Button INFINITI QX30 2017 Manual PDF

AUTOMATIC CLIMATE CONTROL
(2–ZONE)
1Sets the temperature, left
2Sets climate control to automatic mode
3Demists the windshield
4Increases the airflow
5Sets the air distribution
6Display
7Activates/deactivates air-recirculation
mode
8Switches climate control on/off
9Sets the temperature, right
10Activates/deactivates the Max Cool func-
tion
11Activates/deactivates cooling with air de-
humidification
12Reduces the airflow
13Switches the rear window heating on/off
14Switches the ZONE function on/off
Operating tips
A number of tips and recommendations to
enable you to get the most out of your auto-
matic climate control are listed below:
•Activate climate control using theandbuttons. The indicator lamps in theandbuttons light up.
•Set the temperature to 70oF (22oC)
•Only use the Windshield demisting function
briefly until the windshield is clear again.
•Only use air-recirculation mode briefly, e.g. if
there are unpleasant outside odors or when
in a tunnel. The windows could otherwise
mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•Use thefunction to adopt the tempera-
ture settings on the driver’s side for the
front-passenger side as well. The indicator
lamp in the
button goes out.
NAA1705
Display screen, heater and air conditioner, and audio system4-47

•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the center display
(see separate operating instructions). You
will see the current settings of the various
climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (seeIdle Stop/Start
System (if equipped) in the5. Starting and
driving section).
Switching automatic climate control
on/off
When the climate control is switched off, the air
supply and air circulation are also switched off.
The windows could mist up. Therefore, only
switch off climate control briefly.
Make sure the ignition switch is in the ON
position.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up. Airflow and air
distribution are set to automatic mode. or
Press the
button. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate the Cooling with air dehumidi-
fication function, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidification function
briefly.
The Cooling with air dehumidification function
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.
Problems with the Cooling with air dehumidifi-
cation function
:
Problem: The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution: The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting automatic climate control to
automatic mode
Only automatic climate control features the
Control climate control automatically function.
4-48Display screen, heater and air conditioner, and audio system

In automatic mode, the set temperature is
maintained automatically at a constant level
The system automatically regulates the tem-
perature of the dispensed air, the airflow and
the air distribution.
The automatic mode functions optimally when
theCooling with air dehumidification function
is activated. If desired, cooling with air dehu-
midification can be deactivated.
If you deactivate the Cooling with air-
dehumidification function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The win-
dows can mist up more quickly. Therefore, only
deactivate the Cooling with air-
dehumidification function briefly.
To set climate control to automatic mode
:
Make sure the ignition switch is in the ON
position.
Set the desired temperature.
To activate: press the
button The indica-
tor lamp in thebutton lights up. Auto-
matic air distribution and airflow are activated.
To switch to manual mode: press the
orbutton
or Press the
orbutton. The indicator
lamp in thebutton goes out. Automatic
air distribution and airflow are deactivated.
Setting the temperature
Different temperatures can be set for the driv-
er’s and front-passenger sides. The set tem-
perature is automatically maintained at a con-
stant level.
Make sure the ignition switch is in the ON
position.
To increase or reduce temperature: turn control
1or9counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demister ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
footwell air ventilators.
Directs the airflow through the center
and side air ventilators as well as the
demister ventilators.
Directs the airflow through the footwell
and demister ventilators.
Directs the airflow through the demister ventilators, the center and side air ven-
tilators as well as the footwell air venti-
lators.
NOTE
Regardless of the air distribution setting, airflow
is always directed through the side air ventila-
tors. The side air ventilators can only be closed if
the adjusters are turned clockwise until they
engage.
To set the air distribution:
1. Make sure the engine is running.
2. Press the
orbutton repeatedly
until the desired symbol appears in the
display.
Setting the airflow
1. Make sure the ignition switch is in the ON position.
2. To increase or reduce airflow: press the
orbutton.
Display screen, heater and air conditioner, and audio system4-49

Switching the ZONE function on/off
This function is only available with automatic
climate control.
To activate:press the
button. The indi-
cator light in thebutton lights up. The
temperature setting for the driver’s side is not
adopted for the front-passenger side.
To deactivate: press the
button. The
indicator lamp in thebutton goes out.
The temperature setting for the driver’s side is
adopted for the front-passenger side.
Defogging the windshield
You can use this function to de-ice the wind-
shield or to defog the inside of the windshield
and the side windows.
NOTE
You should only select the Windshield demist-
ing function until the windshield is clear again.
Activating the Windshield demisting function
:
Make sure the ignition switch is in the ON
position.
To activate: press the
button The indica-
tor light in thebutton lights up. The climate control system switches to the
following functions:
•High airflow
•High temperature
•Air distribution to the windshield and front
side windows
•Air-recirculation mode off
NOTE
•The Windshield demisting function auto-
matically sets the blower output to the opti-
mum demisting effect. As a result, the airflow
may increase or decrease automatically after
the
button is pressed.
•You can adjust the blower output manually
while the Windshield demisting function is
in operation. Press the
orbutton.
Deactivating the Windshield demisting func-
tion
:
Press thebutton. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated Air-recirculation mode re-
mains deactivated.
or Turn temperature control
1or9counter-
clockwise or clockwise.
Defogging the windows
Windows misted up on the inside:
1. Activate theCooling with air dehu-
midification function.
2. Activate automatic mode
.
3. If the windows continue to mist up, activate the
Windshield demisting function.
NOTE
You should only select this setting until the
windshield is clear again.
Windows misted up on the outside
:
1. Activate the windshield wipers.
2. Set the air distribution to
or.
NOTE
You should only select this setting until the win-
dows are clear again.
Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
4-50Display screen, heater and air conditioner, and audio system

