SITUATIONS” later in this section)
Turning on or off the BSW system
(Type A)
The BSW system is automatically turned on
when the engine is started and the warning
systems ON indicator light
1illuminates on
the warning systems switch. You can turn the
BSW system off by pushing the warning sys-
tems switch on the instrumental panel. This
switch will turn on and off the LDW, BSW and
FCW systems at the same time. NOTE:
If you continue to push the warning systems
switch from off to on for over 4 seconds, a chime
will sound. This will change the default status of
the LDW, BSW and FCW systems to OFF so that
these systems will not automatically turn on
when the engine is started. If this procedure is
repeated, the default status will return to ON.
Turning on or off the BSW system
(Type B)
The warning systems switch is used to turn on
and off the BSW system when it is activated
using the settings menu on the center display.
See “How to enable/disable the BSW system
using the settings menu” later in this section.
When the warning systems switch is turned off,
the indicator
1on the switch is off. The
indicator will also be off if the BSW, the Lane
Departure Warning (LDW) and the Forward Col-
lision Warning (FCW) systems are deactivated.
For the LDW and FCW systems, see “LANE
DEPARTURE WARNING (LDW)/PREVENTION (LDP)
SYSTEM” earlier in this section and “FORWARD
COLLISION WARNING (FCW) SYSTEM” later in
this section.
Warning systems switch
SSD0956
Starting and driving5-31

How to enable/disable the BSW system using
the settings menu :
Perform the following steps to enable or disable
the BSW system.
1. Push the SETTING1button and highlight
the “Driver Assistance” key on the display
using the INFINITI controller. Then push
the ENTER
2button.
2. Highlight the “Driver Assistance Warn- ings” key, and push the ENTER
2button.
3. Highlight the “Blind Spot Warning” key,select ON (enabled) or OFF (disabled) and
push the ENTER
2button.
BSW system precautions
WARNING
●Do not use the BSW system when towing a
trailer because the system may not function
properly.
● Excessive noise (e.g. audio system volume,
open vehicle window) will interfere with the
chime sound, and it may not be heard.
SSD0959
SSD1102
JVS0080X
5-32Starting and driving

●In the conventional (fixed speed) cruise con-
trol mode, a warning chime will not sound to
warn you if you are too close to the vehicle
ahead. Pay special attention to the distance
between your vehicle and the vehicle ahead
of you or a collision could occur.
1. Vehicle-to-vehicle distance control mode
2. Conventional (fixed speed) cruise control
mode
Push the MAIN switchAto choose the cruise
control mode between the vehicle-to-vehicle
distance control mode
1and the conventional
(fixed speed) cruise control mode
2.
To choose the vehicle-to-vehicle distance con-
trol mode
1, quickly push and release the
MAIN switch
A. To choose the conventional
(fixed speed) cruise control mode
2, push and
hold the MAIN switch
Afor longer than ap-
proximately 1.5 seconds. Once a control mode is activated, it cannot be
changed to the other cruise control mode. To
change the mode, push the MAIN switch once to
turn the system off. Then push the MAIN switch
again to turn the system back on and select the
desired cruise control mode.
Always confirm the setting in the ICC system
display.
For the vehicle-to-vehicle distance control
mode, see the following description. For the
conventional (fixed speed) cruise control mode,
see “CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE” later in this section.
SSD1051
5-40Starting and driving