If you activate air-recirculation mode, the win-
dows can mist up more quickly, in particular at
low temperatures. Only use air recirculation
mode briefly to prevent the windows misting
up.
Activating air recirculation mode
:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.
Air-recirculation mode is activated automati-
cally at high outside temperatures or high
levels of pollution. When air-recirculation mode
is activated automatically, the indicator light in
the
button is not lit. Outside air is added
after about 30 minutes.
Deactivating air recirculation mode
:
Press thebutton. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated automati-
cally:
•After approximately five minutes at outside
temperatures below approximately 45oF
(7oC).
•After approximately five minutes if the Cool-
ing with air dehumidification function is
deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45oF
(7oC) if the cooling with air dehumidification
function is activated.
SERVICING AIR CONDITIONER
WARNING
The air conditioner system contains refriger-
ant under high pressure. To avoid personal in-
jury, any air conditioner service should be
done only by an experienced technician with
the proper equipment.
The air conditioner system in your vehicle is
charged with a refrigerant designed with the
environment in mind.
This refrigerant will not harm the earth’s ozone
layer.
Special charging equipment and lubricant are
required when servicing your vehicle’s air con-
ditioner. Using improper refrigerants or lubri-
cants will cause severe damage to the air
conditioner system. (See Air conditioner sys-tem refrigerant and oil recommendations
in the
9. Maintenance and Schedules section.)
An INFINITI retailer will be able to service your
environmentally friendly air conditioner system.
Air conditioner filter
The air conditioner system is equipped with an
air conditioner filter. To make sure the air
conditioner heats, defogs, and ventilates effi-
ciently, replace the filter in accordance with the
specified maintenance intervals listed in the
separate maintenance booklet. It is recom-
mended you visit an INFINITI retailer for this
service.
The filter should be replaced if the air flow
decreases significantly or if windows fog up
easily when operating the heater or air condi-
tioner.
Display screen, heater and air conditioner, and audio system4-51

NAMES AND FUNCTIONS OF AUDIO
CONTROL BUTTONSMain audio buttons
1<SEEK•CAT•TRACK>:
Functions to seek radio stations or to skip
and fast-forward/rewind through tracks.
2<>:
Push to eject a disc.
3<RADIO>:
Push to switch to the radio mode. The
radio band will switch between AM, FM,
and SXM (SiriusXM) each time the button
is pushed.
4<MEDIA>:
Each time the button is pushed, a differ-
ent audio source (CD, iPod, USB or
Bluetooth® Streaming Audio) will be se-
lected.
5Disc slot:
Insert a disc with the label side facing up.
6<TUNE•CH•FOLDER>:
Functions to manually tune AM/FM , to
select SXM categories and to select MP3/
WMA/AAC folders.
7Radio memory buttons: Up to six preferred
stations can be registered in the preset
list for each band.
8<VOL/>:
Push to turn the audio system on/off.
Turn to adjust the volume.
Audio APPS information will be displayed when
music is played via INFINITI InTouch Apps.
NAA1704
Display screen, heater and air conditioner, and audio system4-63

Steering wheel mounted audio
control buttons
1System on/off: Push to turn on/off the
audio system.
2Volume control: Push the upper <+> or
lower <-> buttons to increase or decrease
the volume.
INFINITI controller AUDIO button
Push<AUDIO> to display the current audio
screen.
NAA1620NAA1726
4-64Display screen, heater and air conditioner, and audio system

MAIN AUDIO OPERATION
Turning audio system on/off
The ignition switch must be in the ACC or ON
position to turn on the audio system. Push
<VOL/
>or <>on the steering wheel to
turn on the last audio source which was playing
immediately before the system was turned off.
To turn off the audio system, push <VOL/
>
or <>on the steering wheel again.
Selecting audio source
1. Turn on the audio source menu screen by
touching [Source] on the upper left corner of
the audio screen.
2. Select an item from the audio source menu screen.
•Pushing <RADIO> or<MEDIA> can also
change the audio source.
See Main audio buttons earlier in this
section.
•If the audio system has been turned off while
one of the audio sources was playing, turn-
ing the audio system back on will play the
audio source that was playing when the
system was turned off.
•The audio source can also be changed with
the source bar on top of the audio screen.
•Audio APPS information will be displayed
when music is played via INFINITI InTouch
Apps.
Audio source bar
The audio source can be changed with the
source bar on top of the audio screen. The
source bar display can be turned on/off.
Turning source bar on/off
:
You can select whether the source bar on top of
the audio screens is displayed or not.
NAA1714
Display screen, heater and air conditioner, and audio system4-65

NOTE
When the stereo broadcast signal is weak, the
radio will automatically change from stereo to
monaural reception.
Seeking stations/channels
:
AM and FM Radio
Push<SEEK•CAT•TRACK> to tune from low to
high or high to low frequencies and to stop at
the next broadcasting station.
SiriusXM Satellite Radio
Push <SEEK•CAT•TRACK> to tune to the first
channel of the next or previous category.
Scan tuning
:
To tune the stations/channels, touch [Control]
on the display and touch [Scan]. The stations/
channels will be tuned form low to high fre-
quencies and stop at each broadcasting
station/channel for 5 seconds. Touching [Scan]
again during this 5 second period will stop scan
tuning and the radio will remain tuned to that
station/channel.
Presetting
:
Up to 36 stations/channels can be registered
for AM, FM and SXM in the preset list.
1. Select a radio band (AM, FM or SXM). 2. Tune to the station/channel you wish to
store in the preset list.
3. (Radio screen operation) Touch and hold one of the preset numbers in the preset list.
(Radio memory buttons operation) Push and
hold the desired station/channel preset but-
ton <1> to <6>.
4. The information such as frequency (AM/FM), channel number (SXM), etc. will be dis-
played on the preset list.
To change the preset stations/channels, touch
and hold one of the preset numbers. You can
select whether to change the station/channel or
to delete the preset setting.
Alert notification (SXM only)
:
Favorite artists and songs can be registered to
receive an alert notice wen a song of the
registered conditions is on the radio. To tune to
the respective channel, touch [Listen to be
consistent]. The alert can be ignored by touch-
ing [Cancel].
Satellite Radio:
•The satellite mode requires and active
SiriusXM Satellite Radio subscription. The
satellite service is available only to those at
least 18 and older in the 48 contiguous
United States.
•It may take some time to receive the activa-
tion signal after the initiation of the SiriusXM
Satellite Radio subscription. After receiving
the activation signal, an available channel
list will automatially be updated in the radio.
Switch the ignition switch from LOCK to ACC
to update the SiriusXM channel list.
Radio Controls
Touch [Control] on the AM, FM or SXM screen to
display the control screen.
The following items are available:
FM/AM
:
•[Station List]
Touch to display the available station list.
While listening to FM radio, Auto Update is
not performed.
•[Scan]
Touch to scan tune the stations
See Radio operation earlier in this section
•[HD mode]
When this item is turned on, the analog and
digital reception switches automatically.
When this item is turned off, te reception is
fixed in the analog mode.
4-68Display screen, heater and air conditioner, and audio system

For CDs without compressed audio files:
ModeScreen display
Disc Repeat
Disc
1 Track Repeat
1 Track
Disc Random
Disc
For CDs with compressed audio files:
Mode Screen display
Disc Repeat
Disc
1 Folder Repeat
1 Folder
1 Track Repeat
1 Track
Disc Random
Disc
1 Folder Random
1 Folder
CD player operation
Loading:
Insert the CD into the slot with the label side
facing up. The CD will be guided automatically
into the slot and starts playing.
After loading the CD, the CD screen will appear
on the display. Activation and playing
:
The CD mode can be selected from the source
list or by pushing the
<MEDIA>button with a CD
loaded to play the CD.
For details, see Selecting audio source earlier
in this section and Main audio buttons earlier
in this section.
If the system has been turned off while the CD
was playing, pushing <VOL/
>will start the
Audio system set to the CD screen.
Selecting track/folder
:
Touch [Track] or [Folder] in the CD menu and
select a preferred track or folder from the list.
Push <SEEK•CAT•TRACK> to move to the next or
previous track.
For CDs with compressed audio files, push
<TUNE•CH•FOLDER> to move to the next or
previous folder.
For details, see Main audio buttons earlier in
this section.
Fast-forwarding/rewinding
:
Push and hold <SEEK•CAT•TRACK> to fast-
forward or rewind the track. Release
<SEEK•CAT•TRACK> to play the track at normal
speed. Scanning
:
Touch [Scan] on the display to scan the tracks in
the CD. While scanning, the CD will play the first
10 seconds of each track and move on to the
next track. Pushing [Scan] again within the 10
seconds will stop scanning.
Changing play mode
:
Touch [Play Mode] or the play mode icon
([]or[]) to select the play mode.
Ejecting CD
:
Push <>to eject the CD. If the CD is
ejected and left unremoved, it will be reloaded
into the slot to protect the CD.
USB (UNIVERSAL SERIAL BUS)
CONNECTION PORT
Connecting USB memory device
WARNING
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
Display screen, heater and air conditioner, and audio system4-71