VEHICLE-TO-VEHICLE DISTANCE
CONTROL MODE OPERATION
Always pay attention to the operation of the
vehicle and be ready to manually control the
proper following distance. The vehicle-to-
vehicle distance control mode of the Intelligent
Cruise Control (ICC) system may not be able to
maintain the selected distance between ve-
hicles (following distance) or selected vehicle
speed under some circumstances.
The vehicle-to-vehicle distance control mode
uses a sensor
Alocated on the front of the
vehicle to detect vehicles traveling ahead. The
sensor generally detects the signals returned
from the reflectors on a vehicle ahead. There- fore, if the sensor cannot detect the reflector on
the vehicle ahead, the ICC system may not
maintain the selected distance.
The following are some conditions in which the
sensor cannot detect the signals:
●
When the reflector of the vehicle ahead is
positioned high on the vehicle (trailer, etc.)
● When the reflector on the vehicle ahead is
missing, damaged or covered
● When the reflector of the vehicle ahead is
covered with dirt, snow and road spray
● When the snow or road spray from traveling
vehicles reduces the sensor’s visibility
● When dense exhaust or other smoke (black
smoke) from vehicles reduces the sensor’s
visibility
● When excessively heavy baggage is loaded
in the rear seat or the trunk of your vehicle
● When your vehicle is towing a trailer, etc.
The ICC system is designed to automatically
check the sensor’s operation within the limita-
tion of the system. When the sensor is covered
with dirt or obstructs, the system will automati-
cally be canceled. If the sensor is covered with
ice, a transparent or translucent vinyl bag, etc.,
the ICC system may not detect them. In these
instances, the vehicle-to-vehicle distance con- trol mode may not cancel and may not be able
to maintain the selected following distance
from the vehicle ahead. Be sure to check and
clean the sensor regularly.
The vehicle-to-vehicle distance control mode is
designed to maintain a selected distance and
reduce the speed to match the slower vehicle
ahead; the system will decelerate the vehicle as
necessary, and if the vehicle ahead comes to a
stop, the vehicle decelerates to a standstill.
However, the ICC system can only apply up to
25% of the vehicles total braking power. This
system should only be used when traffic condi-
tions allow vehicle speeds to remain fairly
constant or when vehicle speeds change gradu-
ally. If a vehicle moves into the traveling lane
ahead or if a vehicle traveling ahead rapidly
decelerates, the distance between vehicles may
become closer because the ICC system cannot
decelerate the vehicle quickly enough. If this
occurs, the ICC system will sound a warning
chime and blink the system display to notify the
driver to take necessary action.
The system will cancel and a warning chime will
sound if the speed falls below approximately 15
MPH (24 km/h) and a vehicle is not detected
ahead. The system will also disengage when
the vehicle goes above the maximum set speed.
See “Approach warning” later in this section.
SSD1047
Starting and driving5-43

Intelligent Cruise Control (ICC) system
switch
The system is operated by a MAIN switch and
four control switches, all mounted on the steer-
ing wheel.
1. RESUME/ACCELERATE switch:
Resumes set speed or increases speed incre-
mentally.
2. SET/COAST switch:
Sets desired cruise speed, reduces speed
incrementally.
3. CANCEL switch:
Deactivates the system without erasing the
set speed.
4. DISTANCE switch:
Changes the vehicle’s following distance:
● Long
● Middle
● Short
5. MAIN switch:
Master switch to activate the system
Intelligent Cruise Control (ICC) system
display and indicators
The display is located between the speedom-
eter and tachometer.
1. MAIN switch indicator:
Indicates that the MAIN switch is ON.
2. Vehicle ahead detection indicator:
Indicates whether it detects a vehicle in
front of you.
3. Set distance indicator:
Displays the selected distance between ve-
hicles set with the DISTANCE switch.
SSD0964SSD1104
Starting and driving5-47

4. Indicates your vehicle
5. Set vehicle speed indicator:
Indicates the set vehicle speed.
For Canadian models, the speed is displayed
in km/h.
6. Intelligent Cruise Control (ICC) systemwarning light (orange):
The light comes on if there is a malfunction
in the ICC system.
When the ignition switch is pushed to the ON
position, the indicators come on as illustrated
to check for a burned-out bulb, and it turns off
when the engine is started.
Operating vehicle-to-vehicle distance
control mode
To turn on the cruise control,quickly push and
release the MAIN switch
Aon. The MAIN
switch indicator, set distance indicator and set
vehicle speed indicator come on and in a
standby state for setting.
SSD0979SSD1052
5-48Starting and driving